• Journal of the Korean Institute of Rural Architecture
• /
• v.2 no.2
• /
• pp.115-126
• /
• 2000

Retaining walls are used to prevent excessive movement of retained soils. Typical retaining walls include gravity, reinforced concrete, reinforced earth and tie-back. However, from a practical viewpoint there are still drawbacks among these often constructed retaining walls. New types of retaining walls constructed with precast concrete blocks are proposed. This type of retaining wall is incorporates each blocks interconnected with adjacent block by connecting unit to build up a flexible retaining-wall system. This paper focus to behavior characteristics includes deformation and distribution of lateral earth pressure by loading tests and FEM analysis. For model tests, a 1/10 scale reduce models are manufactured include unevenness part, drainage hole and connecting unit and steel wire used to connect each blocks with adjacent block. To simulate the real retaining walls closely, uneven parts are interconnected each other and the construction type of blocks and wall front inclination are varied to investigate the relative displacement of individual block and the location of maximum deformation of wall as increasing surcharging. Additionally, PENTAGON3D, which solve the geotechnical and other problem, used for verifying and comparing with model tests.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.3
• /
• pp.100-107
• /
• 2001

The main goals of the automotive suspension systems are to isolate roadway unevenness from the tire and to improve vehicle stability. To overcome the performance limitation of the passive systems the active systems which completely replace the passive spring and damper elements with a force generating actuator has been studied. However, application of the system has been limited because it has required a significant amount of power. Recently, alternative systems which retain passive elements but include active elements have been developed to reduce the power required. Those systems are mostly focused on the control system which compresses the spring-damper directly. In this study, a new type of power efficient control system which makes the spring-damper unit slide in side way is studied. After constructing the control system including dynamic modeling and motion control, two types of alternative control systems are compared in view of power consumption and dynamic attitudes such as roll responses as well as heave responses. Also, a half car bond graph model is developed to show clearly the significant differences in performances between two control systems.

• Coupled systems mechanics
• /
• v.3 no.2
• /
• pp.147-170
• /
• 2014

In the recent times, dimensions of heavy load carrying vehicle have changed significantly incorporating structural flexibility in vehicle body. The present paper outlines a procedure for the estimation of bridge response statistics considering structural bending modes of the vehicle. Bridge deck roughness has been considered to be non homogeneous random process in space. Influence of pre cambering of bridge surface and settlement of approach slab on the dynamic behavior of the bridge has been studied. A parametric study considering vehicle axle spacing, mass, speed, vehicle flexibility, deck unevenness and eccentricity of vehicle path have been conducted. Dynamic amplification factor (DAF) of the bridge response has been obtained for several of combination of bridge-vehicle parameters. The present study reveals that flexible modes of vehicle can reduce dynamic response of the bridge to the extent of 30-37% of that caused by rigid vehicle model. However, sudden change in the bridge surface profile leads to significant amount of increment in the bridge dynamic response even if flexible bending modes remain active. The eccentricity of vehicle path and flexural/torsional rigidity ratios plays a significant role in dynamic amplification of bridge response.

• Journal of The Institute of Information and Telecommunication Facilities Engineering
• /
• v.8 no.2
• /
• pp.90-95
• /
• 2009

All-optical fiber-type gain flattening filer (GFF) for an EDFA (Erbium doped fiber amplifier) were fabricated by using a FBT (fiber biconical tapered) process and the performance of the GFF was tested and athermal package was proposed. Historically, the chief contributor to gain unevenness has been the EDFA. Due to the inherent gain response of the EDFA's operation, there is always a modest imbalance in the gain applied as a function of wavelength. FBT methods have been used to make fiber type couplers and WDM filter since 1980. Attractivity of this methods was simple, cost effective and thermal stability. Simulation program tool is made to design target GFF profile for this paper. Fiber coupler manufacturing machine is modified for the GFF process. The final GFF is obtained by cascading 4 unit filter that has 6 taper stage. Test result shows 1 dB of wavelength flatness in the C band. Polarization dependent loss is under 0.15dB. The center wavelength variation is below ${\pm}$0.35nm at the temperature range of $20^{\circ}C$ to $70^{\circ}C$.

• Design & Manufacturing
• /
• v.10 no.2
• /
• pp.24-28
• /
• 2016

In this study, relevant to impact extrusion process of the rectangular batter case for electric vehicles, numerical and experimental analyses were conducted to reduce the earring defects induced in the unevenness of metal flow. Since the earring is caused by the non-uniform metal flow induced in the friction and aspect ratio in the bottom section. As a way to reduce the earring, variable land die concept was applied. In order to analyze numerically the complex metal flow by using commercial finite element package, DEFORM 3D, impact extrusion process was simplified in upsetting mode at bottom section and extrusion mode at land section. The impact extrusion experiments were conducted to verify the assessment of process parameter for impact extrusion. As results, variable land die which has longer longitudinal section makes reduce earring defects. In addition, it was confirmed that the effect that slug shape like dog-bone also can reduce the earring. This study is expected to be able to present the useful design guidelines for manufacturing the battery case.

• Journal of Biosystems Engineering
• /
• v.27 no.2
• /
• pp.79-88
• /
• 2002

This study was conducted to develop system for high speed rice transplanting machines. The control system includes a sensor detecting the tilt angle of the seedling bed, a micro-controller and a hydraulic system consisting of a double acting cylinder, a four-way three-position solenoid valve, a relief valve and a hydraulic pump. The levelling system shared the pump with the existing steering control, resulting in a tandem center circuit for the steering and levelling control systems. Using the input signal from the sensor, the micro-controller determined and generated the output signal to control the cylinder through the solenoid valve to keep the seedling bed always parallel to the water surface regardless of soil unevenness during the transplanting operations. Both an ON/OFF and a PWM control schemes were tested. When the flow rate was more than 1 ι/min in the ON/OFF control, the system showed unstable rolling. However, in the PWM control, the system worked stably although the flow rate was more than 1 ι/min. The PWM control showed a better performance when a large difference between the angle and the dead band of the control system occurred. The characteristics of tile system response to given tilt angles were predicted by a computer simulation. Both the ON/OFF and the PWM control systems worked well providing that the operating and waiting times were properly adjusted.

• Structural Engineering and Mechanics
• /
• v.74 no.3
• /
• pp.407-423
• /
• 2020

The pre-peak cyclic shear mechanism of two-order asperity degradation of rock joints in the direct shear tests with static constant normal loads (CNL) are investigated using experimental and numerical methods. The laboratory testing rock specimens contains the idealized and regular two-order triangular-shaped asperities, which represent the specific geometrical conditions of natural and irregular waviness and unevenness of rock joint surfaces, in the pre-peak cyclic shear tests. Three different shear failure patterns of two-order triangular-shaped rock joints can be found in the experiments at constant horizontal shear velocity and various static constant normal loads in the direct and pre-peak cyclic shear tests. The discrete element method is adopted to simulate the pre-peak shear failure behaviors of rock joints with two-order triangular-shaped asperities. The rock joint interfaces are simulated using a modified smooth joint model, where microscopic scale slip surfaces are applied at contacts between discrete particles in the upper and lower rock blocks. Comparing the discrete numerical results with the experimental results, the microscopic bond particle model parameters are calibrated. Effects of cyclic shear loading amplitude, static constant normal loads and initial waviness asperity angles on the pre-peak cyclic shear failure behaviors of triangular-shaped rock joints are also numerically investigated.

• Structural Engineering and Mechanics
• /
• v.81 no.1
• /
• pp.69-79
• /
• 2022

The dynamic responses of a pier-pile-soil system subjected to a barge/flotilla collision are analyzed. A coupled high-speed train and bridge system with a damaged pier after barge/flotilla collision is established by taking the additional unevenness of the track induced by the damaged pier as the self-excitation of the system. The whole process of a CRH2 high-speed train running on the 6×32 m simply-supported PC (prestressed concrete) box-girder bridge with a damaged pier is simulated as a case study. The results show that the lateral displacements and accelerations of the bridge with a damaged pier are much greater than the ones before the collision. The running safety indices of the train increase with the train speed as well as with the number of barges in the flotilla. In flotilla collision, the lateral wheel/rail forces of the train exceed the allowable values at a certain speed, which influences the running safety of the trains.

• World Technopolis Review
• /
• v.1 no.3
• /
• pp.192-205
• /
• 2012

Globalization has fuelled the desire for simplicity and flexibility in rules and processes within nations. de Soto (2000) calls for the simplification of rules to enable people to join the formal economy. Friedman (2005) echoes the need for simpler rules, to attract business and capital. Market-based approaches to governing have been adopted in many nations due to globalization. Recent developments demonstrate that such approaches fail. Globalization may lead to impoverishment in the absence of proper forms of governance (Cooney 2000). That is why it has the tendency to become a "race to the bottom." Regulatory measures can be costly, and the costs of doing business are uneven across nations. This unevenness is being used as a comparative advantage. Others call this regulatory competition (Smith-Bozek 2007) or competitive governance (Schachtel and Sahmel 2000), which is similar to the model of Charles Tiebout. Collaborative governance is an approach that governments could use in lieu of the competitive method. Mechanisms that enable stakeholders to exchange information, harmonize activities, share resources, and enhance capacities (Himmelman 2002) are needed. Philippine public policy encourages a shift in modes of realizing labor market governance outcomes from command to collaboration (Sale and Bool 2010B; Sale 2011). Is labor market governance and regional development in the Philippines collaborative? Or is the opposite - competitive governance (Tiebout model) - more evident? What is the dominant approach? This preliminary research tackles these questions by looking at recent data on average and minimum wages, wage differentials, trade union density, collective bargaining coverage, small and bigger enterprises, employment, unemployment and underemployment, inflation, poverty incidence, labor productivity, family income, among others, across regions of the country. The issue is studied in the context of legal origins. Cultural explanations are broached.

• Food Science and Preservation
• /
• v.21 no.6
• /
• pp.838-843
• /
• 2014

In this study, near-infrared spectroscopy was used to observe the drying non-uniformity of vegetables such as spring onions, onions, and garlic, which are commonly used for seasoning. For the warm-air convection drying method, the vegetables showed drying non-uniformity, which is due to the unevenness of the wind temperature and humidity depending on the height and position of the drying tray. The second derivative spectra between the vegetable samples with different drying degrees were compared. The peak at around 1,390~1,400 nm, which is assigned to weak hydrogen bonds of water, was changed during drying whereas the peak near 1,420 nm, which represents strong hydrogen (H-) bonds of water, was not changed, indicating that water with weak H-bonds evaporates first during drying, and that water with strong H-bonds remains after drying. The hyperspectral NIR imaging technique combined with principal-component analysis made it possible to discriminate the dried vegetables according to their drying degree.