• Nuclear Engineering and Technology
• /
• 제48권1호
• /
• pp.218-227
• /
• 2016

Background: Steam explosions may occur in nuclear power plants by molten fuel-coolant interactions when the external reactor vessel cooling strategy fails. Since this phenomenon can threaten structural barriers as well as major components, extensive integrity assessment research is necessary to ensure their safety. Method: In this study, the influence of yield criteria was investigated to predict the failure of a reactor cavity under a typical postulated condition through detailed parametric finite element analyses. Further analyses using a geometrically simplified equivalent model with homogeneous concrete properties were also performed to examine its effectiveness as an alternative to the detailed reinforcement concrete model. Results: By comparing finite element analysis results such as cracking, crushing, stresses, and displacements, the Willam-Warnke model was derived for practical use, and failure criteria applicable to the reactor cavity under the severe accident condition were discussed. Conclusion: It was proved that the reactor cavity sustained its intended function as a barrier to avoid release of radioactive materials, irrespective of the different yield criteria that were adopted. In addition, from a conservative viewpoint, it seems possible to employ the simplified equivalent model to determine the damage extent and weakest points during the preliminary evaluation stage.

• Design & Manufacturing
• /
• 제11권2호
• /
• pp.46-50
• /
• 2017

EPS used in lost foam casting elastic modulus is extremely low. So it is necessary to derive machining conditions for effective cutting. Therefore this study were analyzed end-milling machining conditions to affecting the surface roughness of EPS foam. The machining conditions were set to depth, feed, and RPM at 3-level. And 18experimental conditions were derived using mixed orthogonal array. The most important condition for surface roughness is RPM. In addition, RPM machining condition range test that can realize surface roughness less than $10{\mu}m$ was performed. he range of RPM conditions is more than 15,000. However the range of RPM conditions is a condition that is difficult to use in actual field. In the future variance analysis and experiments are needed to derive the range of machining conditions available.

• 펄프종이기술
• /
• 제46권5호
• /
• pp.35-42
• /
• 2014

Many historical archives have been deteriorated by aging with time. Various kinds of defects such as worm-hole, yellowing, brittleness are observed and their severity was dependent on raw material type, storage condition, and so on. For a long-term use and storage, a proper preservation treatment is required. Many studies on preservation and conservation have been carried out on hanji which was made from mulberry fiber, but there are few concerns on foreign paper. Therefore, aging and chemical strengthening treatment was done on paper made of bamboo and wood fibers depending on aging condition, the type and pickup weight of chemicals and treatment method. When methyl cellulose was treated with impregnation or brushing, the aged paper was strengthened effectively. The strengthening effect by chemicals was dependent on the aged condition of the paper.

• 한국염색가공학회지
• /
• 제31권3호
• /
• pp.187-194
• /
• 2019

Blowing film was prepared using polyester elastomer with thermally expandable microcapsule to investigate the optimum blowing properties and the film making process. Physical properties including specific gravity, blowing efficiency, foaming shape, tensile strength and elongation of polyester film were tested by varying the process condition of temperature and revolution per minutes of the extruder. The lowest specific gravity of 0.709 can be achieved with excellent foaming cells at $210^{\circ}C$ and 50 RPM conditions. The highest tensile strength and elongation was shown at $210^{\circ}C$, 100 RPM and $230^{\circ}C$, 25 RPM conditions. However, most of the prepared polyester films showed over $1kg_f/mm^2$ of tensile strength which is reasonable value to use in film applications.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2006년도 하계학술발표대회 논문집
• /
• pp.506-511
• /
• 2006

To today with the acceleration due to the preference actual condition of high-class energy national income level it is together improving. It follows hereupon and it is convenient and the neat heat source is increasing a tendency where it is. It investigates the government offices building in commerce portion from the research which it sees and from the draft it analyzes a coat dosage. And comparison it analyzes the movable present condition of thread use dosage and the freezer. It presents the improvement direction against enemy conditions heat source equipment selecting. Also, currently it produces the dosage of heat source equipment and application it tries. The result, the various safety rate and the premium rate which it uses universally are considered above thread using. The reappraisal for enemy conditions heat source equipment selecting which it follows hereupon is necessary.

• 한국분무공학회지
• /
• 제24권3호
• /
• pp.137-144
• /
• 2019

The Y-jet nozzle has benefits such as simple design and wide operating conditions. Because of these benefits, it is used in various combustion devices including industrial boilers. The most important variables in the design of the Y-jet nozzle are the mixing chamber length, the supply diameter of the liquid fuel and gas, and the exit orifice diameter. In addition, because of the use of a twin-fluid, optimized data is required depending on the spray condition. In this study, spray experiment was carried out under the pressure condition of 7 bar or more, which is the spraying condition used in industry. There was no change in flow rate with the length of the Y-jet nozzle mixing chamber, but the difference in SMD was confirmed. Adjusting the exit orifice diameter is most important to achieve the desired flow rate. Changes in the liquid and gas inlet port diameters ratio were found to be help improve the operating range and significant difference in SMD was observed.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제12권12호
• /
• pp.6034-6056
• /
• 2018

This paper describes two user studies in remote collaboration between two users with a video conferencing system where a remote user can draw annotations on the live video of the local user's workspace. In these two studies, the local user had the control of the view when sharing the first-person view, but our interfaces provided instant control of the shared view to the remote users. The first study investigates methods for assisting drawing annotations. The auto-freeze method, a novel solution for drawing annotations, is compared to a prior solution (manual freeze method) and a baseline (non-freeze) condition. Results show that both local and remote users preferred the auto-freeze method, which is easy to use and allows users to quickly draw annotations. The manual-freeze method supported precise drawing, but was less preferred because of the need for manual input. The second study explores visual notification for better local user awareness. We propose two designs: the red-box and both-freeze notifications, and compare these to the baseline, no notification condition. Users preferred the less obtrusive red-box notification that improved awareness of when annotations were made by remote users, and had a significantly lower level of interruption compared to the both-freeze condition.

• 융합정보논문지
• /
• 제9권6호
• /
• pp.211-217
• /
• 2019

본 연구는 스크럽 화장품을 사용하여 피부상태의 변화를 피부분석장비로 분석하고 마이크로비드의 형태적 특징을 더마스코프와 주사전자현미경으로 관찰하였다. 더마스코프 관찰에서 클렌징을 하는 과정 중의 얼굴피부에 붙어있는 마이크로비드는 서로 밀착되어 존재하고 있거나 분산되어 있었다. 클렌징 한 피부는 깨끗하고 매끄럽게 관찰되었으며 표피 각질세포들 사이의 미세한 주름이 줄어든 것을 확인하였다. 주사전자현미경 관찰에서 구슬모양의 마이크로비드 표면은 심한 굴곡이나 거친 표면을 가지고 있지 않았다. 스크럽을 하기 전과 후의 유분, 수분, pH의 변화를 비교분석한 결과 스크럽을 하기전의 피부가 스크럽 후의 피부보다 수분과 유분의 함량이 높게 나타났고 pH의 변화는 큰 차이가 없었다.

• 대한수학회지
• /
• 제59권6호
• /
• pp.1047-1065
• /
• 2022

For two dimensional lattices, a Gaussian basis achieves all two successive minima. For dimension larger than two, constructing a pairwise Gaussian basis is useful to compute short vectors of the lattice. For three dimensional lattices, Semaev showed that one can convert a pairwise Gaussian basis to a basis achieving all three successive minima by one simple reduction. A pairwise Gaussian basis can be obtained from a given basis by executing Gauss algorithm for each pair of basis vectors repeatedly until it returns a pairwise Gaussian basis. In this article, we prove a necessary and sufficient condition for a pairwise Gaussian basis to achieve the first k successive minima for three dimensional lattices for each k ∈ {1, 2, 3} by modifying Semaev's condition. Our condition directly checks whether a pairwise Gaussian basis contains the first k shortest independent vectors for three dimensional lattices. LLL is the most basic lattice basis reduction algorithm and we study how to use LLL to compute a pairwise Gaussian basis. For δ ≥ 0.9, we prove that LLL(δ) with an additional simple reduction turns any basis for a three dimensional lattice into a pairwise SV-reduced basis. By using this, we convert an LLL reduced basis to a pairwise Gaussian basis in a few simple reductions. Our result suggests that the LLL algorithm is quite effective to compute a basis with all three successive minima for three dimensional lattices.

• 한국산업융합학회 논문집
• /
• 제25권6_3호
• /
• pp.1127-1133
• /
• 2022

Recently, the use of aircraft structures using Ti alloy (Ti-6Al-4V), a lightweight high-strength alloy material, is rapidly increasing due to the weight reduction of aircraft. However, high-strength materials such as Ti alloys require high energy for cutting and are classified as difficult-to-cut materials. Also, research on Laser Assisted Machining (hereinafter referred to as LAM), a cutting processing technology that utilizes improved machinability, is being actively researched. Therefore, in this paper, in order to confirm the proper temperature distribution using a laser, the finite element method is used to determine the temperature distribution according to the calorific value condition to derive the appropriate condition, and the thermal load generated at this time is used as a structural analysis. It is intended to be used as basic data for LAM processing conditions by measuring the amount of residual stress and thermal deformation caused by heat.