• 한국세라믹학회지
• /
• 제32권5호
• /
• pp.575-581
• /
• 1995

Zr0.94Y0.06O1.97 powder was synthesized by the ultrasonic spray pyrolysis with various concentrations of starting solution and the influence of powder characteristics on sintering behavior was investigated. Powders prepared at 75$0^{\circ}C$ were characterized as narrowly distributed submicron spherical particles, which were crystalline, nonagglomerated, and compositionally homogeneous. The changes in concentration from 0.01 to 01. mol/ι increased mean particle size from 0.24 to 0.38${\mu}{\textrm}{m}$ and decreased the specific surface area from 14.2 to 2.9$m^2$/g. The relative density of the specimen from the powders, prepared with the solution concentration of 0.01 mol/ι, was 98% after sintering for 2 hr at 1,45$0^{\circ}C$ and the monoclinic phase was observed after sintering at 1,55$0^{\circ}C$. As the concentration of starting solution was increased, the formation temperature of monoclinic phase was lowered.

• 센서학회지
• /
• 제13권1호
• /
• pp.66-71
• /
• 2004

Pt-doped zinc oxide (ZnO:Pt) films were deposited by ultrasonic spray pyrolysis. Resistivity variation with Pt concentration was measured. The Pt distribution in ZnO:Pt films was studied through Auger Electron Spectroscopy (AES). The ZnO:Pt films were annealed in the ambient of air, water vapor and ozone, respectively. The variation in crystallographic properties and surface morphologies with respect to the annealing condition was observed by X-Ray Diffraction (XRD) and Scanning Electron Microscopy (SEM). The resistivity variation of the films with the annealing condition was measured. Finally, Atomic Force Microscopy (AFM) measurements were carried out to study the effects of the annealing on the roughness of ZnO:Pt films.

• 한국생산제조학회지
• /
• 제24권4호
• /
• pp.469-474
• /
• 2015

In ultrasonic spray pyrolysis deposition, a precursor solution is evaporated by an ultrasonic atomizer, then gas-carried into a furnace where the solute is separated from the water vapor. After condensation, polymerization, and nucleation, the solute oxide forms a thin film. To improve the deposition efficiency, the ultrasonic atomizer was studied to optimize the evaporated gas flow. The vat cover was redesigned, using three versions with different inlet factors being tested through a computational fluid dynamic analysis as well as a water evaporation experiment. The atomization rate with a hemispherical cover with a $30^{\circ}$ inlet was found to be 2.4 times higher than that with the original. This improvement was verified with fluorine-doped tin oxide spray pyrolysis deposition. The film obtained with the modified vat cover was 2.4 times thicker than that obtained with the original vat cover.

• Journal of Biosystems Engineering
• /
• 제36권1호
• /
• pp.15-22
• /
• 2011

An experimental variable rate nursery sprayer was developed to adjust application rates for canopy volume in real time. The sprayer consisted of two vertical booms integrated with ultrasonic sensors, and variable rate nozzles coupled with pulse width modulation (PMW) based solenoid valves. A custom-designed microcontroller instructed the sensors to detect canopy size and occurrence and then controlled nozzles to achieve variable application rates. A spray delivery system, which consisted of diaphragm pump, pressure regulator and 4-cycle gasoline engine, offered the spray discharge function. Spray delay time, time adjustment in spray trigger for the leading distance of the sensor, was measured with a high-speed camera, and it was from 50 to 140 ms earlier than the desired time (398 ms) at 3.2 km/h under indoor conditions. Consequently, the sprayer triggered 4.5 to 12.5 cm prior to detected targets. Duty cycles of the sprayer were from 20 to 34 ms for senor-to-canopy (STC) distance from 0.30 to 0.76 m. Outdoor test confirmed that the nozzles were triggered from 290 to 380 ms after detecting tree canopy at 3.2 km/h. The spray rate of the new sprayer was 58.4 to 85.2% of the constant application rate (935 L/ha). Spray coverage was collected at four areas of evergreen canopy by water sensitive papers (WSP), and ranged from 1.9 to 41.1% and 1.8 to 34.7% for variable and constant rate applications, respectively. One WSP area had significant (P < 0.05) difference in mean spray coverage between two application conditions.

• 한국응용과학기술학회지
• /
• 제22권3호
• /
• pp.281-288
• /
• 2005

The silica nanoparticles were used as support of catalyst, filling material, electronic assembler, thin film material, and sensor material. And, the titania nanoparticles were used as pigment, dielectric substance, sensor and photocatalyst. In this paper, the spherical composite particles of $TiO_2/SiO_2$with narrow size distribution and phase pure were synthesized by ultrasonic spray pyrolysis method from $TiOSO_4$ and colloidal silica solution. Using ultrasonic apparatus, this starting solution was vaporized to droplets, and these droplets were induced into tube furnace by carrier gas. The resulting composite powder was characterized by scanning electron microscopy, X-ray diffraction analysis, TG-DTA, in vitro sun protection factor(SPF) and BET surface area analysis.

• 한국분말재료학회지
• /
• 제29권6호
• /
• pp.485-491
• /
• 2022

Lithium lanthanum titanium oxide (LLTO) is a promising ceramic electrolyte because of its high ionic conductivity at room temperature, low electrical conductivity, and outstanding physical properties. Several routes for the synthesis of bulk LLTO are known, in particular, solid-state synthesis and sol-gel method. However, the extremely low ionic conductivity of LLTO at grain boundaries is one of the major problems for practical applications. To diminish the grain boundary effect, the structure of LLTO is tuned to nanoscale morphology with structures of different dimensionalities (0D spheres, and 1D tubes and wires); this strategy has great potential to enhance the ion conduction by intensifying Li diffusion and minimizing the grain boundary resistance. Therefore, in this work, 0D spherical LLTO is synthesized using ultrasonic spray pyrolysis (USP). The USP method primarily yields spherical particles from the droplets generated by ultrasonic waves passed through several heating zones. LLTO is synthesized using USP, and the effects of each precursor and their mechanisms as well as synthesis parameters are analyzed and discussed to optimize the synthesis. The phase structure of the obtained materials is analyzed using X-ray diffraction, and their morphology and particle size are analyzed using field-emission scanning electron microscopy.

• 한국염색가공학회지
• /
• 제12권3호
• /
• pp.207-217
• /
• 2000

A new, high-efficiency ultrasonic fabric washing machine was developed to be an energy-efficient washing machine and to enhance fabric washing quality in washing processes of the dyeing and finishing process in the textile industry. This system is composed of ultrasonic wave generator, air blowing nozzle, torque motor for fabric tension control, and enclosed washing bath, multi-tube type exchanger, noiseless heater, air cylinder, expander roller, mangle upper and lower rollers, bend bar, dancer, shower spray nozzle, and solenoid valve, and so on. These elements are synergised for fabric washing. One of the very important principles is the low tension fabric running system. For an efficient washing effect, a counter flow system is also adopted. The new system also adopts the dancer and torque motor to control fabric tension and prevent fabric creasing. Shower spray nozzle, counter flow and overflow apparatus, and air-blowing apparatus are adopted to enhance the fabric washing effect. In this study, peach yoryu, exter, and moss crepe fabrics were washed by the general and ultrasonic washing systems under different conditions respectively. The washing efficiency was affected by the fabric running speed and characteristics of fabrics. Size content after washing increased with increasing the fabric running speed. The values in the general washing system were higher than those of the ultrasonic washing system. The changes of conductivity in the ultrasonic and the cooling bath were affected by the running time under the ultrasonic generating. The values of conductivity decreased as the experimental time passed.

• 한국세라믹학회지
• /
• 제28권10호
• /
• pp.831-837
• /
• 1991

Spherical TiO2 particles are prepared from TiCl4 aqueous solution by the spray pyrolysis method using ultrasonic atomization technique. The formation mechanism of TiO2 particles from atomized droplets it studied by varying the concentration of the source solution, reaction temperature, and the solvent. spherical TiO2 powders with almost the same normalized particle size distribution can be made reproducibly by changing the concentration of the source solution, and their mean sizes are in the range of 0.2~1.4${\mu}{\textrm}{m}$.

• 한국세라믹학회지
• /
• 제31권5호
• /
• pp.465-470
• /
• 1994

Fine, spherical (Zr, SN)TiO4 powders were prepared from the aqueous solution of metal chlorides by ultrasonic spray pyrolysis. Single phase (Zr, SN)TiO4 powders could be obtained above $700^{\circ}C$ (=temperature of the reactor) and all powders exhibited sizes in the range of 0.1 to 2.0 ${\mu}{\textrm}{m}$ and a narrow size distribution. The sintering properties of the prepared powders were better than those of the powders from solid-state reaction.

• 한국초전도학회:학술대회논문집
• /
• 한국초전도학회 2009년도 Korea Superconductivity Society Meeting 2009
• /
• pp.100-100
• /
• 2009