• International Journal of Naval Architecture and Ocean Engineering
• /
• 제6권3호
• /
• pp.529-561
• /
• 2014

The two-phase turbulent flow past an interface-piercing circular cylinder is studied using a high-fidelity orthogonal curvilinear grid solver with a Lagrangian dynamic subgrid-scale model for large-eddy simulation and a coupled level set and volume of fluid method for air-water interface tracking. The simulations cover the sub-critical and critical and post critical regimes of the Reynolds and sub and super-critical Froude numbers in order to investigate the effect of both dimensionless parameters on the flow. Significant changes in flow features near the air-water interface were observed as the Reynolds number was increased from the sub-critical to the critical regime. The interface makes the separation point near the interface much delayed for all Reynolds numbers. The separation region at intermediate depths is remarkably reduced for the critical Reynolds number regime. The deep flow resembles the single-phase turbulent flow past a circular cylinder, but includes the effect of the free-surface and the limited span length for sub-critical Reynolds numbers. At different Froude numbers, the air-water interface exhibits significantly changed structures, including breaking bow waves with splashes and bubbles at high Froude numbers. Instantaneous and mean flow features such as interface structures, vortex shedding, Reynolds stresses, and vorticity transport are also analyzed. The results are compared with reference experimental data available in the literature. The deep flow is also compared with the single-phase turbulent flow past a circular cylinder in the similar ranges of Reynolds numbers. Discussion is provided concerning the limitations of the current simulations and available experimental data along with future research.

• 한국주조공학회지
• /
• 제17권5호
• /
• pp.465-471
• /
• 1997

An integrated computer program consisting of a pre-processor, main solver, and post-processor was developed for the design of large steel castings. The pre-processor, based on the AutoCAD, enables the user to produce approval drawings, casting design drawings and mesh diagrams in sequence using a personal computer. In the main solver, two numerical models were employed; one models the fluid flow during mold filling, and the other models the heat transfer and solidification. The post-processor can be used to present simulation results such as flow pattern, mold filling sequences, solidification times, temperature gradients and location of shrinkage defects by color graphics. In order to validate the applicability of the present integrated program, a series of experiments on simple-shaped steel castings were carried out. After the validation of the present model, it was applied to the casting design of the large steel anchor of an SC42 alloy. Various solidification parameters such as a temperature distribution and a solidification time in the casting and the mold were compared with those obtained experimentally. Simulated results predicting shrinkage defects were in good agreement with those obtained experimentally. It was found that the present method can be successfully applied to the quantitative casting design for complex-shaped large steel castings.

• 대한기계학회논문집B
• /
• 제26권2호
• /
• pp.278-287
• /
• 2002

The objective of the paper was to calculate the pressure drop and to investigate the recirculation region of the conical orifices used in Kwang-yang Iron & Steel Company. The flow field with water used as a working fluid was the turbulent flow for Reynolds number of 2$\times$10$^4$. The effective parameters fur the pressure drop and the recirculation region were the conical orifice\`s inclined angle ($\theta$) against the wall, the interval(S) between orifices, the relative angle of rotation($\alpha$) of the orifices, the shape of the orifice's hole(circle, rectangle, triangle) having the same area, the number(N) of the orifice's holes having the same mass flow rate, and the thickness(t) of the orifices. It was fecund that the shape of the orifice's hole, the number of the orifice's holes and the thickness of the orifice affected the total pressure drop a lot and that the conical orifice's inclined angle against the wall, the relative angle of rotation of the orifices, the number of the orifice's holes and the thickness of the orifices affected the center location of the recirculation region. The PISO algorithm with FLUENT code was employed to analyze the flow field.

• 한국소음진동공학회논문집
• /
• 제23권7호
• /
• pp.597-604
• /
• 2013

Underwater acoustic sensors are significantly damaged from underwater explosion. The damage that affects sensor should be evaluated for its smooth operations and safety. For satisfying these objectives, it is necessary to obtain more accurate values of the pressure and the energy flux density by distance. This paper is divided into two part. First, to obtain more accurate value of the pressure and the energy flux density at each point, the simulation results and the reference values were compared. For fitting to the reference pressure and the reference energy flux density, the sizes of fluid and TNT model are corrected, and the comparison results show good agreements. Second, based on these results, the structural integrity of underwater sensor structure was analyzed when TNT located in 10 meters from underwater sensors structure. This simulation used the commercial software MSC/DYTRAN.

• 한국추진공학회지
• /
• 제22권2호
• /
• pp.66-73
• /
• 2018

밀폐용기 내 Zirconium/Potassium Perchlorate의 연소를 수치적 모델링을 통해 전산해석을 수행하였다. 5차 WENO 공간차분법과 improved delayed detached eddy (IDDES) 난류모델을 사용하여 충격파가 동반되는 내부 유동구조를 모사하였고, 라그랑지안 연소모델을 통해 화약 입자를 계산하였다. 옆면 중앙에 센서가 설치된 원통형 밀폐용기 내부 유동분석을 통해 압력 진동이 발생하는 원인을 규명하였다. 또한 센서 다이어프램 깊이 변화에 따라 측정되는 압력 데이터를 실험값과 비교분석 하였다. 그 결과 센서 탭의 깊이가 약 2.36 mm 이상으로 커지면 유동속도가 아음속으로 감쇠하고 복잡한 eddy가 발생하여 측정값에 큰 불규칙성을 야기하는 현상을 관측하였다.

• 대한토목학회논문집
• /
• 제41권4호
• /
• pp.331-340
• /
• 2021

본 논문은 비예측 극한하중인 폭발하중에 노출된 RC building 구조물의 폭발손상평가를 위한 수치해석적 연구이다. 수치해석의 효율성 및 정확성을 높이기 위해, 폭발하중에 대한 정의, 유체-구조 연성을 위한 Euler-Lagrange 커플링 기법 적용, 그리고 고변형률 속도가 고려된 콘크리트 및 강재 재료구성모델이 제안된다. 특히 효율적인 폭발하중 정의를 위해, Euler-FCT 기법을 통하여 TNT 질량에 따른 시간별 압력하중 데이터가 확보되고, 이는 RC building 구조물 총 7 지점의 폭발위치에 적용되며, ANSYS-AUTODYN 솔버에 연결되어 수치 시뮬레이션이 수행된다. 해석결과, TNT 질량 및 폭발 위치에 따라 손상 차이가 발생하였으며, 먼저 TNT 질량 20 kg 일 경우 3 곳의 폭발손상 지점에서 주부재 중 슬래브에서만 중간 및 가벼운 손상이 발생되었고, TNT 질량 100 kg 일 경우 5 곳의 폭발손상 지점 중 3 곳은 슬래브 및 보 부재에서 중간 손상이 발생되었으며, 2 곳은 슬래브에서 심각한 손상이 발생되었다.

• Tribology and Lubricants
• /
• 제35권2호
• /
• pp.99-105
• /
• 2019

This study presents an experimental investigation of the wear and oxidation of the bristles of a brush seal in a super-heated steam environment. We construct a model reflecting normal force and radial interference to predict the amount of wear. To monitor the volume loss of the bristle induced by the swirl phenomenon of the rotor, we measure the clearance between the rotor and the brush seal by using a non-contact 3-D device. We calculate the area by using the area-wise measurement method. Considering the obvious brush seal wear variables, we use two disks with different roughness($Ra=0.1{\mu}m$ and $100{\mu}m$) to determine the effect of roughness on wear. Considering an actual steam turbine, we utilize a steam generator and super-heater to generate a working fluid (0.95MPa, 523.15K) that has high kinetic energy. We observe the abrasion of the bristles in the hot steam environment through a scanning electron microscope image. This study also conducted energy dispersive X-ray (EDX) analysis for a qualitative evaluation of local chemistry. The results indicate that the wear and elimination of bristles occur on the disk with high roughness, and the weight increases due to oxidation. Furthermore these results, reveal that the bristle oxidation is accelerated more under super-heated steam conditions than under conditions without steam.

• 한국수소및신에너지학회논문집
• /
• 제32권4호
• /
• pp.228-235
• /
• 2021

Polymer electrolyte membrane fuel cells (PEMFC) are currently being used in various transport applications such as drones, unmanned aerial vehicles, and automobiles. The power required is different according to the type of use, purpose, and the conditions adjusted using a cell stack. The fuel cell stack is compressed to reduce the size and prevent fuel leakage. The unit cells that make up the cell stack are subjected to compression by clamping force, which makes geometrical changes in the porous media and it impacts on cell performance. In this study, finite elements method (FEM) and computational fluid dynamics (CFD) analysis for the deformed unit cell considering the effects of clamping force is performed. First, structural analysis using the FEM technique over the deformed gas diffusion layer (GDL) considering compression is carried out, and the resulting porosity changed in the GDL is calculated. The PEMFC model is then verified by a three-dimensional, two-phase fuel cell simulation applying the physical properties and geometry obtained before and after compression. The detailed simulation results showed different concentration distributions of fuel between the original and deformed geometry, resulting in the difference in the distribution of current density is represented at compressed GDL region with low oxygen concentration.

• 한국산업융합학회 논문집
• /
• 제25권1호
• /
• pp.61-70
• /
• 2022

Fire damage time in high-rise buildings and wildland fire increasing every year. The use of high-pressure fire pumps is required to effectively extinguish fires. Reflecting the curvature effect of the fire hose occurring at the actual fire fighting site, this study provides a database of pressure drop, discharge velocity and maximum discharge height through C FD numerical analysis and it can provide using standards for fire extinguishing. Two Reynolds numbers of 200000 and 400000 were numerically analyzed at 0° -180° bending with water of 25℃ as a working fluid in hoses with a diameter of 65mm, a length of 15m, and a radius of curvature of 130mm. Realizable k-ε turbulence model was used and standard wall function was used. The pressure drop increases as the bending angle increases, and the maximum value at 90° and then decreases. The increasing rate is greater than the decrease. The velocity of the secondary flow also decreases after having the maximum value at 90°. The decreasing rate is greater than the increase. The turbulent kinetic energy increases to 120° and decreases with the maximum value. Pressure drop, velocity of the secondary flow, and turbulence kinetic energy are measured larger in the second bending region than in the first bending region.

• Membrane and Water Treatment
• /
• 제13권5호
• /
• pp.235-243
• /
• 2022

The paper presents the effect of operating temperatures and flow rates on the distillate flux that can be obtained from a hydrophobic membrane having the characteristics: pore size of 0.15 ㎛; thickness of 130 ㎛; and 85% porosity. That membrane in the present investigation could be the direct contact (DCMD) or the air-gap membrane distillation (AGMD). To model numerically the membrane distillation processes, the two-dimensional computational fluid dynamic (CFD) is used for the DCMD and AGMD cases here. In this work, DCMD and AGMD models have been validated with the experimental data using different flows (Parallel and Counter-current flows) in non-steady-state situations. A good agreement is obtained between the present results and those of the experimental data in the literature. The new approach in the present numerical modeling has allowed examining effects of the nature of materials (Polyvinylidene fluoride (PVDF) polymers, copolymers, and blends) used on thermal properties. Moreover, the effect of the area surface of the membrane (0.021 to 3.15 ㎡) is investigated to explore both the laminar and the turbulent flow regimes. The obtained results found that copolymer P(VDF-TrFE) (80/20) is more effective than the other materials of membrane distillation (MD). The mass flux and thermal efficiency reach 193.5 (g/㎡s), and 83.29 % using turbulent flow and an effective area of 3.1 ㎡, respectively. The increase of feed inlet temperatures and its flow rate, with the reduction of cold temperatures and its flow rate are very effective for increasing distillate water flow in MD applications.