• 대한기계학회논문집A
• /
• 제24권2호
• /
• pp.403-410
• /
• 2000

The effects of various factors were studied on the process of a steel cord by twisting wires. To remove residual twisting moment after the steel cord process, the twisting angles of residual elasti c twisting and overtwisting were measured and compared with finite element results. The agreement between experimental data and finite element calculations was good for the angles of residual elastic twisting and over-twisting. The stress distributions in a steel cord under complex loading conditions were also obtained by using the finite element analysis.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 춘계학술대회논문집
• /
• pp.115-118
• /
• 1999

The twisting and bending extrusion process is developed by the $DEFORM^TM$-3D. Because the rectangular section of the extruded product has the symmetry line of cross-section area, the twisting and the bending of extruded product has not occurred. The product with the rectangular section is applied to the twisting and bending extrusion process through the twisted die surface and eccentricity die section. It is shown that the twisting of extruded product is caused by the twisted die surfaces and the bending of extruded product is causd by the eccentricity between the die section. The results by the analysis show that the twisting angle and the curvature of extruded products increases by the die twisting angle, the eccentricity, but decreases by the die length, and friction condition

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1998년도 춘계학술대회논문집
• /
• pp.254-257
• /
• 1998

The twisting and the bending of extruded product are caused by the shapes of products and by the shapes of die surfaces and by the shapes of die land. Because the elliptical shape and the circular shape of the extruded product have the symmetry line of cross-section area, the twisting and the bending of product has not occurred. But the analysis by the DEFORM-3DTM show that the twisting and the bending of extruded product can be occurred by the twisting of the twisting of the die land and by the curving of the die land. The results by the analysis show that the twisting angle of the extruded procduct increases by the twisting angle of the die land and the curvature of the extruded products increases by the radius of bending of the die land.

• 소성∙가공
• /
• 제20권2호
• /
• pp.104-109
• /
• 2011

The metal front case of a mobile phone is manufactured by press forming and welding of thin metal sheets. Twisting of the frame after the forming process is one of main obstacle for the assembly with reinforcement by welding. This study introduces a method preventing twisting of the metal front case frame in press forming. The spring-back after forming produces twisting of the frame, which leads to a low structural stiffness. To reduce twisting, connectors are required to reinforce the structural stiffness of the frame. In this study, the twisting profile is evaluated using a finite element(FE) analysis for various connector shapes. The actual connector shape is determined by minimization of the frame twisting within the tolerance of the FE-analysis. To verify the validity of the proposed blank shape, a forming experiment is performed and the twisting profile is measured using a 3D laser scanning method. The dimensional accuracy is found to be within the tolerance and in good agreement with the FE-analysis.

• 대한인간공학회지
• /
• 제20권2호
• /
• pp.71-82
• /
• 2001

Twisting posture in lifting tasks has been identified as a risk factor of low back pain. However, it has been usually estimated in terms of compressive stress or muscular activity. Thus, this study was conducted to predict the influence on muscular fatigue during lifting simulation. Fifteen young and healthy subjects were recruited and performed isometric trunk exertions during upright standing, two-level flexions and five-level asymmetric twisting conditions. EMG signals from five primary trunk muscles in right part of body were collected during 20sec for 45 different lifting conditions. RMS(root mean square) and MPF(mean power frequency) parameters were used to analyze the EMG signals. Twisting postures were significant in right erector spinae(ERSR), right latissimus dorsi(LATR), right internal oblique(INOR) for muscular activities. Especially, when trunk was $30^{\circ}$ CCW twisting posture. ERSR and INOR activities increased respectively by 11% and 3%. Regarding the trunk muscle fatigue, we found that MPF shifts in twisting posture increased 2.3 and 2.6 times for ERSR and INOR muscles respectively. Therefore, It is probable for workers to suffer from low back disorders when they were exposed to a extreme twisting posture during prolonged lifting. This study suggests NIOSH(National Institute for Occupational Safety and Health) lifting equation needs the time-duration multiplier in addition to asymmetric multiplier.

• 소성∙가공
• /
• 제10권4호
• /
• pp.302-310
• /
• 2001

The twisting and extrusion process of the product with involute helical fin from the round billet is developed by the upper bound analysis. The twisting of extruded product is caused by the twisted inclined die surface connecting the die enterance section and the die exit section linearly. In the analysis, the internal shear surface is defined as the curved twisted plane from the twisting of die surface and the shear work is calculated by the consumption of shear energy. The increase rate of angular velocity is determined by the minimization of plastic work. The angular velocity of die exit can be controlled by the land length and the length of inclined die. The alular velocity assums to be increased linearly by the axial distance from the die enterance to the die exit. The results of the analysis show that the angular velocity of the extruded product increases with the die twisting angle, the reduction of area, and decreases with the die length, the friction constant.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• 제33권5호
• /
• pp.375-384
• /
• 2011

Purpose: The advent of microsurgical technique and instruments, particularly in the field of perforator flap and supermicrosurgery, which have expanded the scope of microsurgery. However, supermicroanastomosis without any compression, tension, or distortions must be achieved to reach successful outcomes. Small-caliber vessels, such as those with an internal diameter less than 0.2 mm, are susceptible to inadvertent twisting of the anastomosis. In this study, using the superficial inferior epigastric artery (SIEA)-based flap model in Sprague-Dawley (SD) rats, we evaluated the acceptable limits of twisting effects on supermicroanastomotic sites. Methods: A total of 20 supermicroanastomoses were performed using the SIEA-based flap model in 10 male SD rats, 10-weeks-of-age, weighing 300~350 g. Rats were divided into five groups of two with four flaps as follows: 1) sham, 2) control group with end to end SIEA arterial supermicroanastomosis, 3) experimental I (EA1) with $90^{\circ}$ twisting, 4) experimental II (EA2) with $180^{\circ}$ twisting, and 5) experimental III (EA3) with $270^{\circ}$ twisting of the supermicroanastomosis. Each SIEA was anastomosed using six 11-0 $Ethilon^{(R)}$ (Ethicon Inc. Co., NJ, USA) stitches except in the sham group where the SIEA was only clamped with Supermicro vascular $clamps^{(R)}$ (S&T, Neuhausen, Switzerland) for 20 minutes. Results: The anastomosed arterial patency showed no remarkable changes according to doppler waveforms measured with a Smardop 45 Doppler System (Hadeco Inc., Kawasaki, Japan). The pulsatility index (PI) was increased at postoperative day 10 in the EA2 and EA3 groups, and the resistance index (RI) showed no statistically significant difference between preoperative and postoperative values at 10 days. Histologic specimens from the EA3 group showed increased tunica media necrosis, convolution of the internal elastic lamina, densely packed platelets, fibrin, and erythrocytes. Flap viability and anastomosed vessel patency were not significantly affected by the degree of arterial twisting in this study, other than in the EA3 group where minor effects on arterial patency of the microanastomoses were encountered. Conclusion: It appears that minor twisting on small caliber arteries, used in supermicroanastomoses, can be tolerated. However, twisting should be avoided as much as possible, and more than $180^{\circ}$ twisting must be prevented in clinical practice.

• 한국염색가공학회지
• /
• 제18권1호
• /
• pp.33-43
• /
• 2006

The purpose of this study was to eximine the effect of different yam twisting methods on mechanical properties and 3D CAD images of plain knitted fabrics made of composite yarns. Six yams were used in this study: four different composite yams of the six consist of acetate and functional polyester (Poly-m) with the ratio of 70:30, and the rest two are the original acetate $100\%$ yam and the poly-m $100\%$ yarn. The four kinds of composite yarns were processed in combinations of twisting processes such as interlacing, false twisting, two for one twisting, combined twisting and single covering, and the two original yams were knitted without any twisting process. Sixteen mechanical properties of all the six knitted fabrics, knitted under the same knitting conditions, were measured by KES-FB system with the outer knit condition. The results were as follows; 1) When the sample applied with the false twisting process at the temperature as high as $220^{\circ}C$, ENT, B, HB, G and RC values of samples increased which leads to increasing dimensional stability. 2) To gain the high bending and shear properties in the single covering process, selecting the core yarn with such properties is the most important factor. 3) Interlacing process effected to increase RC value. 4) False twisting process after interlacing process gave bulkiness and un-interlaced part in yam was increased SMD value. The SMD value of the kilted fabric of the composite yarn, which was put through the combined twist process, was higher than those of which simple process such as the two for one twist or the single covering process applied. In order to achieve the silk-like surface feel of knitted fabric, the sin91e covering process is recommended. 5) Examining the simulation images of the knifed fabrics of composite yarn, which were generated by the 3D CAD system based on the mechanical properties of the fabric, led that appearance could be changed as different twisting methods were applied.

• 한국잠사곤충학회지
• /
• 제46권1호
• /
• pp.38-43
• /
• 2004

1. 명주실현의 제조법을 구명하고자 상연과 하연의 꼬임수를 달리하여 시험한 결과 강력은 꼬임수가 적을수록 증가하였고 하연보다도 상연의 꼬임수의 영향이 컸다. 신도는 강도와 정반대의 결과를 나타내었다. 평균 하중에 대하여 60%에 대한 탄성반복회수는 강력과 같은 경향이었고 그 차이가 뚜렷하였고 탄성 신장률은 신도와 비슷한 경향이었다. 탄성률은 강도와 같이 꼬임수가 증가할수록 저하되었다. 관능평가 결과 꼬임수가 적으면 농현이 부족하여 어느 정도 이상의 꼬임이 필요하였다. 2. 명주실의 하연 정도가 물성에 미치는 영향을 조사하기 위하여 상연의 꼬임수를 고정하고 하연의 꼬임수를 달리한 결과 꼬임수가 많아질수록 현의 강력은 감소하였고 신도는 증가하였다. 현의 탄성률은 강력과 비슷한 경향을 나타내었다. 3. 상연중에 하연의 꼬임수를 주지 않을 때는 현의 강력이 순차적으로 커지고 하연의 꼬임수를 상연 꼬임속도의 85%를 줄 경우에는 현의 강력이 순차적으로 감소하였다. 그러나 하연의 꼬임수를 상연속도의 40% 줄 경우에는 현의 처음이나 마지막의 강력이 일정하게 유지하게 됨을 알 수 있었다.

• 충청수학회지
• /
• 제11권1호
• /
• pp.99-113
• /
• 1998

Let (H, K) be a paired Hopf algebras and let A be arbitrary left H-module coalgebra. We construct twisting coproduct on $A{\otimes}K$. We show that the well known construction of the smash coproduct can be viewed as a particular case of the construction above.