• Journal of Bio-Environment Control
• /
• v.12 no.1
• /
• pp.12-16
• /
• 2003

The effect of humidifying methods on the mean size of droplets ejected from humidifier and distributions of relative humidity in a graft-taking enhancement system (GTES) was investigated. The mean sizes of droplets ejected from an ultrasonic humidifier and a steam humidifier with electrodes were 7.58$\pm$0.14 and 9.01$\pm$0.06 $\mu$m, respectively. Assuming that the particles ejected from humidifiers were mutually combined with distance, the mean diameter of droplets became larger as the distance apart from the outlet of humidifiers increased. When the relative humidity in GRS was controlled at 90％ using the ultrasonic humidifiers, the average relative humidity at the height of 0.4, 1.1 and 1.8 m were 92.1$\pm$5.3, 90.9$\pm$5.6, and 89.7$\pm$6.8%, respectively. However, the average relative humidity using the steam humidifier with electrodes showed 93.4 $\pm$5.4, 90.7$\pm$5.9, and 89.3$\pm$7.0%, respectively. Therefore, it was concluded that humidification by ultrasonic humidifier would be appropriate for the uniform distribution of relative humidity in GTES.

• Journal of Biomedical Engineering Research
• /
• v.21 no.4
• /
• pp.403-409
• /
• 2000

This paper is about to simulate the defibrillation situations using 3D FE(finite element) thorax model and describes the effects of three clinical electrodes' positions and size and organ's resistivity used in simulation on the characteristics of current density distribution over myocardium. The model was constructed with a eillipsoidal cylinder for the thorax and the 2D Visible Human images for remains. And, the distributions of current density were computed by a commercial program ANSYS 5.4. The electrical shock of the AP(anterior-posterior ) electrode provided more current flows with heart than the others and that of the LL(lateral-lateral) electrode showed the most uniform current density distribution. However, the electrode size had little effect on the current density distribution. In the evaluation of model's sensitivity to tissue resistivity variation, the variation of the myocardium's resistivity most affected the minimum, average and maximum current densities.

• Journal of the Korean earth science society
• /
• v.39 no.6
• /
• pp.575-592
• /
• 2018

This study investigates the formation mechanism of columnar joints at the Sanin Kaigan Geopark in Japan based on its morphology, rock type and igneous structure. Columnar joints distribute to five areas of three prefectures. That is, Kyogasaki, Byobuiwa, Tateiwa and Kyugenkado in Kyotango area of Kyoto prefecture; Genbudo and Kinumaki Shrine in Toyooka City of Hyogo prefecture; Yoroinosode, Takanosushima, Mini-Yoroinosode in Kamicho Town of Hyogo prefecture; Miooshima and Nagasakihana, Shitaara Domon, Kuzakuishi, Moroyose dyke in Shinonsencho Town of Hyogo prefecture; Shirawara dyke in Iwamicho Town in Tottori prefecture. Igneous structures are divided into three types: lava flow, sill and dyke. Lithologies are divided into five types including basalt, andesite, dacite, rhyolite, and quartz porphyry. Lava flow shows colonnade and entablature. However, entablature is not seen in the sills and dykes in the area. Although the polygons of columnar joint vary from tetragon to octagon, hexagon is most frequently found. The width of colonnades ranges from 10cm to 1m, but their size does not correlate with its $SiO_2$ contents. Meanwhile, their size and morphology at single site are comparatively uniform.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.41 no.2
• /
• pp.77-83
• /
• 2021

Rye (Secale cereal L.) is the most tolerant to abiotic stress including low temperature, drought, and unfavorable soil conditions among the winter cereals. Rye is the rapid growth of early spring results from increasing areas for the use of the forage and green manure in the middle part of Korea. "Jungmo2509", a rye cultivar was developed by the National Institute of Crop Science (NICS), RDA in 2014. It was developed from a cross between "Olhomil", a self-compatible cultivar, and "Synthetic II", a self-incompatible line. "Jungmo2509" is an erect plant type and of a middle size, with a green leaf color, a yellowish-white colored culm, and a yellowish brown-colored, small-size grain. The heading date of "Jungmo2509" was April 23, which was 5 days later than that of "Gogu", respectively. But "Jungmo2509" showed greater resistance to lodging compared to that of the check cultivar, with similar to winter hardiness, wet injury, and disease resistance. "Jungmo2509" was a higher to than "Gogu" in terms of protein content (9.4% and 8.0%, respectively), total digestible nutrients (TDN) (55.7% and 55%, respectively). The seed productivity of "Jungmo2509" was approximately 2.08 ton 10a-1, which was 11% lower than that of the check. Almost all rye cultivars are out-crossing due to genes controlling incompatibility, but "Jungmo2509" is higher seed fertility (56%) than that of Gogu (0%). it has self-compatible genes. "Jungmo2509" is erect in plant type and resistance for lodging. Therefore, "Jungmo2509" can produce uniform seeds for processed grains of human consumption and utilize them as parents for breeding the rye hybrids with high forage yields.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.33 no.5
• /
• pp.167-173
• /
• 2023

Li₃V₂(PO₄)₃ and Li₃V₂(PO₄)₃/C composite with single phase monoclinic structure for the cathode materials are successfully synthesized by direct co-precipitation method using N₂H₄·H₂O as the reducing agent and alginic acid as the carbon source, and their electrochemical properties were compared. The particles with approximately 1~2 ㎛ size and the uniform spherical-like morphology of the narrow particle size distribution were obtained. In addition, the residual carbon can also improve the electrical conductivity. The Li₃V₂(PO₄)₃/C composite has improved initial specific discharge capacity and excellent cycle characteristics to maintain capacity stably than Li₃V₂(PO₄)₃. The results indicate that the reducing agent and carbon composite can affect the good crystallinity and electrochemical performance of the cathode materials.

• Journal of Bio-Environment Control
• /
• v.23 no.4
• /
• pp.293-302
• /
• 2014

This study was carried out to develop rain shelter which can make an appropriate size and environment for Chinese cabbage rainproof cultivation. Fifty three farms with chinese cabbage rainproof cultivation system have been investigated to set up width and height of rain shelter. Mostly the width of 6m was desired for rain shelter and the height of 1.6m for their eaves, so these values were chosen as the dimensions for rain shelter. After an analysis of their structural safety and installation costs by the specifications of the rafter pipe, Ø$25.4{\times}1.5t$ and 90cm have been set as the size of rafter that such size costs the least. This size is stable with $27m{\cdot}s^{-1}$ of wind velocity and 17cm of snow depth. Therefore it is difficult to apply this dimension to area with higher climate load. In order to sort out such problem, the rain shelter has been designed to avoid damage on frame by opening plastic film to the ridge. Once greenhouse band is loosen by turning the manual switch at the both sides of rain shelter and open button of controller is pushed then switch motor rises up along the guide pipe and plastic film is opened to the ridge. Chinese cabbage can be damaged by insects if rain shelter is opened completely as revealed a field. To prevent this, farmers can install an insect-proof net. Further, the greenhouse can be damaged by typhoon while growing Chinese cabbage therefore the effect of an insect-proof net on structural safety has been analyzed. And then structural safety has been analyzed through using flow-structure interaction method at the wind condition of $40m{\cdot}s^{-1}$. And it assumed that wind applied perpendicular to side of the rain shelter which was covered by insect-proof net. The results indicated that plastic film was directly affected by wind therefore high pressure occurred on the surface. But wind load on insect-proof net was smaller than on plastic film and pressure distribution was also uniform. The results of structural analysis by applying pressure data extracted from flow analysis indicated that the maximum stress occurred at the end of pipe which is the ground part and the value has been 54.6MPa. The allowable stress of pipe in the standard of structural safety must be 215 MPa or more therefore structural safety of this rain shelter is satisfied.

• Korean Chemical Engineering Research
• /
• v.44 no.5
• /
• pp.505-512
• /
• 2006

Characteristics of particle holdup and heat transfer were investigated in a liquid-particle swirling fluidized bed whose diameter was 0.102 m and 2.5 m in height. Effects of liquid velocity, particle size and swirling liquid ratio($R_s$) on the particle holdup and immersed heater-to-bed overall heat transfer coefficient were examined. The particle holdup increased with increasing particle size and swirling liquid ratio but decreased with increasing liquid velocity.The local particle holdup was relatively high in the region near the heater when the $R_s$ value was 0.1~0.3, but the radial particle holdup was almost uniform when the $R_s$ value was 0.5, whereas, when the $R_s$ value was 0.7, the local particle holdup was relatively low in the region near the heater. The heat transfer characteristics between the immersed heater and the bed was well analyzed by means of phase space portraits and Kolmogorov entropy(K) of the time series of temperature difference fluctuations. The phase space portraits of temperature difference fluctuations became stable and periodic and the value of Kolmogorov entropy tended to decrease with increasing the value of $R_s$ from 0.1 to 0.5. The Kolmogorov entropy exhibited its maximum value with increasing liquid velocity. The value of overall heat transfer coefficient(h) showed its maximum value with the variation of liquid velocity, bed porosity or swirling liquid ratio, but it increased with increasing particle size. The value of K exhibited its maximum at the liquid velocity at which the h value attained its maximum. The particle holdup and overall heat transfer coefficient were well correlated in terms of dimensionless groups of operating variables.

• Journal of Aquaculture
• /
• v.11 no.1
• /
• pp.11-17
• /
• 1998

Variations of hepatocyte in the larval liver of grouper, Epinephelus akaara wre examined to understand the effect of starvation during the first feeding period, 3 to 5 days after hatching. Total length of the fed larvae increased from the 5th day after hatching, although no significant difference between the fed and starved larvae was found untill the 4th day after hatching. Survival rate of the starved larvae decreased from the 4th day after hatching, and almost all of the larvae died by the 5th day after hatching. Nuclear size of hepatocyte in the starved larvae starterd to decrease from the 4th day after hatching. The sizes by 4th and 5th days after hatching in the starved larvae were 1.4 to 1.9 times smaller than those in the fed ones. Hepatocytes in the starved larvae showed irregular morphology in which the nuclei were irregularly shrunk and highly compacted from the 4th day, while hepatocyte nuclei in the fed ones maintained their uniform features during the whole experimental period. These results implied that the initial larval food should be supplied at least within the 4th day after hatching. Also, it suggested that the size of hepatocyte nucleus might be and indicator of starvation for wild and cultured grouper larvae.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.10 no.1
• /
• pp.115-123
• /
• 1990

The purpose of this study was to examine the uses of coal ash as a type of construction material. The methods of examination were chemical anlysis, soil laboratory test and the soil vibration test. Materials used were coal ash obtained as a by-product from 5 thermal power plants in Yongdong, Yongwol, Sochon(anthracite coal) and in Samchonpo and Honam (bituminous coal). Over 70% of the coal ash consisted of silica and alumina. The fly ash grain size showed a uniform distribution from fine-sand to silt, and that of the bottom ash showed from sand to gravel. The specific gravity and density of the coal ash were low. The long term strength increased gradually due to the self-setting property resulting from pozzolanic activity. The shear strength was higher than that of general soil. Cohesion and optimum moisture content of anthracite coal ash were higher than bituminous coal ash, whereas the maximum dry density was higher in bituminous coal ash. The coal ash dynamic Young's modulous curve range was similar to that of general soil. Of the results from the soil vibration test by car-running, the size relative acceleration level in the ash pond was higher than that of natural ground, but the damping ratio was lower than that of natural ground near the ash pond. The coal ash has more advantageous engineering properties than general soil with particles of the same size. For example, the California Bearing Ratio of the bottom ash at both Yongdong and Yongwol was 77~137%. Therefore we expect that if further study is done, coal ash can be used as a construction material when reclaiming seashore, construction embankments, road construction, making right-weight aggregate, or as a general construction material.

• The Journal of Korean Academy of Prosthodontics
• /
• v.46 no.2
• /
• pp.185-192
• /
• 2008

Purpose: This study was designed to investigate the fitness of adjustable dental impression trays on the Caucasian and African American. Material and methods: The size and shape of these trays were designed from the results of the dental arch size of Korean adults. Tray samples were made by CAD-CAM working. Sixty Caucasian (male:30, female:30) and sixty African American (male:30, female:30) were selected for taking irreversible hydrocolloid impression using these trays. The author measured the width and length of impression material on the several measuring points. Results: 1. Uniform impression material width was achieved by controling the width of the tray using stops and beveled guides. 2. In the maxillary tray on the Caucasian, the impression material thickness was measured to be rather great showing thickness of the midpalatal part 13.0 mm. 3. In the maxillary tray on the African American, the impression material thickness was measured to be rather great showing thickness of the midpalatal part 12.0 mm, posterior palatal part 11.0 mm and the labial frenum width was 11.0 mm. 4. In the maxillary tray on the African American, the impression material width of posterior border (0.8 mm) was measured to be small. 5. In the mandibular tray on the Caucasian, the impression material width was measured (2.7-6.7 mm) and posterior border width (2.1 mm) was measured small. The impression material length was measured (2.8-6.7 mm). 6. In the mandibular tray on the African American, the impression material width was measured to be rather great showing width of the labial frenum 9.2 mm and the width of posterior border was measured too small (0.3 mm). Conclusion: This adjustable dental tray shows good accuracy to Korean because it was designed by the analysis of the dental arch size of Korean adult model. With this result, it can be applied to Caucasian and African American, we can take more easy and accurate dental impressions.