• 대한기계학회논문집B
• /
• 제23권6호
• /
• pp.753-760
• /
• 1999

Experiments were conducted to investigate the effect of the initial turbulent intensity on the flow and heat transfer characteristics for a two-dimensional impinging jet. A square rod was installed at the nozzle exit to increase initial turbulent intensity. A hot wire probe and thermochromic liquid crystal technique were used to measure the turbulent intensity and the surface temperature. All measurements were made over a range of nozzle-to-plate distance from 1 to 10 at Re=20,000. When the rod is not installed, the maximum stagnation point Nusselt number is occurred at H/B=9. A higher initial turbulent intensity enhanced the heat transfer on the surface. A correlation between stagnation point Nusselt number and turbulent intensity are presented.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2007년도 춘계 학술대회논문집
• /
• pp.159-162
• /
• 2007

This study presents a numerical procedure to optimize the shape of a staggered dimpled surface to enhance the turbulent heat transfer in a rectangular channel. A optimization technique based on neural network is used with Reynolds-averaged Navier-Stakes analysis of the fluid flow and heat transfer with Shear Stress Transport turbulence model. The dimple depth-to-dimple print diameter ratio, channel height-to-dimple print diameter ratio, and dimple print diameter-to-pitch ratio are chosen as design variables. The objective function is defined as a linear combination of terms related to heat transfer and friction loss with a weighting factor. Latin Hypercube Sampling is used to determine the training points as a mean of the Design of Experiment. Optimal values of the design variables were obtained in a range of the weighting factor.

• 대한기계학회논문집B
• /
• 제24권1호
• /
• pp.1-8
• /
• 2000

A modified low-Reynolds-number Reynolds stress model is developed for the calculation of drag-reducing turbulent flows induced by polymer injection. The results without polymer injection are compared with the results of direct numerical simulation to ensure the validity of the basic model. In case of drag reduction, profiles of mean velocity and Reynolds stress components, in two-dimensional channel flow, obtained with a proper value of viscosity ratio are presented and discussed. Computed mean velocity profile is in very good agreement with experimental data. And, the qualitative behavior of Reynolds stress components with the viscosity ratio is also reasonable.

• 대한기계학회논문집
• /
• 제16권11호
• /
• pp.2111-2118
• /
• 1992

본 연구에서는 원관 내 및 평판 위의 흐름에 있어서 잘 확립된 벽면의 법칙을 적용하여 봉다발의 열전달계수를 예측하여 보고자 한다.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2008년도 12th Asian Congress of Fluid Mechanics
• /
• pp.39.1-39.1
• /
• 2008

• 대한기계학회논문집B
• /
• 제24권9호
• /
• pp.1255-1263
• /
• 2000

In this study, the modification of turbulent boundary layer flow by local wall vibration is investigated. The wall is locally vibrated using a wall deformation actuator, which moves up and down at the frequencies of 100Hz and 50Hz. Simultaneous measurements of the streamwise velocities in the spanwise direction are performed at several wall-normal and streamwise locations using an in-house multi-channel hot wire anemometer and a spanwise hot-wire-probe rake. The mean velocity is reduced in most places due to the wall vibration and its reduced amount becomes small as flow goes downstream. Interestingly, the mean velocity is found to increase very near the wall and near the actuator. This is due to the motion induced by the streamwise vortices which are generated by the downward motion of the actuator. In case of the streamwise velocity fluctuations, their magnitude increases as compared to the unperturbed turbulent boundary layer, and the increased amount becomes small as the flow moves downstream. The modified flow field at the forcing frequency of 50Hz is not much different from that of 100Hz, except the reduced amount of modification.

• 한국수자원학회논문집
• /
• 제44권5호
• /
• pp.417-427
• /
• 2011

침수식생 개수로 흐름은구조적으로상부영역과식생영역으로구분되는데, 상부영역은 일반 개수로의 흐름특성을 보이며 식생영역은 줄기에 의해 난류가 억제되어 정수식생 조건의 흐름과 유사하게 단순한 흐름특성을 보인다. 본 논문은 침수식생 개수로 흐름의 난류 및 유사이동 특성에 관한 실험연구이다. 이를 위해 폭 0.5m, 길이 12m인 개수로 실험장치를 이용하여수리실험을 실시하였다. 다양한 유량에 대하여 수심비 2～3인 흐름을 구현하였고, 나무원형 실린더를 이용하여 식생을 재현하였다. 평형상태에서 부유사 농도 분포를 측정하기 위해서중앙입경이 75 ${\mu}M$인 모래를 한계조건에 도달하기까지 지속적으로 투입하였다. 유속 성분의 계측을 위하여 레이저 도플러 유속계를 사용하였고, 튜브를 이용한 사이포닝 방식으로 시료를 직접 채취하여 부유사 농도를 측정하였다. 측정된 자료를 이용하여 실험조건에 따른 평균흐름과 난류량의 특성을 살펴보았고, Rouse 수에 따른 부유사 농도 분포를 제시하였다.

• Journal of Mechanical Science and Technology
• /
• 제20권11호
• /
• pp.1993-2001
• /
• 2006

The piezoelectric bimorph film, which, as an actuator, can generate more effective displacement than the usual PVDF film, is used to control the turbulent boundary-layer flow. The change of wall pressures inside the turbulent boundary layer is observed by using the multi-channel microphone array flush-mounted on the surface when actuation at the non-dimensional frequency $f_b^+$:=0.008 and 0.028 is applied to the turbulent boundary layer. The wall pressure characteristics by the actuation to produce local displacement are more dominantly influenced by the size of the actuator module than the actuation frequency. The movement of large-scale turbulent structures to the upper layer is found to be the main mechanism of the reduction in the wall- pressure energy spectrum when the 700$700{\nu}/u_{\tau}$-long bimorph film is periodically actuated at the non- dimensional frequency $f_b^+$:=0.008 and 0.028. The biomorph actuator is triggered with the time delay for the active forcing at a single frequency when a 1/8' pressure-type, pin-holed microphone sensor detects the large-amplitude pressure event by the turbulent spot. The wall-pressure energy in the late-transitional boundary layer is partially reduced near the convection wavenumber by the open-loop control based on the large amplitude event.

• 대한기계학회논문집
• /
• 제16권8호
• /
• pp.1545-1551
• /
• 1992

본 연구에서는 벽면의 법칙(law of the wall)을 이용하여 봉다발의 난류 마찰 계수를 예측하는 간단한 방법이 제안되었다. 이 방법은 전체 유로를 요소 유로로 나 누고 각 요소유로에 벽면의 법칙을 적용하여 마찰 계수를 구한다.이 방법을 사용 하면 마찰 계수가 간단한 산술식의 형태로 나타나므로 복잡한 형상의 봉다발의 마찰 계수도 손쉽게 구할 수 있다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제29권3호
• /
• pp.281-289
• /
• 2005

An experimental study on the heat transfer and friction characteristics of a fully developed turbulent air flow in a square channel with $45^{\circ}$ inclined ribs on one, two, and four walls is reported. Tests were performed for Reynolds number ranging from 7,600 to 24,900. The pitch-to-rib height ratio, p/e, was kept at 8 and rib height-to-channel hydraulic diameter ratio, $e/D_h$, was kept at 0.0667. The heat transfer coefficient and friction factor values were enhanced with the increase in the number of ribbed walls. Results of this investigation could be used in various applications of internal channel turbulent flows involving different number of roughened walls.