• Tribology and Lubricants
• /
• v.19 no.2
• /
• pp.94-101
• /
• 2003

Used motor oil contains pollutants, including organic chemicals and meta]s. When disposed of improperly - in the trash, on the ground or in a sewer system - the pollutants may reach rivers, lakes or the ground water. Thus, all the waste oil products such as waste motor oil, waste oil container, and waste oil filter should be collected and transported for recycling or disposal by waste oil regulations. Because waste oil container is a valuable resource, waste oil containers can be reused, cleaned, buried, and burned for recycling processes. This paper presents the integrated management system that may increase the efficiency and productivity for collecting and reprocessing waste oil containers such as steel can and plastic container. The integrated management system consists of collection and transportation process management system and confirmation and certification process management system for waste oil containers.

• Geomechanics and Engineering
• /
• v.20 no.4
• /
• pp.299-312
• /
• 2020

The aim of this paper was to investigating the effects of soil relative density, construction materials roughness, oil type (gasoil, crude oil, and used motor oil), and oil content on the internal and interface shear behavior of sand with different construction materials by means of a modified large direct shear test apparatus. Tests conducted on the soil-soil (S-S), soil-rough concrete (S-RC), soil-smooth concrete (S-SC), and soil-steel (S-ST) interfaces and results showed that the shear strength of S-S interface is always higher than the soil-material interfaces. Internal and interface friction angles of sand beds increased by increase in relative density and decreased by increasing oil content. The oil properties (especially viscosity) played a major role in interface friction behavior. Despite the friction angles of contaminated sands with viscous fluids drastically decreased, it compensated by the apparent cohesion and adhesion developed between the soil grains and construction materials.

• Clean Technology
• /
• v.15 no.1
• /
• pp.54-59
• /
• 2009

In this study, the separation of water/bitumen emulsion was investigated by chemical demulsification method. Motor oils (GS Caltex Deluxe Gold V 7.5W/30, Hyundai gear oil 85W/140) and asphalt (AP-5, KS M 2201, Dongnam Petrochemical MFG. Co.) were used as model oils in the preliminary experiments to effectively remove water from water/bitumen emulsion. The bitumen extracted from Canadian oilsands was used in this study. The water/oil emulsion was not separated without demulsifiers, and Hyundai motor oil showed higher efficiency of water separation at a low concentration of demulsifier compared with that for GS Caltex motor oil. However, as the concentration increased, the efficiency did not rapidly increase compared with that of GS Caltex motor oil. It was highly speculated that the water phase of Hyundai motor oil was not dispersed well compared with that of GS Caltex motor oil because the viscosity of Hyundai motor oil was much higher than that of GS Caltex motor oil. The demulsifier of higher HLB (hydrophilic - lipophilic balance) value had high separation efficiencies in water/oil emulsion. The TWEEN 20 (polyoxyethylene sorbitan monolaurate solution) showed better separation efficiency than other demulsifiers.

• Journal of the Korean Society for Precision Engineering
• /
• v.29 no.7
• /
• pp.793-798
• /
• 2012

Oil gear pump is used for the cooling pump system of commercial vehicle. The hydraulic pulsation pressure of oil gear pump is one of the most important reasons for the vibration and noise of the pump. In this study, the several hydraulic factors acting on oil gear motor are analyzed by CFD in operation of cooling system. Forced vibration analysis due to hydraulic pulsation pressure is analyzed by FEA for predicting deformation and equivalent stress.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.8
• /
• pp.86-91
• /
• 1995

Recently, motor integrated spindle is often used in a high speed spindle system of machine tools in order to increase machining speed. The important problem in high speed motor integrated spindle is to reduce thermal effect occured by motor and ball bearings. In this study, the effect of heat transfer from motor is investigated. The experimental equipment is composed with oil-air lubrication method, air cooling system and angular contact ball bearings. The results show that the thermal effect in motor is larger than in ball bearing until DmN 8000,000 with air cooling.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2004.11a
• /
• pp.233-236
• /
• 2004

An experimental study was conducted to evaluate characteristic variation of diluted engine oil by diesel fuel and its effects on engine components. Especially, engine oil was made to have $15\%$ fuel content. To predict existing diesel fuel content in engine oil after test was used the viscosity calibration curve. About $54\%$ percent of diesel fuel in diluted engine oil was distillated by various paths related to reciprocating motion of piston and the rest diesel fuel plays an important role for decreasing engine oil viscosity. Test results show that lowered engine ell viscosity by diesel fuel dilution become a reason of increasing engine elements wear, Therefore, this caused the quantity of blow-by gas to increase and main gallery pressure to decrease.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.05a
• /
• pp.53-56
• /
• 2008

When someone measuring for pressure of a Solid Rocket Motor(SRM) at Static Firing Test, generally, used with pressure tube to be filled in Oil. But, if you used pressure tube with oil, you were worried about possibility of spilled oil when you measured pressure in SRM at high altitude environment. Because it usually connected at ignitor. In this paper, We described how to make a pressure tube without oil and matters to be attended to design it.

• Tribology and Lubricants
• /
• v.11 no.5
• /
• pp.71-77
• /
• 1995

The capacitance technique was used to measure the minimum oil film thickness in engine bearing and the central oil film thickness between cam and tappet. This method is based on the measurement of total capacitance of oil film. For the measurement of the oil film thickness between cam and tappet, two surfaces were assumed to be flat and parallel within the Hertzian region and all the measured capacitance originated from this region. Shear rates from the measured minimum oil film thickness are over 10$^{6}$ sec$^{-1}$ in the greater part in both two cases. The minimum oil film thickness in engine bearing is larger than the surface roughness. Between cam and tappet it is mostly smaller than the surface roughness. In spite of the awkward restriction of the reliability of measured oil film thickness, it was known that the capacitance technique makes it possible to measure the oil film thickness in elastohydrodynamic and mixed lubrication regimes as well as in hydrodynamic regime. Therefore, it is also possible to classify the lubrication regimes based on the oil film thickness.

• Tribology and Lubricants
• /
• v.10 no.1
• /
• pp.14-26
• /
• 1994

The minimum oil film thickness(MOFT) in the connecting-rod bearing of a 1.5 liter, L-4, gasoline engine is measured up to 5500 rpm and calculated to study the dynamically loaded engine bearing. Short bearing approximation and Mobility method are used for theoretical analysis of oil film characteristics. And cylinder pressure, crank-pin surface temperature and bearing temperature are measured as the input data of theoretical analysis. The MOFT are measured by the total capacitance method(TCM). To improve the reliability of the test results, a reasonable determination method of bearing clearance is introduced and used, and the effects of cavitation and aeration on the test results are neglected. The crankshaft is grounded by means of a slip ring. A scissor type linkage system was developed to measure the MOFT and bearing temperature. The effects of engine speed, load and oil viscosity on the measured and calculated minimum oil film thicknesses are investigated at 1500 to 5500 rpm. From the comparison between the measured and calculated MOFT, it is found that a qualitative similarity exists between them, but in all cases, the measured MOFT are smaller than those calculated.

• Journal of Ecology and Environment
• /
• v.37 no.2
• /
• pp.41-51
• /
• 2014

This study investigated the ability of Bothriochloa bladhii (Retz.) S.T. Blake (Poaceae), Cyperus ligularis L. (Cyperaceae), Commelina erecta L. (Commelinaceae), Mariscus umbellatus (Rottb.) Vahl (Cyperaceae), Fimbistylis miliacea L. (Cyperaceae) and Torulinium odoratum L. (Cyperaceae) to clean up various levels of used motor oil (UMO) contaminated soils. The plants were grown in 2 kg garden soils treated to 0%, 1%, 5% and 10% levels of UMO contamination. The plant growth parameters, chlorophyll contents and dry weight of test plants were measured. The phytoremediation ability of these test plants were assessed by measuring the uptake of hydrocarbons in terms of total hydrocarbon content (THC) as well as their percentage degradation values. There was significant (P < 0.05) reduction in leaf chlorophyll contents and dry weights of the test plant species planted in UMO contaminated soils. THC as well as the percentage uptake (or degradation) of hydrocarbons were both lowest in C. ligularis but highest in T. odoratum in all cases. The phytoremediation potential of test plants was highest in soils contaminated with 5% UMO. Based on the results of this study, all test plants with the exception of C. ligularis were potentially capable of undertaking phytoremediation. However, B. bladhii and T. odoratum proved most effective in the uptake and degradation of UMO.