• The korean journal of orthodontics
• /
• v.31 no.1 s.84
• /
• pp.97-105
• /
• 2001

In many cases of orthodontic treatment the upper anterior teeth are retracted. Periodontal problems may arise during incisor retraction, if the amount of tooth movement and the amount of remodeling in the anterior cortical bone are not the same. Therefore in this study, to find out the relationship between the amount of tooth movement and the amount of bone remodeling during retraction of the upper anterior teeth, lateral cephalograms of 56 female patients over 18-year-old were taken before and after treatment. Among the 56 patients, two groups were divided according to the type of root movement during retraction. 26 patients mainly moved by tipping and 30 by bodily movement. The cephalograms taken before and after treatment were superimposed upon the true horizontal plane. In the Tip-Group, the horizontal bone remodeling/tooth movement ratio was 1:1.63, and in the Torque-Group it was 1:1.66. Because the amount of tooth movement and the amount of bone remodeling were not the same in both groups, in the Tip-Group the root apex moved away from the palatal cortical plate and closer to the labial cortical plate, whereas in the Torque-Group the root moved away from the labial cortical plate and closet to the palatal cortical plate. Therefore, there are limitations in the amount of incisor retraction in patients with a very thin anterior cortical plate in the maxilla, and in patients with severe skeletal discrepancies orthognathic surgery should be considered and when orthodontic camouflage treatment is the only possible method, the orthodontist must be aware of the limitations of treatment.

• 제어로봇시스템학회:학술대회논문집
• /
• 1997.10a
• /
• pp.257-260
• /
• 1997

In this paper, the double inverted pendulum having a single actuator is built and the controller for the system is proposed. The lower link is hinged on the plate to free for rotation in the x-z plane. The upper link is connected to the lower link through a DC motor. The double inverted pendulum built can be kept upright posture by controlling the position of the upper link even though the proposed inverted pendulum has no actuator in lower hinge. The algorithm to control the inverted pendulum is consisted of a state feedback controller within a linearizable range and a fuzzy logic controller coupled with a feedback linearization control for the rest of the range. Concept of the virtual work is employed to drive the linearlized model for the state feedback controller. The feedback linearization controller drives a DC motor with the modified reference joint angle from the fuzzy controller which adjusts a upright posture of a proposed pendulum system. Finally, the experiments are conducted to show the validity of the proposed controller.

• Proceedings of the KSME Conference
• /
• 2001.06d
• /
• pp.509-515
• /
• 2001

In a square cavity, the flow phenomena in the surrounding of the bubble attached at the upper cooled solid wall were studied by using a thermo-sensitive liquid-crystal tracer and image processing techniques. This method offers the advantage of measuring the entire flow field in a selected plane within the fluid at a given instant of time in contrast to point by point method like T/C. Quantitative data of the temperature were obtained by applying a colour-image-processing to the. visualized image. As the growing of a bubble, In a bubble size appears the flow phenomena which the direction of flow is reversed in the entire temperature and flow field. The observed phenomena are described with regard to thermocapillary convection.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.7
• /
• pp.1168-1175
• /
• 2000

To observe propagation characteristics of microstrip lines on YIG film, the FDTD is employed. For various GGG substrate and YIG film, the dispersion curves and the bandwidth of the cutoff region are calculated. And the distribution of the electric fields of the transverse plane underneath the conductor strip is obtained near upper and lower cutoff frequency. The results of two and three dimensional FDTD for the upper cutoff frequency are compared with spectral domain approach(SDA). A good agreement is verified, although there is relative error 6% between the results calculated by the two methods.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1993.10a
• /
• pp.218-223
• /
• 1993

An UBET(Upper Bound Elemental Technique) program has been developed to analyze forging load, die-cavity filling and effective strain distribution for flashless forging. To analyze the process easily, it is suggested that the deformation is divided into two different parts. Those are axisymmetric part in corner and plane-strain part in lateral. The total power consumption is minimized through combination of two deformation parts by building block method, from which the upper-bound forging load, the flow pattern, the grid pattern, the veocity distribution and the effective strain are determined. To show the merit of flashless forging, the result of flashless and flash forging processes are compared through theory and experiment. Experiments have been carried out with plasticine billets at room temperature. The theoretical predictions of the forging load and the flow pattern are in good agreement with the experimental results.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.25 no.4
• /
• pp.366-371
• /
• 1988

A parallel-plate waveguide with a slit in its upper plate is analysed. An integral equation is formulated for the equivalent magnetic current and solved by the conventional moment method. Numerical results are presented for the magnetic current, reflection and transmission coefficients, a normalized radiated power in the slit, and equivalent circuit parameters. The equivalent circuit parameters are an useful quantities in the study of the E-plane coupled microstrip antennas.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.6
• /
• pp.142-148
• /
• 1997

In this paper, forging of internal triangular and involute serrations are analyzed by upper bound method. Kinematically admissible velocity fields for half pitch of the serration were proposed. It was assumed that the shape flow surface during forging is a straight line perpendicular to plane of symmetry. Using the suggested velocity fields, forging loads and relative pressures were calculated by numerical method. Experiments were carride out with commercial AI 2024 aluminium alloy. As a result, the calculated solutions are good agreement with experimental results, so it is useful to predict the loads for forging of internal serrations.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.03b
• /
• pp.111-114
• /
• 1999

The twisting and extrusion process of the product with involute helical fin from the round billet is developed by the upper bound analysis. The twisting of extruded product is caused by the twisted die surface connecting the die entrance section and the die exit section linearly. In the analysis, the internal shear surface is defined as the curved twisted plane from the taisting of die surface and the shear work is calculated by the consumption of shear energy The increase rate of angular velocity is determined by the minimization of plastic work. The results of the analysis show that the angular velocity of the extruded product increases with the die twisting angle, the reduction of area, and decreases with the die length, the friction condition.

• Kyungpook Mathematical Journal
• /
• v.55 no.2
• /
• pp.429-438
• /
• 2015

The objective of this paper is to obtain sharp upper bound for the second Hankel functional associated with the $k^{th}$ root transform $[f(z^k)]^{\frac{1}{k}}$ of normalized analytic function f(z) when it belongs to the class of starlike and convex functions with respect to symmetric points, defined on the open unit disc in the complex plane, using Toeplitz determinants.

• Structural Engineering and Mechanics
• /
• v.37 no.3
• /
• pp.285-296
• /
• 2011

The plane crack-contact problem for an infinite elastic layer with two symmetric rectangular rigid stamps on its upper and lower surfaces is considered. The elastic layer having an internal crack parallel to its surfaces is subjected to two concentrated loads p on its upper and lower surfaces trough the rigid rectangular stamps and a pair of uniform compressive stress $p_0$ along the crack surface. It is assumed that the contact between the elastic layer and the rigid stamps is frictionless and the effect of the gravity force is neglected. The problem is reduced to a system of singular integral equations in which the derivative of the crack surface displacement and the contact pressures are unknown functions. The system of singular integral equations is solved numerically by making use of an appropriate Gauss-Chebyshev integration formula. Numerical results for stress-intensity factor, critical load factor, $\mathcal{Q}_c$, causing initial closure of the crack tip, the crack surface displacements and the contact stress distribution are presented and shown graphically for various dimensionless quantities.