• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.453-456
• /
• 2000

This paper presents experimental results on selecting optimal process parameters for UV-Vaccum casting. The UV-Vacuum casting is a relatively new process that allows very rapid mold preparation and part duplication via UV curing. Effect of various process variables such as pressure and temperature on mold strength and part accuracy was evaluated by using Taguchi method.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.9
• /
• pp.4178-4184
• /
• 2013

Nanoimprint lithography (NIL) is an emerging technology enabling cost-effective and high-throughput nanofabrication. Recently, the major trends of NIL are high throughput and large area patterning. UV curable type NIL (UV NIL) can be performed at room temperature and low pressure. And one advantage of UV NIL is that it does not need vacuum, which greatly simplifies tool construction, so that vacuum oprated high-precision stages and a large vacuum chamber are no longer needed. However, one key issue in non-vacuum environment is air bubble formation problem. Namely, can the air bubbles be completely removed from the resist. In this paper, the air bubbles formation by the method of droplet application in UV NIL with non-vacuum environment are experimentally studied. The effects of the volume of droplet and the number of dispensing points on air bubble formation are investigated.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.373-373
• /
• 2012

We fabricated conductive zinc oxide (ZnO) thin film at low temperature by UV-enhanced atomic layer deposition. The atomic layer deposition relies on alternate pulsing of the precursor gases onto the substrate surface and subsequent chemisorption of the precursors. In this experiment, diethylzinc (DEZ) and $H_2O$ were used as precursors with UV light. The UV light was very effective to improve the conductivity of the ZnO thin film. The thickness, transparency and resistivity were investigated by ellisometry, UV-visible spectroscopy and Four-point probe.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1996.02a
• /
• pp.144-144
• /
• 1996

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.351-352
• /
• 2012

UV LED에서 p-GaN층의 높은 일함수와 자체 면저항이 크기 때문에 current spreading layer인 ITO (indium tin oxide) 투명전극이 사용되고 있다. 따라서 높은 UV 파장대 투과율과 낮은 면 저항이 매우 중요하다. 본 연구에서, RF magnetron sputter를 사용하여 ITO 투명전극을 glass(boro33)에 120 nm 두께로 증착하였다. 그 후 RTA (rapid thermal annealing)을 이용해 120초 동안 $600^{\circ}C$에서 Air, $N_2$ (15 sccm), vacuum 환경에서 열처리를 하여 UV-Vis-NIR spectrophotometer를 사용해 ITO 박막의 투과율을 측정하고, Hall measurement system을 이용하여 전기적 특성을 측정하였다. Fig. 1과 같이 열처리 환경에 따라 ITO 박막의 투과율이 변하고 또한 Table 1과 같이 전기적 특성도 변함을 알 수 있었다. Air 환경에서의 열처리는 reference 샘플과 비교 했을 때 400 nm 이하의 파장에서 투과율이 증가하였지만 400 nm 이상의 파장에서는 투과율이 낮아짐을 볼 수 있고, 면 저항 (Ohm/sq)은 오히려 reference (as deposited) 샘플과 비교하여 24 Ohm/sq 증가하는 것을 알 수 있었다. 반면에 $N_2$, vacuum 환경에서 열처리는 reference (as deposited) 샘플 보다 380 nm 파장대에서 16% 정도 높은 투과율을 보였고, 면저항 역시 2배 이상 낮아졌다. 둘 다 비슷한 투과율과 면저항을 나타내었지만 vacuum 환경이 좀 더 우수한 광학적 특성을 나타내었고 반면에 $N_2$ 환경은 좀 더 낮은 면저항을 나타내었다. ITO 박막을 증착한 후 vacuum 환경에서 열처리를 통하여 제작된 UV-LED (중심 파장 380 nm)가 Fig. 2와 같이 입력 전류 450 mA에서 광출력이 46% 정도 향상 되었고 안정된 I-V 특성 보였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.312.1-312.1
• /
• 2016

We have deposited ZnO thin films by ultraviolet (UV) enhanced atomic layer deposition using diethylznic (DEZ) and water (H2O) as precursors with UV light. The atomic layer deposition relies on alternating dose of the precursor on the surface and subsequent chemisorption of the precursors with self-limiting growth mechanism. Though ALD is useful to deposition conformal and precise thin film, the surface reactions of the atomic layer deposition are not completed at low temperature in many cases. In this experiment, we focused on the effects of UV radiation during the ALD process on the properties of the inorganic thin films. The surface reactions were found to be complementary enough to yield uniform inorganic thin films and fully react between DEZ and H2O at the low temperature by using UV irradiation. The UV light was effective to obtain conductive ZnO film. And the stability of TFT with UV-enhanced ZnO was improved than ZnO by thermal ALD method. High conductive UV-enhanced ZnO film have the potential to applicability of the transparent electrode.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.155-156
• /
• 2006

UV-NIL is a promising technology for the fabrication of sub-100 nm features. Due to non-uniformity of the residual layer thickness (RLT) and a strong possibility of defects, many UV-NIL processes have been developed and some are commercially available at present, most are based on the 'step-and-repeat' nanoimprint technique, which employs a small-area stamp, much smaller than the substrate. This is mainly because, when a large-area stamp is used, it is difficult to obtain acceptable uniform residual layer thickness and/or to avoid defects such as air entrapment. As an attempt to enable UV_NIL with a large-area stamp for high throughput, we propose a new UV-NIL tool that is able to imprint 4 inch wafer in a low vacuum environment at a single step.

• Journal of the Korean Vacuum Society
• /
• v.4 no.3
• /
• pp.261-269
• /
• 1995

본 실험에서는 실리콘 웨이퍼 위에 photoresist(PR)와 octadecyltrichlorosilane(OST, CH3((CH2)17SiCI3)를 입혀서 UV/zone 처리를 어떻게 유기물질들이 UV/zone과 반응하여, 어떻게 표면에서 제거되는지를 in-line으로 연결된 XPS로 분석하고 반응시킨 표면들의 거칠기(roughness)를 AFM을 이용하여 관찰하였다. 실험결과 상온에서 UV/zone 처리를 했을 경우, PR과 OTS같은 유기물질이 표면에서 산화되는 것을 알 수 있었으나 이들이 제거되지 않고 표면에 그대로 남아있음을 알 수 있었다. 그러나 가열하면서(PR:$250^{\circ}C$, ORS:$100^{\circ}C$)UV/ozone 처리를 하였을 경우 표면에서 산화됨과 동시에 이들 산화물들이 표면에서 제거됨을 알 수 있었다. XPS 분석으로부터 이들의 산화반응물은 PR과 OTS 모두 -CH2-, -CH2O-, =C=O, -COO-를 가지는 것으로 나타났으며, 열에너지에 의해서 이들이 표면에서 제거되는 것으로 나타났다. AFM 분석결과는 상온에서 UV/ozone 처리를 하였을 경우에 표면의 거칠기가 적은 반면, 가열하면서 UV/o-zone처리를 하였을 경우에는 표면의 거칠기가 다소 증가하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.256-256
• /
• 2011

We have deposited Al2O3 thin films on Si substrates at room temperature by UV-enhanced atomic layer deposition using trimethylaluminum (TMA) and H2O as precursors with UV light. The atomic layer deposition relies on alternate pulsing of the precursor gases onto the substrate surface and subsequent chemisorption of the precursors. In many cases, the surface reactions of the atomic layer deposition are not completed at low temperature. In this experiment, the surface reactions were found to be self-limiting and complementary enough to yield uniform Al2O3 thin films by using UV irradiation at room temperature. The UV light was very effective to obtain the high quality Al2O3 thin films with defectless.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.211.1-211.1
• /
• 2013

We fabricate the conductive zinc oxide(ZnO) thin film using UV-enhanced atomic layer deposition. ZnO is semiconductor with a wide band gap(3.37eV) and transparent in the visible region. ZnO can be deposited with various method, such as metal organic chemical vapour deposition, magnetron sputtering and pulsed laser ablation deposition. In this experiment, ZnO thin films was deposited by atomic layer deposition using diethylzinc (DEZ) and D.I water as precursors with UV irradiation during water dosing. As a function of UV exposure time, the resistivity of ZnO thin films decreased dramatically. We were able to confirm that UV irradiation is one of the effective way to improve conductivity of ZnO thin film. The resistivity was investigated by 4 point probe. Additionally, we confirm the thin film composition is ZnO by X-ray photoelectron spectroscopy. We anticipate that this UV-enhanced ZnO thin film can be applied to electronics or photonic devices as transparent electrode.