• 비파괴검사학회지
• /
• 제9권2호
• /
• pp.18-24
• /
• 1989

Computer-aided high frequency ultrasonic is applied to aluminum oxide(85w%, 94w%, 96w%, and 99w%) MOR(modulus of rupture) samples to evaluate mechanical properties such as density variation, pore content, elastic modulus, shear modulus, and poisson's ratio. Ultrasonic wave velocity and attenuation measurement techniques were used as an evaluator of such properties. Pulse-echo C-Scan images with different fate setting method using 50MHz center frequency 1 inch focal length transducer allows evaluation of density variation and pore content. Elastic modulus calculated with the relation of density and ultrasonic velocity. It shows good reliability as compared with resonance method. Sintered density variation of $0.025g/cm^{3}$, that is 0.6% of theoretical density in $Al_{2}O_{3}$ samples can be observed by ultrasonic velocity measurement. Attenuation measurement method qualitatively agree with 4-point fracture testing result concerning of porosity content.

• Smart Structures and Systems
• /
• 제17권1호
• /
• pp.73-89
• /
• 2016

The stress dependence of ultrasonic wave velocity is known as the acoustoelastic effect. This effect is useful for stress monitoring if the acoustoelastic coefficient of a subject medium is known. The acoustoelastic coefficients of metallic materials such as steel have been studied widely. However, the acoustoelastic coefficient of concrete has not been well understood yet. Basic constituents of concrete are water, cement, and aggregates. The mix proportion of those constituents greatly affects many mechanical and physical properties of concrete and so does the acoustoelastic coefficient of concrete. In this study, influence of the water-cement ratio (w/c ratio) and the fine-coarse aggregates ratio (fa/ta ratio) on the acoustoelastic coefficient of concrete was investigated. The w/c and the fa/ta ratios are important parameters in mix design and affect wave behaviors in concrete. Load-controlled uni-axial compression tests were performed on concrete specimens. Ultrasonic wave measurements were also performed during the compression tests. The stretching coda wave interferometry method was used to obtain the relative velocity change of ultrasonic waves with respect to the stress level of the specimens. From the experimental results, it was found that the w/c ratio greatly affects the acoustoelastic coefficient while the fa/ta ratio does not. The acoustoelastic coefficient increased from $0.003073MPa^{-1}$ to $0.005553MPa^{-1}$ when the w/c ratio was increased from 0.4 to 0.5. On the other hand, the acoustoelastic coefficient changed in small from $0.003606MPa^{-1}$ to $0.003801MPa^{-1}$ when the fa/ta ratio was increased from 0.3 to 0.5. Finally, it was also found that the relative velocity change has a linear relationship with the stress level of concrete.

• 오토저널
• /
• 제9권4호
• /
• pp.41-49
• /
• 1987

It is an experimental study to improve the characteristics of combustion and exhaust emission gas in the gasoline engine. These characteristics are influenced by the fuel droplet size. To improve these characteristics, we make the ultrasonic atomization apparatus, and compare with the commercial carburetor. The results obtained are as follows: 1. Maximum atomization quantity is obtained by the vibrator of resonancy frequency 1.65MHz in the ultrasonic atomization apparatus. 2. With ultrasonic atomization apparatus, more than 99% of atomization rate can be obtained regardless of intake air temperature, velocity, and air-fuel ratio. 3. Atomization rate of the commercial carburetor increases with the air-fuel ratio and intake air temperature. 4. Difference of atomization rate between the ultrasonic atomization apparatus and the commercial carburetor increases with decreasing air-fuel ratio. 5. Droplet size is about 1-5.mu.m at the ultrasonic atomization apparatus, and 80-150.mu.m at the commercial carburetor, which indicates the ultrasonic atomization apparatus is excellent in atomization.

• 비파괴검사학회지
• /
• 제23권4호
• /
• pp.334-341
• /
• 2003

중수로 압력관이 주위를 둘러싸고 있는 칼란드리아관과 접촉될 경우, 압력관의 내면과 외면의 온도차로 인하여 수소(중수소)의 열 확산이 발생하며 결과적으로 압력관 외면에 수소화물 블리스터가 형성된다. 수소화물 블리스터는 음향학적으로 지르코늄 매질과 연속성을 가지기 때문에 일반적인 초음파 검사법으로는 탐지하기가 어렵다. 지르코늄 압력관 외면에 발생한 작은 수소화물 블리스터를 압력관 내면에서 탐지하기 위하여 초음파 모드 변환 및 속도비 방법을 개발하였다. 정적인 열확산 실험 장치를 사용하여 압력관 외면에 수소화물 블리스터를 성장시켰다. 종파 에코의 비행시간과 모드 변환된 반사 횡파 에코의 비행시간을 측정하여 종파 대 횡파 속도비를 계산하였으며 이를 속도비를 수정된 등고선 표현 방식으로 나타냈다. 초음파 속도비 방법이 일반적인 종파 비행시간방법보다 수소화물 블리스터 탐지 감도가 우수하며 블리스터 형상화 측면에서도 실제 형상과 유사하게 재현하고 있음을 알 수 있었다. 또한 중수로 압력관 초음파 검사사양과 동일하게 최적화 조건에서 수소화물 블리스터 탐지한계는 보수적인 관점에서 압력관 외면에 나타나는 크기를 기준으로 약 $500{\mu}m$로 평가되었다.

• Geomechanics and Engineering
• /
• 제14권4호
• /
• pp.399-406
• /
• 2018

The influences of mineral content and porosity on ultrasonic wave velocity were assessed for ten hornfelsic rocks collected from southern and western parts of the city of Hamedan, western Iran. Selected rock samples were subjected to mineralogical, physical, and index laboratory tests. The tested rocks contain quartz, feldspar, biotite, muscovite, garnet, sillimanite, kyanite, staurolite, graphite and other fine grained cryptocrystalline matrix materials. The values of dry unit weight of the rocks were high, but the values of porosity and water absorption were low. In the rocks, the values of dry unit weight are related to the presence of dense minerals such as garnet so not affected by porosity. The statistical relationships between mineral content, porosity and ultrasonic wave velocity indicated that the porosity is the most important factor influencing ultrasonic wave velocity of the studied rocks. The values of P-wave velocity of the rocks range from moderate to very high. Empirical equations, relevant to different parameters of the rocks, were proposed to determine the rocks' essential characteristics such as primary and secondary wave velocities. Quality indexes (IQ) of the studied samples were determined based on P-wave velocities of them and their composing minerals and the samples were classified as non-fissured to moderately fissured rocks. Also, all tested samples are classified as slightly fissured rocks according to the ratio of S-wave to P-wave velocities.

• 비파괴검사학회지
• /
• 제28권6호
• /
• pp.519-523
• /
• 2008

Poisson's ratio is one of elastic constants of elastic solids. However, it has not attracted attention due to its narrow range and difficult measurement. Transverse wave velocity as well as longitudinal wave velocity should be measured for nondestructive measurement of Poisson's ratio. Hard couplant for transverse wave prevents transducer from scanning over specimen. In the present work, a novel measurement of Poisson's ratio distribution was proposed. Immersion method was employed for the scanning over the specimen. Echo signals of normal beam longitudinal wave were collected. Transverse wave modes generated by mode conversion were identified. From transit time of longitudinal and transverse waves, Poisson's ratio can be determined without information of specimen thickness. This technique was demonstrated for aluminum and steel specimens.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.1069-1074
• /
• 2004

This study investigated the effect of pressure variations on augmentation of heat transfer when the ultrasonic waves were applied. The augmentation ratio of heat transfer was experimentally investigated and was compared with the profiles of pressure distributions calculated applying a coupled finite element-boundary element method (coupled FE-BEM). As the ultrasonic intensities increase from 70W to 340W, the velocity of the liquid paraffin is found to increase as well as kinetic energy, This physical behavior known as quasi-Eckart streaming results from acoustic pressure variations in the liquid. Especially, the higher acoustic pressure distribution near two ultrasonic transducers develops more intensive flow (quasi-Eckart streaming), destroying the flow instability. Also, the profile of acoustic pressure variation is consistent with that of augmentation of heat transfer. This mechanism is believed to increase the ratio of hear transfer coefficient.

• 한국추진공학회지
• /
• 제16권3호
• /
• pp.16-23
• /
• 2012

정상초음파의 교반이 메탄/공기 예혼합화염의 동역학적 거동에 미치는 영향을 규명하는 실험 결과를 본 연구에서 제시한다. 슐리렌 기법을 이용하여 전파하는 화염을 가시화하였고, 이미지 후처리를 통해 정상초음파 유무에 따른 화염선단의 전파속도를 상세히 관찰하였다. 전파속도는 이론당량비에서 정상 초음파가 교반하는 경우에 크게 증가하였으며, 당량비가 연소 상한계 혹은 연소 하한계로 벗어남에 따라 교반의 효과는 감소하였다. 정상초음파장은 화염 구조의 왜곡을 동반하고, 그 변이 형상은 교반하는 초음파장의 특성에 전적으로 종속하였다.

• Nuclear Engineering and Technology
• /
• 제56권2호
• /
• pp.472-476
• /
• 2024

It is important that radioactive and nuclear wastes are immobilized in a glass composition with lower melting temperatures due to their economy. In this study, the elastic and mechanical properties of sodium borate-based vitrified radioactive waste were measured using ultrasonic techniques. Many ultrasonic parameters, such as elastic moduli, Poisson's ratio, and microhardness, were calculated by measuring the ultrasonic velocities of the glasses. The ultrasonic velocity data, the density, the calculated elastic moduli, micro-hardness, softening temperature, and Debye temperature depending on the glass composition were evaluated, and the relation with the structure was clarified. It was observed that the elastic modulus and Poisson ratio increased as the Cs₂O content increased in glasses containing Cs waste. This result shows that the rigidity of the network structure of these glasses increases in contrast to the glass containing Sr.

• 대한기계학회논문집A
• /
• 제34권6호
• /
• pp.751-756
• /
• 2010

비선형 초음파는 선형 초음파와 비교하였을 때 재료의 물성 변화에 민감하게 반응한다. 이 연구의 목표는 비선형 요소를 포함하여 열처리 조건과 초음파 비선형성의 상관관계를 알아내는 것이다. 본 연구에서 기존의 방법과는 다른 수정된 초음파속도계산 식이 새롭게 제안되었다. 이것은 열처리된 재질에서 초음파 속도변화가 재료의 비선형성 때문에 발생하는 것을 찾아내었다. 실험을 통하여 수정된 초음파 속도와 1차 조화 및 2차 조화파의 진폭 비율이 서로 동일한 경향을 보이는 것을 알아냈다. 그리고 수정된 초음파속도식을 통해 계산된 상대적인 비선형계수는 기존의 방법을 이용하였을 때보다 더 민감함을 알아냈다.