• Computers and Concrete
• /
• 제10권1호
• /
• pp.59-78
• /
• 2012

Although the effect of corrosion of reinforcing bar on the shear behavior of the reinforced concrete (RC) beam had been simulated by tests of the beam with unbonded, half-exposed or whole-exposed tensile steel reinforcements as well as defective stirrup anchorages, theoretical methods to accurately predict remaining capacity of this kind of RC beams, especially shear capacity, are still lacking. Considering the possible position of the critical inclined crack, the actual pattern of strains in the concrete body within the partial length and the proposed compatibility condition of deformations of the RC beam, shear strength of the RC beam with unbonded or exposed tensile steel reinforcements and/or defective stirrup anchorages is predicted. Comparison between the model's predictions with the experimental results published in the literature shows the practicability of the proposed model. Influence of the length of unbonded or exposed tensile steel reinforcements and the percentage of stirrups lacked end anchorages on the shear strength of the RC beam is discussed. It is concluded that, the shear strength of the RC beam with unbonded or exposed tensile steel reinforcements and/or defective stirrup anchorages is greatly influenced by the length of unbonded or exposed tensile steel reinforcements and the percentage of stirrups lacked end anchorages, this influence can be adverse, insignificant or even favourable, dependent on the given parameters of the corresponding normal bonded RC beam.

• 한국지반공학회논문집
• /
• 제15권6호
• /
• pp.187-200
• /
• 1999

타이백 앵커 억지 토류벽의 거동을 분석하기위해 광범위한 현장계측자료를 조사하고 이중 한 현장에 대한 유한요소해석을 실시하였다. 특히, 임의 굴착깊이에 대한 벽체변위-앵커자유장-앵커긴장하중 사이의 상관성을 조사하였다. 유한요소해석은 앵커하중과 앵커자유장을 변화시키면서 벽체변위의 증감을 조사하기 위해 실시하였다. 굴착깊이로 정규화시킨 횡방향 벽체 변위와 앵커위치의 상관도를 작성하였으며 임의 굴착깊이에 대한 벽체변위-앵커자유장-앵커긴장하중 사이에 고유한 관계가 설정됨을 확인하였다. 차후 실무차원에서 이를 활용하기 위해서는 더 많은 현장계측자료의 집적과 유한요소해석의 추가적인 실시가 필요하다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2003년도 봄 학술발표회 논문집
• /
• pp.545-552
• /
• 2003

For temporary excavation support in a congested urban area, the strand of ground anchor should be removed to get permission of the private land to install anchors. But the strand doesn't need to be removed in the outside city area after use. So the anchor body, tension anchor, is fabricated in-situ. The unbonded length of This anchor has several strands, which wrap only one sheath. When the anchor body is carried into job-site or installed in the bore hole, the sheath is torn easily because it is a very week material. So the grout permeate into the torn sheath. Because of that, the load doesn't transfer to the bond length of ground anchors. It may indicate that load is being transferred along the unbonded length and thus within the potential slip surface assumed for overall stability of the anchored system. The load tests were performed on seven low-pressure grouted anchors installed in weathered soil to verify its problems. Four anchors(Type A) have the unbonded length, which consist of five strands and a week sheath and three anchors(Type B) have strands, which is covered by plastic sheath filled with grease, in the unbonded length. Both anchors are compared with load tests results.

• Computers and Concrete
• /
• 제6권3호
• /
• pp.235-252
• /
• 2009

Due to the reduction of bond strength resulting from the high corrosion level of reinforcing bars, influence of this reduction on flexural capacity of reinforced concrete (RC) beam should be considered. An extreme case is considered, where bond strength is complete lost and/or the tensile steel are exposed due to heavy corrosion over a fraction of the beam length. A compatibility condition of deformations of the RC beam with partially unbonded length is proposed. Flexural capacity of this kind of RC beam is predicted by combining the proposed compatibility condition of deformations with equilibrium condition of forces. Comparison between the model's predictions with the experimental results published in the literature shows the practicability of the proposed model. Finally, influence of some parameters on the flexural capacity of RC beam with partially unbonded length is discussed. It is concluded that the flexural capacity of the beam may not be influenced by the completely loss of bond of the whole beam span as long as the tensile steel can yield; whether or not the reduction of the flexural capacity of the beam resulting from the loss of bond over certain length may occur depends on the detailed parameters of the given beam.

• KCI Concrete Journal
• /
• 제12권1호
• /
• pp.131-138
• /
• 2000

The research purpose of this paper is to investigate the influential Parameters on the unbonded tendon stress. The parameters were the reinforcing ratio, the prestressing ratio, and the loading type. To this end. first, the influence of parameters were examined with twenty eight test results obtained from references. Then, an experimental study was carried out with nine specimens. Test variables were the reinforcing ratio and the prestressing ratio. Specimens were divided equally into three groups and each group had a different level of the reinforcing ratio. Each specimen within a group has a different level of the prestressing ratio. The investigation with previous and current tests revealed the followings; (1) the length of crack distribution zone does not have a close relation with the length of plastic hinge. (2) the prestressing ratio does not affect both the length of crack distribution and the length of plastic hinge, (3) the tendon stress variation is in reverse relation with the ratios of mild steels and tendons, (4) the loading type nay not affect significantly the length of crack distribution zone, (5) AASHTO LRFD Code equation and Moon/Lim's design equation predicted the test results well with some safety margins.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1998년도 가을 학술발표회 논문집
• /
• pp.249-256
• /
• 1998

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 춘계학술발표회 논문집(I)
• /
• pp.258-261
• /
• 2006

This study investigates the flexural behavior and strengthening performance of RC beams with unbonded prestressing CFRP laminates through static bending tests. The aluminum anchorage system has been developed in tins study and successfully applied to the test specimens. The prestressing level of CFRP laminatehas was 0 %, 20 %, 30% and 50 % of its tensile strength. Experimental results revealed that RC beams with unbonded prestressing CFRP laminates showed increased crack load and yield load according to the level of prestress. It has also been observed that the length of the CFRP laminates does not have significant effect on the maximum load.

• 콘크리트학회논문집
• /
• 제15권1호
• /
• pp.143-153
• /
• 2003

철근콘크리트를 FRP 복합재로 보강할 경우, 취성파괴를 방지하고 연성파괴를 확보할 수 있는 새로운 기법을 표면매립공법(Near Surface Mounted technique: 이하 NSM 공법)에 근거하여 제시하였다. 제안된 기법은 Hybrid FRP rebar를 부분적으로 비부착 시킴으로서 보강된 보의 연성을 확보한다. Hybrid FRP rebar의 일부를 비부착으로 한 경우와 전부를 부착으로 한 경우의 NSM 공법에 의한 FRP 보강된 철근 콘크리트보의 거동을 비교하기 위한 실험을 실시하였다. 실험 결과, 부분 비부착 NSM 공법으로 보강된 철근 콘크리트보만이 연성거동을 함이 관찰되었다. 부분 비부착 보강된 보의 극한 시 내력을 확보하기 위한 최소한의 FRP의 부분 비부착길이를 이론적으로 산정하여 제시하였다. 제시된 부분 비부착 NSM 공법은 FRP 복합재로 보강된 철근 콘크리트 부재의 구조적 거동을 크게 향상시킬 수 있으리라 기대된다.

• 대한토목학회논문집
• /
• 제28권4A호
• /
• pp.439-445
• /
• 2008

본 논문에서는 비부착 CFRP판으로 긴장 보강된 철근콘크리트 보를 해석하기 위한 수정된 부착감소계수를 제안하였다. 기존의 비부착 강연선의 극한응력 해석식에 대한 분석을 통해 비부착 CFRP판 긴장재로 보강된 철근콘크리트 보에 대한 적용성을 검토하였으며, 적용상의 문제점을 도출하였다. 합리적인 비부착 CFRP판 극한응력 해석식을 제안하기 위해 부착 CFRP판 긴장재의 평균변형률 개념으로부터 비부착 CFRP판 긴장재의 보강길이와 하중 재하 형태에 따른 순수휨구간 길이가 고려된 확장된 부착감소계수를 제안하였다. 최종 부착감소계수는 기존의 비부착 CFRP판 긴장 보강보에 대한 실험연구 문헌의 실험결과를 이용한 통계적 방법으로 결정되었으며, 제안된 부착감소계수를 포함한 극한응력 해석식에 의해 계산된 값을 실험결과와 비교하여 제안식의 유효성을 검토하였다.

• 한국철도학회논문집
• /
• 제19권4호
• /
• pp.515-525
• /
• 2016

도시형 자기부상열차 프리텐션 거더교의 최적설계를 위해서 설계변수 분석을 수행하였다. 자기부상철도용 거더 설계 시에는 중앙부 처짐을 고려해야 하므로 이와 연관있는 콘크리트 압축강도, 거더 형고, 거더 연장및 강연선비부착 길이를 설계변수로 선정하였다. 또한, 프리텐션 거더에서 지점부의 상연응력을 제어하기 위해서 강연선 개소수 및 배치방식을 설계변수로 선정하고, 강연선비부착률을 검토하였다. 설계변수 해석결과로부터 거더 처짐량에는 거더 형고와 거더 연장이 콘크리트 압축강도와 강연선 비부착 길이보다 더 큰 영향을 미치는 것을 확인하였고, 민감도 분석을 통해 설계 가중값을 제시하였다. 지점부 상연응력 제어를 위해서 비부착 강연선배치기준을 만족하는 경우에는 상연 긴장선 또는 철근배근이 필요한 것으로 확인되었다. 따라서 향후 경제성 및 시공성 향상을 위해 자기부상철도 가이드웨이의 하중특성을 고려한 비부착강연선 기준 향상에 대한 검토가 필요하다.