• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• v.2
• /
• pp.311-315
• /
• 2006

Precision location and positioning of Asset within a network is an attractive feature with various applications, especially in indoor environments. Such a demand is met by the standard task group, IEEE 802.15.4a. Several methods, that is, pulse, chirp and chaotic communications have been proposed so far to satisfy the requirements of the standard. Among them, ultra wideband direct chaotic communications has advantageous features such as low hardware complexity, low cost, lower power consumption and flexible frequency band plan. In this paper, the feasibility of the ranging system using non-coherent chaotic transceiver is investigated by designing and implementing the system and the performance is proved by conducting location experiments in real indoor environments.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.11 no.7
• /
• pp.665-670
• /
• 2016

In this paper, we suggest the design of OP-AMP using MOSFET in the operation of sub-threshold condition as a basic unit of an IoT. The sub-threshold operation of MOSFET is useful for an ultra low power consumption of sensor network system in the IoT, because it cause the supply voltage to be reduced. From the simulation result using 0.35 um CMOS process, the supply voltage, VDD can be reduced with 0.6 V, open-loop gain of 43 dB and the power consumption was evaluated with about $1.3{\mu}W$ and the active size for an integration was measured with $64{\mu}m{\times}105{\mu}m$. It is expected that the proposed circuit is applied to the low power sensor network for IoT.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.12
• /
• pp.67-73
• /
• 2015

This paper presents a fully integrated 3 - 5 GHz IR-UWB(impulse radio ultra-wide band) RFIC for Location based system. The receiver architecture adopts the energy detection method and for high speed sampling, the equivalent time sampling technique using the integrated DLL(delay locked loop) and 4 bit ADC. The digitally synthesized UWB impulse generator with low power consumption is also designed. The designed IR-UWB RFIC is implemented on $0.18{\mu}m$ CMOS technology. The receiver's sensitivity is -85.7 dBm and the current consumption of receiver and transmitter is 32 mA and 25.5 mA respectively at 1.8 V supply.

• Journal of Satellite, Information and Communications
• /
• v.12 no.1
• /
• pp.64-71
• /
• 2017

In this paper, Kalman filter and RRWA algorithm are used to estimate the accurate target in IR-UWB (Impulse-Radio Ultra Wideband) radar system, which enables accurate location recognition of indoors and outdoors with low cost and low power consumption. In the signal reflected by the target, unnecessary signals exist in addition to the target signal. We have tried to remove unnecessary signals and to derive accurate target signals and improve performance. The location of the targets is estimated in real time with one transmitting antenna and one receiving antenna. The Kalman filter was used to remove the background noise and the RRWA algorithm was used to remove the reflected signal. In this paper, we think that it will be useful to study the accurate distance estimation and tracking in future target estimation.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.1
• /
• pp.69-76
• /
• 2015

In this paper, we propose and analyze a M-ary transmission scheme in time hopping ultra-wide band(UWB) system using mutually orthogonal modified Hermite polynomial(MHP) pulses. The proposed M-ary transmission scheme employs the orthogonal property between different ordered pulses and N data bits make the M-ary signals by linear combination of M MHP pluses. The theoretical analysis and simulation results show that the proposed system has better performance and higher data rate than conventional M-ary UWB system. We derive the general form of correlation function for MHP pulses and analyze bit error rate(BER) performance over additive white Gaussian noise(AWGN) with the presence of timing jitter. We show that the proposed system has the improved BER performance and robustness to timing jitter and low power spectrum density compared with conventional M-ary UWB system.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.1
• /
• pp.98-106
• /
• 2009

This work proposes a 1280-RGB $\times$ 800-Dot 70.78mW 0.l3um CMOS LCD driver IC (LDI) for high-performance 16M-color low temperature poly silicon (LTPS) thin film transistor liquid crystal display (TFT-LCD) systems such as ultra mobile PC (UMPC) and mobile applications simultaneously requiring high resolution, low power, and small size at high speed. The proposed LDI optimizes power consumption and chip area at high resolution based on a resistor-string based architecture. The single column driver employing a 1:12 MUX architecture drives 12 channels simultaneously to minimize chip area. The implemented class-AB amplifier achieves a rail-to-rail operation with high gain and low power while minimizing the effect of offset and output deviations for high definition. The supply- and temperature-insensitive current reference is implemented on chip with a small number of MOS transistors. A slew enhancement technique applicable to next-generation source drivers, not implemented on this prototype chip, is proposed to reduce power consumption further. The prototype LDI implemented in a 0.13um CMOS technology demonstrates a measured settling time of source driver amplifiers within 1.016us and 1.072us during high-to-low and low-to-high transitions, respectively. The output voltage of source drivers shows a maximum deviation of 11mV. The LDI with an active die area of $12,203um{\times}1500um$ consumes 70.78mW at 1.5V/5.5V.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.53-53
• /
• 2008

Piezoelectric transformers have been widely used such as DC-DC convertor, invertor, Ballast, etc. Because, the y have some merits compared with electro-magnetic transformers such as step-up ratio, high efficiency, small size and lg hit weight, etc. Piezoelectric transformer require high electromechanical coupling factor kp in order to induce a large out put power in proportional to applied electric field. And also, high mechanical quality factor Qm is required to prevent mechanical loss and heat generation. In general, PZT system ceramics should be sintered at high temperatures between 1200 and $1300^{\circ}C$ in order to obtain complete densification. Accordingly, environmental pollution due to its PbO evaporation. Hence, to reduce its sintering temperature, various kinds of material processing methods such as hot pressing, high energy mill, liquid phase sintering, and using ultra fine powder have been performed. Among these methods, liquid phase sintering is basically an effective method for aiding densification at low temperature. In this study, In order to comparis on low temperature sintering and solid state sintering piezoelectric transformers, rosen type transformers were fabricated u sing two PZT ceramics compositions and their electrical properties were investigated.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.7C
• /
• pp.443-450
• /
• 2011

Recently, various transmission techniques for communication and broadcasting systems have been developed to meet the dramatically increasing requirement of consumers. Because UWB (Ultra-Wideband) is a wireless communication technique that supports high data rate with low power, it can satisfy the requirement and can be applied to various wireless communication services. The multi-band orthogonal frequency division multiplexing (MB-OFDM) system, one of UWB system, is the wireless communication system that satisfies the transmission characteristic for UWB and so it can be used for various wireless communication services. In this paper, we propose a scheme that uses hierarchical modulation which is applied in digital video broadcasting system at the source and adaptive modulation based on the channel quality at the relays. The simulation results have shown that the proposed scheme has both the advantages of the increased throughput by 33% and similar BER performance to conventional scheme.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.48 no.12
• /
• pp.777-784
• /
• 1999

Since the ultra-high voltage power apparatus are recommended to withstand switching surge generated from the electric power system, the switching impulse voltage is generally used to verify this requirement at the testing laboratories. Recently, the international standard(IEC 60060-2) related to the high voltage measurement techniques is revised requiring a traceability of measuring system for high voltage measurements. In this paper, a reference divider for switching impulse voltage is developed satisfying the revised. IEC standard and the possibility of applications has been investigated. Therefore, the characteristics of the high and low voltage side resistor and the shielding ring have been analyzed including the step response characteristics of the prototype divider. Throughout various efforts, it is confirmed that our measuring device has shown compatible characteristics as a reference divider.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.5 no.5
• /
• pp.869-876
• /
• 2001

In modern wireless communication, it has been regarded as a important problem for the spectrum efficiency to utilize the limited frequency-resource efficiently. In addition, the system architecture has been designed for low cost, low power consumption and ultra-lightweight. In this paper, we directly modulated the BCPFSK with a superior spectrum efficiency using the DDS and applied the direct conversion to the system architecture. Finally, we designed a transceiver which has the 433 MHz BCPFSK output and evaluated the system performance. In the measured result, we know that as for spectrum and the power efficiency, BCPFSK method is better than conventional one. Also, the results of the designed system is 433.92 MHz in center frequency and about 33 dBc in carrier suppression ratio. And we get the better results in local oscillator leakage and the spurious of the ISM out-band the same as -69dBc and under 60dBc.