• 한국정보기술응용학회:학술대회논문집
• /
• 한국정보기술응용학회 2005년도 6th 2005 International Conference on Computers, Communications and System
• /
• pp.229-232
• /
• 2005

In this paper, an image-based "approach-align -grasp" visual servo control design is proposed for the problem of object grasping, which is based on the binocular stand-alone system. The basic idea consists of considering a vision system as a specific sensor dedicated a task and included in a control servo loop, and we perform automatic grasping follows the classical approach of splitting the task into preparation and execution stages. During the execution stage, once the image-based control modeling is established, the control task can be performed automatically. The proposed visual servoing control scheme ensures the convergence of the image-features to desired trajectories by using the Jacobian matrix, which is proved by the Lyapunov stability theory. And we also stress the importance of projective invariant object/gripper alignment. The alignment between two solids in 3-D projective space can be represented with view-invariant, more precisely; it can be easily mapped into an image set-point without any knowledge about the camera parameters. The main feature of this method is that the accuracy associated with the task to be performed is not affected by discrepancies between the Euclidean setups at preparation and at task execution stages. Then according to the projective alignment, the set point can be computed. The robot gripper will move to the desired position with the image-based control law. In this paper we adopt a constant Jacobian online. Such method describe herein integrate vision system, robotics and automatic control to achieve its goal, it overcomes disadvantages of discrepancies between the different Euclidean setups and proposes control law in binocular-stand vision case. The experimental simulation shows that such image-based approach is effective in performing the precise alignment between the robot end-effector and the object.

• 한국전자통신학회논문지
• /
• 제2권1호
• /
• pp.10-18
• /
• 2007

본 논문에서는 MTS(Multiple Time Scale) 트래픽 제어 프레임워크를 TCP(Transfer Control Protocol) 기반의 신뢰할 수 있는 전송 및 윈도우 기반 혼잡제어로 확대 적용한다. 이 작업은 TCP의 대역폭 소비 반응의 적극성을 LTS 네트워크 상태의 함수 형태, 즉 RTT(Round-Trip Delay Time)가 결정한 피드백 루프의 한계를 넘어서는 정보의 형태를 조정하는 LTS(Large Time Scale) 모듈과 TCP를 연계시키는 방법으로 수행된다. 혼잡 제어 성능 평가 방식은 자기 유사성 네트워크 트래픽의 물리적 모델링으로부터 얻은 시뮬레이션 기반 하에서 결과를 나타낸다. 자기 유사 버스트 환경 하에서 RTT가 450ms일 때 소스 트래픽이 초과되지 않는 경우에 TCP-SSC(Selective Slope Control)의 성능 이득은 각각 ${\alpha}$가 1.05일 45%정도 높아지는 반면에 ${\alpha}$가 1.95일 때는 20%정도의 성능 이득을 얻을 수 있다. 그러므로 비율 기반 피드백 혼잡 제어에 TCP-MTS를 적용함으로서 TCP-SCC 처리 이득의 성능이 약 2배정도의 개선이 이루어짐을 시뮬레이션 결과로부터 알 수 있다.

• 전력전자학회논문지
• /
• 제17권3호
• /
• pp.238-245
• /
• 2012

This paper presents a sensorless speed control of a 2-phase switch reluctance motor(SRM). The proposed sensorless control scheme is based on the slide mode observer with parameter compensator to improve the estimation performance. In the stand still position, the initial rotor position is determined by pulse current responses of each phase windings and the current difference. In order to determine an accurate initial rotor position, the two initial rotor positions are estimated by the difference of the pulse currents. From the stand still to the operating region, a simple open loop control which determines the commutation sequence by the pulse current of the unexcited phase winding is used. When the motor speed is reached to the sensorless control region, the estimated rotor position and speed by the slide mode observer are used to control the SRM. The flux calculator used in the slide mode observer is designed by phase voltage and the voltage drops in the phase resistance of the winding. The accuracy of the flux calculator is dependent on the phase resistance. For the continuous update of the phase resistance, current gradient at the inductance break point is used in this paper. The error of the estimated rotor position at the current gradient position is used to update the phase resistance to improve the sensorless scheme. The proposed sensorless speed control scheme is verified with a practical compressor used in home appliances. And the results show the effectiveness of the proposed control scheme.

• Journal of Magnetics
• /
• 제19권1호
• /
• pp.90-100
• /
• 2014

Position estimation that uses only active phase voltage and current is presented, to perform high accuracy position sensorless control of a SRM drive. By extracting the amplitude of the first switching harmonic terms of phase voltage and current for a PWM period through Fast Fourier Transform (FFT), the flux-linkage and position are estimated without external hardware circuitry, such as a modulator and demodulator, which result in increased cost, as well as large position estimation error, produced when the motional back EMF is ignored near zero speed. A two-phase SRM drive system, consisting of an asymmetrical converter and a conventional closed-loop PI current controller, is utilized to validate the performance of the proposed position estimation scheme in comprehensive operating conditions. It is shown that the estimated values very closely track the actual values, in dynamic simulations and experiments.

• Journal of Power Electronics
• /
• 제15권5호
• /
• pp.1178-1189
• /
• 2015

A non-isolated Multiple Input Converter (MIC) with an input port, two storage ports and a load port is proposed. The synthesis of the proposed four port converter with its switch realization is presented. A steady state analysis of each operating mode with a small-signal model is derived, and a stability analysis is done. A mode selection controller is proposed to automatically choose a specific operating mode based on the voltage levels of the different source and storage units. In addition, a voltage control loop is used to regulate the output voltage. A 200W prototype is built with a TMS320F28027 DSP controller to test the feasibility of the operating modes. Simulation and experimental results show the ability of the proposed converter to handle multiple inputs either individually or simultaneously.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.505-507
• /
• 2004

This paper attempts to compensate the nonlinearity between the input voltage and the output displacement of the piezoelectric stack in dynamic actuation by the following two ways. Firstly, the charge steering by circuit configuration reduces the hysteresis of piezoelectric actuator remarkably. However, it makes the ripple in positioning due to the phase lag and noise induced from the elements of the long closed loop. Secondly, the feedforward control by neural network compensates the hysteresis of the piezoelectric actuators effectively with the appropriate selection of the input variables for the training. The improvement of the dynamic performance of the piezoelectric actuators by the developed linearization technique is verified by experiments.

• 전기학회논문지
• /
• 제59권1호
• /
• pp.168-175
• /
• 2010

The issue of rejecting periodic disturbances arises in various applications dealing with rotating machinery. A new method using DIDF (Dual-Input Describing Function) is presented for the rejection of periodic disturbances with uncertain frequency. This can be added to an existing feedback control system without altering the closed-loop system stability. The objective is to design a nonlinear compensator to secure specified oscillation amplitude and frequency which are the same as disturbances. We suggest two procedures to determine coefficients for DIDF's synthesis. The structure of the proposed DIDF is so simple that we can easily synthesize. A number of computer simulations were carried out to demonstrate the salient feature of the proposed DIDF compared to the conventional ones(that is, adaptive algorithms).

• Journal of Power Electronics
• /
• 제1권1호
• /
• pp.1-8
• /
• 2001

The elimination of a pole sensor is desirable due to the low-cost requirement, the compactness, and the applied drives. This paper proposes the algorithm for the initial pole-position estimation of a surface permanent magnet linear synchronous motor (PM-LSM), which is carried out under the closed loop control without a pole sensor and is insensitive to the motor parameters. This algorithm is based on the principle that the initial pole position (IPP) is estimated by the trigonometric function of the two reference currents. The effectiveness of the proposed algorithm is confirmed by testing a surface PM-LSM with large disturbance, which result shows that IPP is well estimated within a satisfied moving-distance and a shorter estimation taken-time even if large disturbance such as cogging and friction is existed.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 1993년도 Proceedings of International Conference for Agricultural Machinery and Process Engineering
• /
• pp.1137-1146
• /
• 1993

In order to analyze lateral control in the forward manuever of a tractor- trailer combination , a human operator model and a kinematic vehicle model were utilized for the operator/vehicle system. By combining the vehicle and operator models, a mathematical model of the closed-loop operator/vehicle system was formulated. A computer program was developed so as to simulate the motion of the tractor-trailer combination . In order to verify the operator/vehicle system model, the results of the field trials were compared with the simulated results. There was found to be reasonably good agreement between the two.

• Smart Structures and Systems
• /
• 제15권4호
• /
• pp.1041-1062
• /
• 2015

In this paper a method of finding optimal positions for piezoelectric actuators and sensors on different structures is presented. The genetic algorithm and multi-objective genetic algorithm are selected for optimization and $H_{\infty}$ norm is defined as a cost function for the optimization process. To optimize the placement concerning the selected modes simultaneously, the multi-objective genetic algorithm is used. The optimization is investigated for two different structures: a cantilever beam and a simply supported plate. Vibrating structures are controlled in a closed loop with feedback gains, which are obtained using optimal LQ control strategy. Finally, output of a structure with optimized placement is compared with the output of the structure with an arbitrary, non-optimal placement of piezoelectric patches.