• 한국지반공학회논문집
• /
• 제35권5호
• /
• pp.21-30
• /
• 2019

얕은 터널에 대한 연구는 종방향 하중전이와 수평지반에 대한 연구가 주를 이루었으며 사면 하부에 위치한 얕은 터널 주변지반의 거동연구는 미흡한 실정이다. 따라서 본 연구에서는 사면 하부에 위치한 터널의 종방향 굴진에 따른 터널 주변지반의 거동을 규명하기 위해 변위제어방식으로 모형시험을 실시하였다. 모형터널은 폭 320mm, 높이 210mm, 길이 55mm 규격의 강성이 큰 알루미늄 강체로 제작하였고, 모형지반은 3가지 규격의 탄소봉을 혼합하여 균질한 모형지반을 조성하였다. 모형시험은 사면 경사와 토피고를 변수로 측벽변형을 발생시키는 변위제어방식으로 실시하였으며, 터널 벽체의 하중변화, 터널 주변지반의 하중전이와 지표침하 변화를 측정하고 분석하였다. 지표침하의 변화는 경사가 증가할수록 수평지반보다 20~39%의 증가가 나타났다. 터널 천단부 및 측벽부의 하중 변화는 사면 경사가 증가할수록 천단부는 최대 20%가 증가하고, 측벽부는 사면 경사의 영향으로 하중비가 감소하는 것을 확인하였다. 연직하중은 토피고가 1.0D 이하에서는 최대 128%의 하중증가가 나타났지만, 토피고가 1.5D 이상에서는 수평지반과 큰 차이가 나타나지 않았다. 이것으로 사면 경사는 토피고 1.0D에서 가장 큰 영향이 나타나는 것을 확인하였다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제8권1호
• /
• pp.195-202
• /
• 2004

일반적으로 쉘 표면에 수직한 압력은 변형 전 쉘 표면에 수직한 방향으로 작용한다고 가정하고 쉘 표면의 변형으로 인한 표면적의 변화를 고려하지 않음으로써 이에 의한 변형에너지를 무시한다. 그러나, 변형된 쉘 표면에 수직으로 작용하는 압력은 고유진동수와 좌굴하중에 큰 영향을 미칠 수 있다. 본 연구에서는 구조물의 변형에 의한 쉘 단면적의 변화와 압력의 방향변화에 대한 변형에너지를 구하고 이를 변분하여 부가매트릭스를 산정하였다. 이를 축대칭요소에 추가하여 전산구조해석을 통해 외압의 부가효과를 고려한 고유진동수를 계산하였다. 외압의 크기가 증가함에 따라 쉘 구조물의 고유진동수는 감소하며, 고유진동수가 영이 될 때의 외압의 크기를 좌굴하중으로 볼 수 있다. 이를 이용하여 정해가 존재하는 원통 쉘에 적용한 결과 유사한 해를 얻을 수 있었으며, 부가효과를 고려하지 않았을 경우는 상당한 차를 나타내었다. 그러나, 반구형 돔에서는 원통 쉘에 비해 압력의 부가효과가 거의 나타나지 않는 것으로 나타났다.

• Geomechanics and Engineering
• /
• 제9권5호
• /
• pp.631-644
• /
• 2015

This article considers the problems of cylindrical bending of functionally graded plates in which material properties vary through the thickness. The variation of the material properties follows two power-law distributions in terms of the volume fractions of constituents. In addition, this paper considers orthotropic materials rather than isotropic materials. The traction-free condition on the top surface is replaced with the condition of uniform load applied on the top surface. Numerical results are presented to show the effect of the material distribution on the deflections and stresses. Results show that, all other parameters remaining the same, the studied quantities (stress, deflection) of P-FGM and E-FGM plates are always proportional to those of homogeneous isotropic plates. Therefore, one can predict the behaviour of P-FGM and E-FGM plates knowing that of similar homogeneous plates.

• Structural Engineering and Mechanics
• /
• 제24권2호
• /
• pp.155-180
• /
• 2006

Many applications in mechanical design involve elastic bodies coming into contact under the action of the applied load. The distribution of the contact pressure throughout the contact interface plays an important role in the performance of the contact system. In many applications, it is desirable to minimize the maximum contact pressure or to have an approximately uniform contact pressure distribution. Such requirements can be attained through a proper design of the initial surfaces of the contacting bodies. This problem involves a combination of two disciplines, contact mechanics and shape optimization. Therefore, the objective of the present paper is to develop an integrated procedure capable of evaluating the optimal shape of contacting bodies. The adaptive incremental convex programming method is adopted to solve the contact problem, while the augmented Lagrange multiplier method is used to control the shape optimization procedure. Further, to accommodate the manufacturing requirements, surface parameterization is considered. The proposed procedure is applied to a couple of problems, with different geometry and boundary conditions, to demonstrate the efficiency and versatility of the proposed procedure.

• Coupled systems mechanics
• /
• 제13권2호
• /
• pp.171-186
• /
• 2024

In the present paper, thermal buckling characteristics of functionally graded rectangular plates made of porous material that are integrated with surface-bonded piezoelectric actuators subjected to the combined action of thermal load and constant applied actuator voltage are investigated by utilizing a Navier solution method. The uniform temperature rise loading is considered. Thermomechanical material properties of FGM plates are assumed to be temperature independent and supposed to vary through thickness direction of the constituents according to power-law distribution (P-FGM) which is modified to approximate the porous material properties with even and uneven distributions of porosities phases. The governing differential equations of stability for the piezoelectric FGM plate are derived based on higher order shear deformation plate theory. Influences of several important parameters on the critical thermal buckling temperature are investigated and discussed in detail.

• 한국태양에너지학회 논문집
• /
• 제31권6호
• /
• pp.132-138
• /
• 2011

Inducing the natural lighting into building has been commonly applied to the spaces where artistic objects are displayed to create better visual environment for the appreciation. The direct natural lighting, especially through top lighting system may, however, bring forth discoloing of highly light-sensitive materials such as paintings or demanding additional cooling load. In addition, it causes to create glare against appreciators or to yield in visual distraction due to the extreme contrast on the inner surfaces of the spaces. Shading device such as louver is capable of preventing such voidable cases with careful manipulation. This study aims to provide basic design guide-line when the flat-form louver has to be applied to top lighting system. Interaction between the daylight and louver was simulated by Reluxpro program with variation of the attachment location, the angle of the lover, surface reflectivity, to obtain the illumination of the floor surface. This study yields the louver just under the top lighting window with 90 degree angle gives the most desirable way of employment when the uniform illumination on the floor surface is required.

• Tribology and Lubricants
• /
• 제23권6호
• /
• pp.306-311
• /
• 2007

This paper presents the friction characteristics of pb-fres pin bushing bearings for an automotive gasoline engine. The external load is 100 N to 600 N and the speed of the pin bushing bearing is 1000 rpm to 3000 rpm against the rubbing surfaces. And the contact modes of rubbing surfaces between a piston pin and a pb-free pin bushing specimen are a dry friction, an oil lubricated friction and a mixed friction that is starved by a lack of engine oil. Two influential factors of a contact rubbing modes and a material property are very important parameters on the tribological performance of a friction characteristic between a piston pin and a pb-free pin bushing. The experimental result shows that the pin bushing speed of 2000 rpm shows a typical oil film lubricated sliding contact mode in which means that as the applied load is increased, the friction loss is increasing. But other contact mode depending on the speed and the load may affect to the fiction coefficient without a regular and uniform trend. In summary, the oil lubricated rubbing surface definitely decreases a running-in period in short and increase oil film stiffness, and this may leads the reduction of a friction loss.

• Structural Engineering and Mechanics
• /
• 제62권5호
• /
• pp.595-606
• /
• 2017

During their life span, post-tensioned concrete structures may be exposed to thermal loads. Therefore, there has been a growing interest in research on the advanced analysis and design of post-tensioned concrete slabs subjected to thermal loads. This paper investigates the structural behaviour of post-tensioned one-way spanning concrete slabs. A nonlinear finite element model for the analysis of post- tensioned unbonded and bonded concrete slabs at elevated temperatures was developed. The interface between the tendon and surrounding concrete was also modelled, allowing the tendon to retain its profile shape during the deformation of the slab. The load-deflection behaviour, load-force behaviour in the tendon, and the failure modes are presented. The numerical analysis was conducted by the finite element ANSYS software and was carried out on two different one-way concrete slabs chosen from literature. A parametric study was conducted to investigate the effect of several selected parameters on the overall behavior of post-tensioned one-way concrete slab. These parameters include the effect of tendon bonding, the effect of thermal loading and the effect of tendon profile. Comparison between uniform thermal loading and nonuniform thermal loading showed that restrained post tensioned slab with bottom surface hotter has smaller failure load capacity.

• 대한치과보철학회지
• /
• 제29권2호
• /
• pp.177-194
• /
• 1991

The purpose of this study was to analyze the magnitude and distribution of stress using a photoelastic model from a distal extension removable partial dentures with three kinds of mandibular major connectors, that is, lingual bar, linguoplate, and swing-lock attachment. A photoelastic model was made of the epoxy resin(PC-1) and hardener(PCH-1) and coated with plastic cement-1 (PC-1) at the lingual surface of the epoxy model and set with three kinds of chrome-cobalt removable partial dentures. A bilateral vertical load of 15kg to the middle portion of the metal bar crossing both the first molars of the right and the left, and a unilateral vertical load of 12.5kg to the right first molar were applied with the use of specially designed loading device and the reflective circular polariscope was used to analyze the photoelastic model under each condition. The following results were obtained : 1. When the bilateral vertical load was applied, the magnitude and distribution of the stress concentration of the edentulous area and the terminal abutment or adjacent teeth was in the order of lingual bar, linguoplate, swing-lock attachment. 2. When the unilateral vertical load was applied, the magnitude and distribution of the stress concentration of the edentulous area and the terminal abutment or adjacent teeth was in the order of lingual bar, linguoplate, swing-lock attachment. 3. When the unilateral vertical load was applied, the magnitude and distribution of the stress concentration of the termial abutment or adjacent teeth on the non-loaded side showed the least stress distribution in case of swing-lock attachment. 4. When the bilateral vertical load and the unilateral vertical load were applied the swing-lock attachment showed the mildest uniform stress distribution on the edentulous area and the alveolar bone around the abutment teeth.

• 한국물환경학회지
• /
• 제31권6호
• /
• pp.653-664
• /
• 2015

TPLMS (Total water pollutant load management system) that is the most powerful water-quality protection program have been implemented since 2004. In the implementation of TPLMS, target water-quality and permissible discharged load from each unit watershed can be decided by water-quality modeling. And NPS (Non-point sources) discharge coefficients associated with certain (standard) flow are used on estimation of input data for model. National Institute of Environmental Research (NIER) recommend NPS discharge coefficients as 0.15 (Q₂₇₅) and 0.50 (Q₁₈₅) in common for whole watershed in Korea. But, uniform coefficient is difficult to reflect various NPS characteristics of individual watershed. Monthly NPS discharge coefficients were predicted and estimated using surface flow and water-quality from HSPF watershed model in this study. Those coefficients were plotted in flow duration curve of study area (Palger stream and Geumho C watershed) with monthly average flow. Linear regression analysis was performed about NPS discharge coefficients of BOD, T-N and T-P associated with flow, and R² of regression were distributed in 0.893~0.930 (Palger stream) and 0.939~0.959 (Geumho C). NPS Discharge coefficient through regression can be estimated flexibly according to flow, and be considered characteristics of watershed with watershed model.