• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.28 no.5
• /
• pp.1233-1246
• /
• 2018

With the proliferation of smart mobiles, disassembly techniques for position-independent code (PIC) composed of ARM architecture instructions in computer security are becoming more important. However, existing techniques have been studied on x86 architecture and are focused on solving problems of non-PIC and generality. Therefore, the accuracy of the collected address information is low to apply to advanced security technologies such as binary measurement. In this paper, we propose a disassembly technique that reflects the characteristics of PIC composed of ARM instructions. For accuratly collecting traceable addresses, we designed value-set analysis having symbol-form domain. To solve the main problem of disassembly, we devised a heuristic using the characteristics of the code generated by the compiler. To verify the accuracy and effectiveness of our technique, we tested 669 shared libraries and executables in the Android 8.1 build, resulting in a total disassembly rate of 91.47%.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.17 no.2
• /
• pp.59-63
• /
• 1981

For the purpose of surveying accuracy of the position fix and local fluctuation of Omega signals in south coast of Korea, the author observe continuously the phase difference of the A-C pair and A-E pair form December 1, 1980, to February 28, 1981, at Cheju(33$^{\circ}$31'.0N, 126$^{\circ}$31.9E) and Busan(35$^{\circ}$7'.9 N, 129$^{\circ}$6'. 3 E). The analyzed results are as follows: 1. Omega signals at Cheju and Busan are positive correlation. Mean value of coefficients during all measured time is 0.70 with A-C pair and 0.75 with A-E pair. 2. Range of mean value of difference between the measured PPC at Cheju and Busan is 17.7~21.3 cels with A-C pair and -2.9~2.0 cels with A-E pair. 3. In case of using the differential Omega at Cheju and Busan, mean value of total errors of the position fix is 1.52 miles and its standard deviation is 0.21 miles.

• Journal of the Korean Society of Radiology
• /
• v.17 no.3
• /
• pp.351-357
• /
• 2023

This Study Rreceived Subjective Evaluation ROC Evaluation from five projection. of projection. at a University Hospital to Obtain and Diagnose Sharp images of apophyseal joints and Vertral arch of Thoracic vertebrae from thoracic X-ray projection. In the Subjective evaluation, the highest Score was obtained by raising the phantom from Supine to LAO by 70° and scoring 20 points at 5° with the X-ray Tube facing the head. In addition, he scored the highest score of 19 points at 8° with the Prone Phantom standing 60° with RAO and the X-ray Tube facing the head. For Objective Evaluation, the Signal-to-noise ratio, was calculated. ROI was set at 1,564 mm2 to obtain the image signal average value (Mean value) and the Standard deviation (SD value). Objective Evaluation The signal-to-noise ratio, was the highest at 5° toward the head in the LPO 70° position of the phantom in the lying position of the Thoracic spine projection, and the Thoracic Spine was the highest at 8° toward the head of the RAO posture of 5,645.

• Transactions of Materials Processing
• /
• v.13 no.3
• /
• pp.253-261
• /
• 2004

The machining technology for the brittle materials such as ceramics are applied to the fields of MEMS(micro electromechanical system) by the progress of new machining technologies such as Etching, Diamond machining, Micro drilling, EDM(Electro discharge machining), ECDM(Electro discharge machining), USM(Ultrasonic machining), LBM(Laser beam machining), EBM(Electron beam machining). Especially, the USM technology can be applied to the dieletric brittle materials such as silicon, borosilicate glass, silicon nitride, quartz and ceramics with high aspect ratio. The micro machining system with machining force controlled position servo is developed in this paper and the optimized ultrasonic machining algorithm is constructed by the force controlled position servo control. The load cell is adapted in the force measuring and the servo control algorithm, suit for the ultrasonic machining characteristics, is estabilished with using the PID auto-tunning functions at the PMAC system which is generally adapted in the field of robot industries. The precision force signal amplifier is constructed with high precision operational amplifier AD524. The vacuum adsorption chuck which is made of titanum and internal flow line is engraved, is used in the workpiece fixing. The mahining results by USM shows that there are some deviation between the force command and the actual machining force that the servo control algorithm should be applied in the machining procedures. Therefore, the constant force controlled position servo system is developed for the micro USM system and by the examination machining process in USM, the stable USM system is realized by tracking the average value of machining force.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.10 no.4
• /
• pp.55-64
• /
• 2001

In this study, hemisphere and cylindrical shapes were machined for different tool paths and machining conditions with ball endmill cutters. Tool deflection, cutting forces and shape accuracy were measured according to the inclination position of the sculptured surface. As the decreasing of inclination position angle, the tool deflection was increased due to the decreased cutting speed when the cutting edge is approaching toward the center. Tool deflection when upward cutting is obtained less than that of downward cutting and down-milling in upward cutting showed the least tool deflection for the sculptured surface. Roundness values were found in least roundness error when down-milling in upward cutting. It is obtained the very little difference between 90。and 45。 of inclination position angle. The best surface roughness value was obtained in upward up-milling and showed different tendency with tool deflection and cutting force. For down-milling, the cutting resistance of the side wall direction is larger than that of feed direction. Therefore, this phenomenon which is received over cutting resistance can be caused of chatter.

• Journal of Power Electronics
• /
• v.14 no.3
• /
• pp.564-571
• /
• 2014

Rotor initial position is an important factor affecting the control performance of electrically excited synchronous motors. This study presents a novel method for estimating rotor initial position based on sliding discrete Fourier transform (sDFT). By injecting an ac excitation into the rotor winding, an induced voltage is generated in stator windings. Through this voltage, the stator flux can be obtained using a pure integral voltage model. Considering the influence from a dc bias and an integral initial value, we adopt the sDFT to extract the fundamental flux component. A quadrant identification model is designed to realize the accurate estimation of the rotor initial position. The sDFT and high-pass filter, DFT, are compared in detail, and the contrast between dc excitation and ac injection is determined. Simulation and experimental results verify that this type of novel method can eliminate the influence of dc bias and other adverse factors, as well as provide a basis for the control of motor drives.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.3
• /
• pp.141-146
• /
• 2018

Recently, location recognition technology has attracted much attention, especially for locating people or objects in an indoor environment without being influenced by the surrounding environment GPS technology is widely used as a method of recognizing the position of an object or a person. GPS is a very efficient, but it does not allow the positions of objects or people indoors to be determined. RFID is a technology that identifies the location information of a tagged object or person using radio frequency information. In this study, an RFID system is constructed and the position is measured using tags. At this time, an error occurs between the actual and measured positions. To overcome this problem, a neural network is trained using the measured and actual position data to reduce the error. In this case, since the number of read tags is not constant, they are not suitable as input values for training the neural network, so the neural network is trained by converting them into center-of-gravity inputs and median value inputs. This allows the position error to be reduce by the neural network. In addition, different numbers of trained data are used, viz. 50, 100, 200 and 300, and the correlation between the number of data input values and the error is checked. When the training is performed using the neural network, the errors of the center-of-gravity input and median value input are compared. It was found that the greater the number of trained data, the lower the error, and that the error is lower when the median value input is used than when the center-of-gravity input is used.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.30 no.4
• /
• pp.389-396
• /
• 2012

As the demand on the precise positioning for the moving objects has been increased in the various industry field, many studies have been conducted to analyze real time kinematic technique and its practical usage. The main purpose of this study is to analyze the possibility of Network-RTK(VRS) in real-time kinematic positioning. So, the accuracy analysis has been conducted by comparing the Network-RTK(VRS) position with respect to the RTK position. As a result, Network-RTK(VRS) based on kinematic positioning has centimeter level of RMS in the ideal environment compared to RTK positioning. However, when the integer ambiguities was lost, the accuracy of Network-RTK was meter level. At that time, the quality value has been changed dramatically and shows big correlation with accuracy. When the position and height quality values are within 0.1m, the RMS of the horizontal and vertical position appears better than 10cm and 20cm, respectively. However, if the quality value is over 0.1m, the RMS increases to larger than a meter. Therefore, it is recommended to check the quality value when conducting Network-RTK(VRS) kinematic positioning to get the centimeter level accuracy.

• Journal of the Korean Society of Radiology
• /
• v.9 no.6
• /
• pp.337-342
• /
• 2015

The one-year-follow-up test of abdomen/pelvis from 10 patients who were scanned more than twice a years were analyzed the radiation dose and image quality depend on the position of the arm retrospectively from January to December in 2013. There were classified two groups, group A was examined with raising an arm on standard position and group B was performed with lowering an arm, respectively. Group A of an average mAs from the first dose amount was shown 11.4% less compared to Group B. And the value of CTDI from Group B also was investigated 11.3% less. To compare the quality comparison of the second image as histogram value, the value of max from both of two groups was measured similarly. However, a big difference was shown from the value of min and SD, the short dose was appeared depends on the position of arm even though Group A was radiated more than Group B. Less exposure to the medical image quality only by working CT scan when the examiner actively raise the arm before the development and testing of high-end equipment introduction of complex algorithms for obtaining an optimized image will be provided to the patient.

• 한국디지털정책학회:학술대회논문집
• /
• 2005.06a
• /
• pp.107-143
• /
• 2005

Mobile service that geography, position by development of space Information Technology and technology of communications, space are various to us now becoming limelight as point contents and infra information that customers do demand based on radio superhigh speed authentication net on highly information society by offer infringement problem about individual's privacy or information by political and scientific interest be injured. Purpose of this study grasps use factor of LBS application Mobile service, and it is that analyze actual proof through questionnaire to grasp whether some relation is with value and action determination that is felt of LBS application Mobile service. Distributed all question of 190 copies but disk floret inclination did valid data 171 that clear question and omission remove a lot of questions by type of study among questionnaire of collected 182 wealths. Analyzed factor analysis and authoritativeness to search validity and confidence of questionnaire and used single regression analysis and multiple regression analysis for hypothetical verification. According to verification result, Mobile service that apply position base service usefulness and system quality, adaptedness of Mobile service that apply position base service by leading person affecting in use, acted for connection healthy and felt value is important factor immediately. Usability and social effect, felt expense, privacy did not appear by leading person that keep in mind in this study. Is been related with step that Mobile service that apply position base service is placed. That is, as present childhood, a person who have experience that use service to look for friend is few and usability fairly in last in wide application boundary and this very important person was removed finally in model. This study has sense in terms of study systematically about LBS application service use leading person that is getting into the spotlight worldwide among Mobile service that is injured newly.