• Applied Biological Chemistry
• /
• 제34권1호
• /
• pp.75-76
• /
• 1991

Bran structure and gelatinization property of upland and lowland japonica waxy brown rice were compared. Dimension, weight and number of aleurone layer were similar between upland(Nonglimna 1) and lowland(Shinsunchalbyeo) rices, but the aleurone layer and pericarp of upland rice were thicker. Water uptake rate of upland rice at $60^{\circ}C$ was lower than that of lowland one. There was no difference in intrinsic viscosity between two rice starches. Upland rice starch had lower onset temperature, narrower gelatinization temperature and lower water content lot gelatinization compared with lowland rice starch.

• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 1997년도 추계 학술발표회 논문집 Proceedings of EESK Conference-Fall 1997
• /
• pp.133-140
• /
• 1997

Based on the Green's function technique, an analytical approach is developed to examine the surface wave screening effectiveness of composite wave barriers. The composite barrier consists of a high velocity layer sandwiched between two thin layers of low shear velocity materials. The high velocity layer is represented by differential matrix operators which relate the wave fields on each side of the layer. The low velocity layers are modeled by non-rigid contact conditions which allow partial sliding at the interfaces. Screening ratio of barriers with various combination of material, geometric, and non-rigidness parameters are compared and discussed in some detail.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2007년도 7th International Meeting on Information Display 제7권1호
• /
• pp.261-264
• /
• 2007

We developed a non self-aligned poly-silicon TFTs fabrication process at two different temperatures on spin-coated polyimide layer above Si-wafer. After TFTs fabrication, the polyimide layer was mechanically released from the Si-wafer and the devices characteristics were compared. In addition self-heating and hot-carrier induced instabilities were analysed.

• 전기학회논문지P
• /
• 제51권4호
• /
• pp.193-197
• /
• 2002

In this paper, the ultrasonic sensor for gas flowmeter was simulated, fabricated and measured according to the assembly step and the piezoelectric vibrator layers. The simulated resonant frequency and the measured resonant frequency were similar except two layer sensor. The simulated resonant frequency of three layer sensor was 48 kHz and the measured resonant frequency of three layer sensor was 45.2 kHz. From the results, the ultrasonic sensor for gas flowmeter could be designed and expected without fabrication.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2002년도 하계종합학술대회 논문집(1)
• /
• pp.383-386
• /
• 2002

The goal of this study is to realize the PBG lowpass filter using novel PBG structure modification both upper layer and ground layer. It has been designed three aperture slots of ground layer for PBG structure which the center slot shape of ground is two type, rectangular and dumbbell. This PBG LPF llas the character of the broader stopband and smaller size than typical LPF. The measurement results have matched the simulated ones. It has the cutoff frequency of each 4.4650Hz and 3.520Hz and at least -2OdB of the signal suppression at the stopband.

• 한국정밀공학회지
• /
• 제5권1호
• /
• pp.29-39
• /
• 1988

Plastically deformed layer beneath metal surface machined by orthogonal cutting was evaluated in terms of residual stress, microvickers hardness, side spread, and the side strain. An attempt was made to predict the depth of layer according to machining conditions particularly tool geometry and the shear plane angle. In this paper, we employed two models concerning the sliplines. The exact model was validated by comparision of computed and measured tool force and its angle, and the model offers an upper boundary of the deformed layer to be in good agreement with the experiment.

• 한국화재소방학회:학술대회논문집
• /
• 한국화재소방학회 1997년도 International Symposium on Fire Science and Technology
• /
• pp.625-632
• /
• 1997

A two-dimensional zone-like model is developed to predict the interaction between hot gas layer and water droplets after sprinkler activation. The model combines the motion equations for each droplet with heat and mass transfer between the gas and water. The results indicate that negative buoyancy in the hot layer can only be obtained if the initial temperature profile is uniform. If an experimental profile Is used instead, positive buoyancy results. This conclusion has been confirmed with experimental data.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 D
• /
• pp.1544-1546
• /
• 1999

The fabrication process for ceramic fuel cell with a large electrode area was investigated. A cofired cell of two layer, electrolyte/anode, yielded a power of $200mW/cm^2$. Its performance loss was mainly due to iR drop in the anode side. The performance of the cofired of three layer. cathode/electrolyte/ anode, was much lower than that of two layer, which resulted from the large iR drop and overvoltage at the cathode side. Also a flat cell with a large area of $7.7{\times}10.8cm^2$ was fabricated successfully and tested using ceramic and metallic interconnectors. The large cell with metallic interconnectror showed a good performance of 0.6 V, 4.5 A.

• Structural Engineering and Mechanics
• /
• 제18권4호
• /
• pp.441-459
• /
• 2004

This paper explores the potential use of neural networks (NNs) in the field of contact mechanics. A neural network model is developed for predicting, with sufficient approximation, the contact lengths between the elastic layer and two elastic circular punches. A backpropagation neural network of three layers is employed. First contact problem is solved according to the theory of elasticity with integral transformation technique, and then the results are used to train the neural network. The effectiveness of different neural network configurations is investigated. Effect of parameters such as load factor, elastic punch radii and flexibilities that influence the contact lengths is also explored. The results of the theoretical solution and the outputs generated from the neural network are compared. Results indicate that NN predicted the contact length with high accuracy. It is also demonstrated that NN is an excellent method that can reduce time consumed.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 추계학술대회 논문집
• /
• pp.159-159
• /
• 2009

We characterize a flexible self-assembled liquid crystal display (LCD) fabricated from a polyimide (PI) alignment layer with polydimethylsiloxane pixel walls. Ion beam (IB) irradiation aligned LC molecules in the PI layer and bonded two flexible plastic substrates in a one-step assembly of the pixel walls. X-ray photoelectron spectroscopic analysis, Fourier transform infrared spectroscopy, and scanning electron microscopy provided chemical and physical evidence for the formation of stable chemical bonds between the PI layer and the PDMS pixel walls in addition to the important maintenance of a uniform 6 um gap between the two substrates without the use of any epoxy resins or other polymers.