• Current Photovoltaic Research
• /
• v.10 no.4
• /
• pp.101-106
• /
• 2022

We prepared a CsPbI₂Br solution using Cesium iodide (CsI), Lead (II) bromide (PbBr₂) and Lead (II) iodide (PbI₂) materials into a polar solvent mixture of N,N-dimethylformamide (DMF) and Dimethyl sulfoxide (DMSO). A simple spin coating technique was used for the fabrication of CsPbI₂Br absorber layer in the solution process. In order to prepare uniform coating of absorber film we adopted a hot-air process in assocation with the spin coating. It was confirmed that the thin film manufactured by the hot-air process had a higher absorption rate than that without it, and the optical band gap was measured 1.93 eV. The thin film of absorber was uniformly prepared and revealed the Black α-Cubic crystal phase as proved through X-ray diffraction analysis. Finally, a perovskite solar cell having an n-i-p structure was manufactured with a CsPbI₂Br perovskite absorption layer. From the solar cell, we obtained a power conversion efficiency (PCE) of 5.97% in a forward measurement.

• Applied Science and Convergence Technology
• /
• v.24 no.4
• /
• pp.90-95
• /
• 2015

The adsorption behavior of tris (dimethylamino)-cyclopentadienyl-zirconium (Cp-Zr) precursor using an in-situ attenuated total reflectance-Fourier transform infrared spectroscopy (ATR-FT-IR) was studied. In attempt to improve the detection intensity of an adsorbed precursor, nanoparticles were uniformly distributed on the Ge ATR crystal surface employing the spray method. The absorption characteristics studies were carried out over the Ge crystal temperature in the range of $30{\sim}50^{\circ}C$. Upon increasing the temperature, a reduction of absorption was observed. Based on the peak intensities of ATR-FT-IR spectroscopy, higher-$ZrO_2$ absorption efficiency occurs when the nano-particles are utilized compared to pure Ge crystal.

• Composites Research
• /
• v.33 no.5
• /
• pp.256-261
• /
• 2020

In this study, the ignition temperature of the Al-Ti-C reaction system, the microstructure and the mechanical properties of the TiC/Mg composite which produced by the self-propagating high-temperature synthesis (SHS) followed by stir casting process were investigated. Mg based composite with uniformly dispersed 0, 10, 20, and 30 vol.% TiC were fabricated, and higher volume fraction of TiC reinforced composite showed superior compressive strength and wear resistance as compared with Mg matrix. It is attributed to the less contamination, defects, impurities in TiC/Mg composite by the in-situ SHS yield effective load transfer from the matrix to the reinforcement.

• Steel and Composite Structures
• /
• v.24 no.1
• /
• pp.65-77
• /
• 2017

The purpose of this research is to study the nonlinear free vibration and post-buckling analysis of functionally graded carbon nanotube reinforced composite (FG-CNTRC) beams resting on a nonlinear elastic foundation. Uniformly and functionally graded distributions of single walled carbon nanotubes as reinforcing phase are considered in the polymeric matrix. The modified form of rule of mixture is used to estimate the material properties of CNTRC beams. The governing equations are derived employing Euler-Bernoulli beam theory along with energy method and Hamilton's principle. Applying von $K\acute{a}rm\acute{a}n's$ strain-displacement assumptions, the geometric nonlinearity is taken into consideration. The developed governing equations with quadratic and cubic nonlinearities are solved using variational iteration method (VIM) and the analytical expressions and numerical results are obtained for vibration and stability analysis of nanocomposite beams. The presented comparative results are indicative for the reliability, accuracy and fast convergence rate of the solution. Eventually, the effects of different parameters, such as foundation stiffness, volume fraction and distributions of carbon nanotubes, slenderness ratio, vibration amplitude, coefficients of elastic foundation and boundary conditions on the nonlinear frequencies, vibration response and post-buckling loads of FG-CNTRC beams are examined. The developed analytical solution provides direct insight into parametric studies of particular parameters of the problem.

• International journal of advanced smart convergence
• /
• v.6 no.1
• /
• pp.57-67
• /
• 2017

In this paper, propose an algorithm to improve network lifetime by equally consuming energy of LEACH - Mobile sensor nodes. LEACH is one of energy efficient protocols. However, we did not consider the mobility of nodes. Therefore, the transmission reception success rate of the moving data is reduced. LEACH-Mobile is a protocol that has improved the drawbacks of these LEACH. However, since LEACH-Mobile has a larger number of data packets and consumes more energy than LEACH, it has a disadvantage that the lifetime of the network is short. In order to improvement these disadvantage, Based on the average of the remaining energy of the node, cluster heads are elected with a number of nodes whose energies are larger than the average of the remaining energy from the member nodes. After that, by trying to increase the lifetime of the network by equalizing the remaining energy. In to confirm whether improve the lifetime of the network, In this paper, the number of nodes and the position of all nodes are varied for each specific round, the rest energy is equalized, and the algorithm which uniformly selected the cluster head is compared with LEACH.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.23 no.1
• /
• pp.46-50
• /
• 2013

This paper proposes an adaptive fault accommodation control approach for flexible-joint (FJ) robots with multiple actuator faults. It is assumed that the value and occurrence time of multiple actuator faults are unknown. An adaptive fault accommodation control scheme with prescribed performance bounds, which characterize the convergence rate and maximum overshoot of tracking errors, is designed to accommodate the actuator faults. From the Lyapunov stability theorem, it is proved that all signals of the closed-loop system are semi-globally uniformly ultimately bounded and tracking errors are preserved within prescribed performance bounds regardless of actuator faults.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.31B no.2
• /
• pp.45-55
• /
• 1994

In this paper, a block based image approximation technique using the Self Affine System(SAS) from the fractal theory is suggested. Each block of an image is divided into 4 tiles and 4 affine mapping coefficients are found for each tile. To find the affine mapping cefficients that minimize the error between the affine transformed image block and the reconstructed image block, the matrix euation is solved by setting each partial differential coefficients to aero. And to ensure the convergence of coding block. 4 uniformly partitioned affine transformation is applied. Variable block size technique is employed in order to applynatural image reconstruction property of fractal image coding. Large blocks are used for encoding smooth backgrounds to yield high compression efficiency and texture and edge blocks are divided into smaller blocks to preserve the block detail. Affine mapping coefficinets are found for each block having 16$\times$16, 8$\times$8 or 4$\times$4 size. Each block is classified as shade, texture or edge. Average gray level is transmitted for shade bolcks, and coefficients are found for texture and edge blocks. Coefficients are quantized and only 16 bytes per block are transmitted. Using the proposed algorithm, the computational load increases linearly in proportion to image size. PSNR of 31.58dB is obtained as the result using 512$\times$512, 8 bits per pixel Lena image.

• The Journal of Natural Sciences
• /
• v.9 no.1
• /
• pp.57-60
• /
• 1997

Let {$X_{ni}$,1$\leq$i$\leq$,n$\geq$1} be an array of rowwise independent B-valued random variables which is uniformly bounded by a random various X satisfying $E|X|^{2p}<\infty$ for some p$\geq$1. Let {$a_{ni}$,1$\leq$i$\leq$,n$\geq$1} be an array of constants. Under some auxiliary conditions on {$a_{ni}$}, it is shown that $sum_{i=1}^n a_{ni}X_{ni}\rightarrow0$ in probability if and only if $sum_{i=1}^n a_{ni}X_{ni}$ converges completely ot 0.

• Structural Engineering and Mechanics
• /
• v.64 no.5
• /
• pp.591-610
• /
• 2017

This paper is concerned with the static analysis of variable thickness of two directional functionally graded porous materials (FGPM) circular plate resting on a gradient hybrid foundation (Horvath-Colasanti type) with friction force and subjected to compound mechanical loads (e.g., transverse, in-plane shear traction and concentrated force at the center of the plate).The governing state equations are derived in terms of displacements based on the 3D theory of elasticity, assuming the elastic coefficients of the plate material except the Poisson's ratio varying continuously throughout the thickness and radial directions according to an exponential function. These equations are solved semi-analytically by employing the state space method (SSM) and one-dimensional differential quadrature (DQ) rule to obtain the displacements and stress components of the FGPM plate. The effect of concentrated force at the center of the plate is approximated with the shear force, uniformly distributed over the inner boundary of a FGPM annular plate. In addition to verification study and convergence analysis, numerical results are displayed to show the effect of material heterogeneity indices, foundation stiffness coefficients, foundation gradient indices, loads ratio, thickness to radius ratio, compressibility, porosity and friction coefficient of the foundation on the static behavior of the plate. Finally, the responses of FG and FG porous material circular plates to compound mechanical loads are compared.

• Applied Science and Convergence Technology
• /
• v.23 no.3
• /
• pp.134-138
• /
• 2014

One-dimensional nanostructures such as nanowires have been extensively investigated as a promising type of material for applications of nanoscale technology. The fabrication of single-nanowire devices are consequently important and interesting. This study introduced a feasible method for growing CuO nanowires on Cu foils. The nanowires had diameters of 10~150 nm and lengths of more than $7{\mu}m$ and were grown by means of thermal oxidation in a vacuum. They were entirely and uniformly grown over the Cu foil surfaces and could be extracted and dispersed in an ethanol solution for further purposes. In addition, a simple fabrication method for realizing device functionality from a single CuO nanowire was reported. Fabricated devices were carefully checked by field-emission scanning electron microscopy (SEM). The probability of the realization of a single-CuO-nanowire device relative to that of all other types was estimated to be around 25%. Finally, the I-V characteristics of the devices were analyzed.