• International Journal of Aeronautical and Space Sciences
• /
• 제14권2호
• /
• pp.146-151
• /
• 2013

Carbon nanofibers (CNFs) are electrically conductive. When CNFs are used as fillers in resin, this electrical conductivity can be yielded without adversely affecting the mechanical properties of the resin. When an elastomer is adopted as the resin, a conductive elastomer can then be produced. Due to its flexibility and conductive properties, a large strain sensor based on changes in resistivity may be produced, for strain sensing in flexible structures. In this study, a patch-type large strain sensor using resistivity change in a CNF/elastomer composite was proposed. The measurement limits of the sensor were investigated experimentally, and the limit was found to be 40%, which greatly exceeded the limits of conventional metal-foiled strain gages. Also, the proposed CNF/elastomer large strain sensor can be used to measure flexible materials, while conventional strain gages cannot be used to measure such strains.

• 대한설비공학회지:설비저널
• /
• 제17권2호
• /
• pp.150-158
• /
• 1988

On a refrigeration compressor, damage of a discharge valve is one of the annoying troubles for an engineer. Small size compressors, having ring plate type discharge valve are recently used. Therefore, it is very important for engineers to measure and analyze strains of discharge valve. The purpose of this study is to obtain the basic data of the strain of the flexible ring valve. Measurements were performed by the strain gauge bonded on the surface of the flexible ring valve. Stress and strain of the valve were calculated by the method of uniformly loaded circular plates with a central hole. The results obtained are as follows; (1) the strain of flexible ring discharge valve in refrigeration compressor was influenced by tension and compression strain simultaneously. (2) for a given discharge pressure, the tangential and radial strains was increased with increasing discharge pressure. (3) the valve of radial strain was larger than that of tangential strain.

• Nuclear Engineering and Technology
• /
• 제53권2호
• /
• pp.647-656
• /
• 2021

Knowing a material's true stress-strain curve is essential for performing a nonlinear finite element analysis to solve an elastoplastic problem. This study presents a simple methodology to determine the true stress-strain curve of type 304 and 316 austenitic stainless steels in the full range of strain from a typical tensile test. Before necking, the true stress and strain values are directly converted from engineering stress and strain data, respectively. After necking, a true stress-strain equation is determined by iteratively conducting finite element analysis using three pieces of information at the necking and the fracture points. The Hockett-Sherby equation is proposed as an optimal stress-strain model in a non-uniform deformation region. The application to the stainless steel under different temperatures and loading conditions verifies that the strain hardening behavior of the material is adequately described by the determined equation, and the estimated engineering stress-strain curves are in good agreement with those of experiments. The presented method is intrinsically simple to use and reduces iterations because it does not require much experimental effort and adopts the approach of determining the stress-strain equation instead of correcting the individual stress at each strain point.

• Journal of Microbiology
• /
• 제39권3호
• /
• pp.236-239
• /
• 2001

Group A Streptococcus strain ST4529 is a provisional new ems type which has been recently reported in Malaysia (Jomal, et al. 1999. Energ. Infect . Dis. 5,10-14). This strain was found to be opacity factor (OF) negative with a Tl phenotype. Usually, OF negative strains with T1 phenotypes are associated with acute rheumatic fever. However, strain ST4529 was isolated from the blood of a patient with septicemia. Comparison of the deduced amino acid sequence of the mature hypervariable N-terminus of ST4529 showed only 43% identity with that of M5, the closest matched OF negative strain with a T1 phenotype. Thus, ST4529 most probably encodes a new serospecifically unique M protein which is associated with septicemia rather than pharyngitis infections. The strains with these phenotypes are very important because their sequences should be considered for developing any anti-streptococcal vaccines.

• Journal of Welding and Joining
• /
• 제17권6호
• /
• pp.32-37
• /
• 1999

Since stainless steel plates have good mechanical properties, weldability, appearance and resistance of corrosion, these are traditionally used for vehicles such as the bus and the train. And they are mainly fabricated by spot welding. But fatigue strength of their spot welded joint is considerably influenced by welding conditions as well as geometrical factors. Thus a reasonable and systematic criterion for long life design of spot welded body structure must be established. In this report, strain energy density was analyzed by using 3-dimensional finite element model about the IB-type spot welded lap joint under tension-shear load. Fatigue tests were conducted on them having various thickness, joint angle, lapped length and width. From their results, it was found that fatigue strength of the IB-type spot welded lap joints could be effectively and systematically rearranged by strain energy density at the edge of nugget.

• Nuclear Engineering and Technology
• /
• 제45권3호
• /
• pp.361-366
• /
• 2013

An imaging technique to visualize the internal defects in a plate-type nuclear fuel specimen was developed by using an active optical interferometer for a nondestructive quality inspection. A periodic thermal wave having a sinusoidal intensity pattern induced a periodical strain variation for the specimen. The varying strain image was acquired using an optical laser interferometer. The strain distribution over the internal defects will be distorted in an acquired strain image because a part of the thermal wave will be reflected from these defects during propagation. In this paper, internal defects were efficiently visualized by sequentially accumulating the extracted defect components. The experimental results confirmed that the developed visualization system can be a valuable tool to detect the internal defects in plate-type nuclear fuel.

• Journal of Microbiology and Biotechnology
• /
• 제3권2호
• /
• pp.95-98
• /
• 1993

This study was carried out to isolate and characterize the mutant strains of Schwanniomyces castellii NRRL Y-2477. Mutants were prepared with the treatment of ethyl methane sulfonate. 2-deoxy-D-glucose resistant mutants were isolated and two mutants were selected based on their high production of amylolytic enzymes and their ability to ferment starch. The mutants selected had higher a-amylase and glucoamylase activities than the wild type strain from several other carbon sources. Especially, it was revealed that mutant strain M-9, when cultured in the presence of glucose as a sole carbon source, shows relatively high activities of a-amylase and glucoamylase compared to those of the wild type strain. In result, this mutant strain can be considered as a constitutive producer of amylolytic enzymes. To compare the ethanol production ability of wild type strain and of mutant strains selected, an alcohol fermentation was carried out using 100 g/l soluble starch. Mutant strain M-9 did not improve the direct alcohol fermentation of starch, despite its excellent amylolytic activities performance. On the other hand, mutant strain M-6 produced 37.9 g/l (4.8%, v/v) ethanol by utilizing about 82% of substrate.

• 한국해양공학회지
• /
• 제30권2호
• /
• pp.117-124
• /
• 2016

A C-type LNG mock-up tank was constructed to evaluate the durability of the tank and its structural safety. An experimental strain analysis system equipped with strain gages was designed to investigate the structural behavior of the inner tank at a high hydraulic pressure. In addition, the insulation used in the space between the inner tank and outer tank had a compressive strength and the inner tank thickness of the cylindrical shell and hemisphere was 4.0 mm, which was designed to be thinner than the existing rules. The strains on the inner tank were measured with increasing pressure, and these measurements were compared and analyzed at the strain gage attachment points.

• 소성∙가공
• /
• 제26권1호
• /
• pp.18-27
• /
• 2017

A comparative study was performed on strain-compensated Arrhenius-type constitutive models established with two regression methods: polynomial regression and regression Kriging. For measurements at high temperatures, experimental data of 70Cr3Mo steel were adopted from previous research. An Arrhenius-type constitutive model necessitates strain compensation for material constants to account for strain effect. To associate the material constants with strain, we first evaluated them at a set of discrete strains, then capitalized on surrogate modeling to represent the material constants as a function of strain. As a result, disparate flow stress models were formed via the two different regression methods. The constructed constitutive models were examined systematically against measured flow stresses by validation methods. The predicted material constants were found to be quite accurate compared to the actual material constants. However, notable mismatches between measured and predicted flow stresses were revealed by the proposed validation techniques, which carry out validation with not the entire, but a single tensile test case.

• 한국지반신소재학회논문집
• /
• 제3권2호
• /
• pp.31-38
• /
• 2004

2종류 지오그리드의 장기안정성의 검토되었다. 멤브레인 연신형 지오그리드는 지수함수형 인장거동을, 섬유형 지오그리드는 파단점에 가까울수록 빠른 인장특성 증가를 나타내었다. 섬유형 지오그리드의 경우 가속 크리프 시험을 실시하였지만 멤브레인 연신형 지오그리드의 경우에는 열적특성 때문에 가속 크리프 시험을 실시할 수 없었다. 멤브레인 연신형 지오그리드의 크리프 변형률은 인장시험에 의한 극한변형률보다 훨씬 큰 값을 나타내었으며, 섬유형 지오그리드의 크리프 변형에 의한 감소인자는 멤브레인 연신형 지오그리드에 비해 작은 값을 나타내었다.