• International Journal of Naval Architecture and Ocean Engineering
• /
• v.2 no.3
• /
• pp.132-138
• /
• 2010

In the present study, the real-time monitoring system is developed based on the wireless sensor network (WSN) and power line communication (PLC) employed in the 3,000-ton-class training ship. The WSN consists of sensor nodes, router, gateway and middleware. The PLC is composed of power lines, modems, Ethernet gateway and phase-coupler. The basic tests show that the ship has rather good environments for the wired and wireless communications. The developed real-time monitoring system is applied to recognize the thermal environments of main-engine room and one cabin in the ship. The main-engine room has lots of heat sources and needs careful monitoring to satisfy safe operation condition or detect any human errors beforehand. The monitoring is performed in two regions near the turbocharger and cascade tank, considered as heat sources. The cabin on the second deck is selected to monitor the thermal environments because it is close to the heat source of main engine. The monitoring results of the cabin show the thermal environment is varied by the human activity. The real-time monitoring for the thermal environment would be useful for the planning of the ventilation strategy based on the traces of the human activity against inconvenient thermal environments as well as the recognizing the temperature itself in each cabin.

• International Journal of Automotive Technology
• /
• v.8 no.6
• /
• pp.687-696
• /
• 2007

To increase the reliability of auto-ignition in CAI engines, the thermodynamic properties of intake flow is often controlled using recycled exhaust gases, called internal EGR. Because of the internal EGR influence on the overall thermodynamic properties and mixing quality of the gases that affect the subsequent combustion behavior, optimizing the intake and exhaust valve timing for the EGR is important to achieve the reliable auto-ignition and high thermal efficiency. In the present study, fully 3D numerical simulations were carried out to predict the mixing characteristics and flow field inside the cylinder as a function of valve timing. The 3D unsteady Eulerian-Lagrangian two-phase model was used to account for the interaction between the intake air and remaining internal EGR during the under-lap operation while varying three major parameters: the intake valve(IV) and exhaust valve(EV) timings and intake valve lift(IVL). Computational results showed that the largest EVC retardation, as in A6, yielded the optimal mixing of both EGR and fuel. The IV timing had little effect on the mixing quality. However, the IV timing variation caused backflow from the cylinder to the intake port. With respect to reduction of heat loss due to backflow, the case in B6 was considered to present the optimal operating condition. With the variation of the intake valve lift, the A1 case yielded the minimum amount of backflow. The best mixing was delivered when the lift height was at a minimum of 2 mm.

• Journal of Korean Physical Therapy Science
• /
• v.16 no.3
• /
• pp.55-66
• /
• 2009

Background: The purpose of this research was to investigate the factors affecting the low back pain of workers in hospital. 214 subjects waking at two general hospitals in Yosu city participated in this survey. Subjects consisted of doctors, nurses, medical engineers, officers and general laborers. The survey data were collected by a written questionnaire which made out by themselves for 25 days, from fourth August to 29th August, 2008. Methods: The questionnaire consisted of four categories, general, occupational, working habitual and the daily living characteristics. The collected data were analyzed by Chi-square test based on the present or absent of low back pain. Results: 1. In the general characteristics, low back pain had no significant relationship to all factors, sex, ago, body mass index, weight and height. 2. In the occupational characteristics, the phase of distribution of low back pain had statistical significant differences in the working hours a week, satisfaction of pay, satisfaction of occupation(p<0.05). However low back pain did not significantly related to the kind of occupation, period of work and degree of stress. 3. In the habitual characteristics, low back pain was significantly influenced by working posture, frequency of using lumbar and heavy material lifting, monotonous repetition of working operation and noise(p<0.05). No significant difference was shown in the factor of convenience of chair. 4. In the daily living characteristics, low back pain shown the significant differences in walking time a day, status of health and smoking pattern(p<0.05). there were, however, no significant differences in the aspect of the kind of house and bed, sleeping attitude, driving, riding time on the vehicle, exercising, frequency of cultural life and drinking alcohol. Conclusion: when I see above resultants totally, it appears a higher incidence caused by working environment rather than living habit and then consequently compared to hospital workers, they also have high incidence like others. In order to reduce incidence of low back pain and enjoy the our life we need to educate ourselves preventing program for low back pain and try to effort for preventing of low back pain on each department and individual.

• Journal of Aerospace System Engineering
• /
• v.10 no.4
• /
• pp.90-97
• /
• 2016

GEO-KOMPSAT-2A and GEO-KOMPSAT-2B are under development by KARI to replace the COMS mission, and will be launched in 2018 and 2019, respectively. GEO-KOMPSAT-2 will be launched and injected into the GTO (Geostationary Transfer Orbit) by the Ariane V launcher. Once injected into the GTO, the satellites are transferred to the drift orbit by applying a series of apogee engine burns. The burn epoch time, duration, and intervals are selected such that the satellite is placed closest to the target drift longitude, or at the drift start longitude. For GEO-KOMPSAT-2, four or five LAE (Liquid Apogee Engine) burns will be applied for drift orbit injection. This paper establishes the GEO-KOMPSAT-2 LAE burn plan, considering predefined constraints and adjustments, taking into account the perturbing forces. Two approaches have been analyzed: the first is a single shot approach, whereas the other is an iteration based optimal solution. Optimal solution has been obtained using the Focusleop, a geostationary satellite LEOP tool.

• Spatial Information Research
• /
• v.8 no.1
• /
• pp.155-170
• /
• 2000

When we use R-Tree,a spatial index, to find objects matches some predicate, it often leads to an incorrect result of perform filtering step only with MBR. And , each candidates need to be inspected to conform if it really satisfies with given query, so called, 'refinement step'. In refinement step. we should perform disk I/O and expansive spatial operations which is the cause of increasing retrieval costs. Therefore, to minimize the number of candidate after filtering step, two-phase filtering methods were studied, but there was many problems such as inefficiency of filtering,maintenance of additional informations and reconstruction of data resulted from the loss of original information. So , in this paper, I propose an Extended R-Tree which provides ability to retrieve spatial objects only with some simple logical operations using Grid Table, truth table strong the information about the existence of spatial objects, in second filtering step. Consequently , this Extended R-Tree using Grid Filter has low cost of operation for filtering because of efficient second filtering step, and better filtering efficiency caused by high quality of approximation.

• Investigative Magnetic Resonance Imaging
• /
• v.24 no.3
• /
• pp.95-122
• /
• 2020

In this article, we evaluated the performance of radiofrequency (RF) coils in terms of the signal-to-noise ratio (S/N) and homogeneity of magnetic resonance images when used for ultrahigh-frequency (UHF) 7T magnetic resonance imaging (MRI). High-quality MRI can be obtained when these two basic requirements are met. However, because of the dielectric effect, 7T magnetic resonance imaging still produces essentially a non-uniform magnetic flux (|B₁|) density distribution. In general, heterogeneous and homogeneous RF coils may be designed using electromagnetic (EM) modeling. Heterogeneous coils, which are surface coils, are used in consideration of scalability in the |B₁| region with a high S/N as multichannel loop coils rather than selecting a single loop. Loop coils are considered state of the art for their simplicity yet effective |B₁|-field distribution and intensity. In addition, combining multiple loop coils allows phase arrays (PA). PA coils have gained great interest for use in receiving signals because of parallel imaging (PI) techniques, such as sensitivity encoding (SENSE) and generalized autocalibrating partial parallel acquisition (GRAPPA), which drastically reduce the acquisition time. With the introduction of a parallel transmit coil (pTx) system, a form of transceiver loop arrays has also been proposed. In this article, we discussed the applications and proposed designs of loop coils. RF homogeneous coils for volume imaging include Alderman-Grant resonators, birdcage coils, saddle coils, traveling wave coils, transmission line arrays, composite right-/left-handed arrays, and fusion coils. In this article, we also discussed the basic operation, design, and applications of these coils.

• Korean Journal of Construction Engineering and Management
• /
• v.5 no.3 s.19
• /
• pp.71-78
• /
• 2004

In conventional method of supporting soil shuttering wall during excavation a system of struts and wales to provide cross-lot bracing is common in trench excavations and other excavations of limited width. This method, however, becomes difficult and costly to be adopted for large excavations since heavily braced structural systems are required. Another expensive and unsafe situations are expected when temporary struts must be removed for the construction of underground structures. This paper introduces innovative strut systems which can be used as permanent underground structures after its role as brace system to resist earth pressure during excavation phase. Underground structural system suggested from architect is checked against the soil lated pressures before the analysis of stresses developed from gravity loads. In this technology, named SPS(Struts as Permanent System), retaining wall is installed first and excavation proceeds until the first level of bracing is reached. Braces used as struts during excavation will serve as permanent girders when buildings are in operation. Simultaneous construction of underground and superstructure can proceeds when excavation ends with the last level of braces being installed. In this paper, construction sequence and the calculation concept are explained in detail with some photo illustrations. SPS technology was applied to three selected buildings. One of them was completed and two others are being constructed Many sensors were installed to monitor the behavior of retaining wall, braces as column in terms of stress change and displacement. Adjacent ground movement was also obtained. These projects demonstrate that SPS technology contributes to the speed as well as the economy involved in construction.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.33 no.10B
• /
• pp.865-875
• /
• 2008

In this paper, we propose a reliable multicast scheme for the tactical wireless ad hoc network where the members share the situation and operation data. Our scheme consists of two phases to guarantee the reliability. During the dissemination phase, we utilizes an epidemic approach similar to gossip-based ad hoc routing. Then the group members interchange the message reception state information periodically so that they are able to recover missing packets from the other members. We evaluate the performance of our scheme through extensive simulations using the network simulator in comparison with other existing reliable multicast schemes in mobile ad hoc network. Our scheme shows higher packet delivery ratio regardless of the mobility and imposes much lower control overhead to the non-group members compared with the existing schemes.

• Proceedings of the Korean Institute Of Construction Engineering and Management
• /
• 2008.11a
• /
• pp.291-296
• /
• 2008

For the past two decades, 3D/4D CAD research has heel mainly focused on the design and construction phase of a facility life-cycle. However, there has been a general notion that the strength of 3D/4D CAD lends itself to other phases such as planning, operation and maintenance. In this research, a 3D/4D CAD model was generated in a commercial software platform. Then, the traditional 1:fe cycle facility management procedures are reviewed to, see any possible improvement opportunity with the 3D/4D CAD model as an example. A focus group interview, in conjuction with an extensive literature review, produced the list of area where 3D/4D CAD model could significantly benefit the traditional life cycle facility practices. Finally, a questionnaire-based survey was conducted with 155 respondents to statistically verify the feasibility of 3D/4D CAD for life cycle facility management.

• 전자공학회논문지 IE
• /
• v.47 no.3
• /
• pp.41-46
• /
• 2010

WSN, or Wireless Sensor Network, consists of a multitude of inexpensive micro-sensors. Because the batteries in sensor nodes can not be replaced once they are deployed, the life of a WSN is absolutely determined by the batteries. So, energy efficiency of a network is a critical factor for long-life operation. LEACH protocol which divides WSN into two groups is a typical routing protocol based on the clustering scheme for the efficient use of limited energy. It is composed of round units which are separated into set-up and steady state. In this paper we propose a power saving scheme to minimize set-up phase itself and to involve a data comparison algorithm. We evaluate the performance of the proposed scheme in comparison with original LEACH protocol. Simulation results validate our scheme has better performance in terms of the number of alive nodes as time evolves and average energy dissipated.