• 한국음향학회:학술대회논문집
• /
• 한국음향학회 2002년도 하계학술발표대회 논문집 제21권 1호
• /
• pp.465-468
• /
• 2002

An unconstrained tuning fork with a 3-D model has been numerically analyzed by Finite Element Method (FEM) and Boundary Element Method (BEM). The first three natural frequencies were calculated by the FEM modal analysis. Then the change of the modal frequencies was examined with the variation of the tuning fork length and width. Analytical model equations were derived from the numerically relating results of the modal frequency-tuning fork length by approximating minimization. Finally the BEM was used for the sound pressure field calculation from the structural displacement data.

• 한국소음진동공학회논문집
• /
• 제13권2호
• /
• pp.92-98
• /
• 2003

A rate gyroscope has been used popularly to measure the angular motion of a given vehicle using a symmetric rotor spinning rapidly about its symmetry axis. Since the rapid rotation is required in this type of gyroscope, the motor has been used to make the rotor spin, so that it results in a heavy configuration. The toning-fork gyroscope has been developed to avoid this problem, which utilizes a Coriolis coupling term and vibration about one axis. Due to the Coriolis effect, the vibration of one axis is transferred to other axis when the angular motion along the vibrating axis is given to the system. The concept of a tuning-fork gyroscope was recently realized using MEMS techniques. However, the dynamic characteristics of the tuning-fork gyroscope has not been discussed in detail. In this study. we derived the equations of motion for the tuning-fork type gyroscope using the energy approach and investigated the dynamic characteristics by means of numerical analysis.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2001년도 추계 학술발표강연 및 논문개요집
• /
• pp.84-84
• /
• 2001

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2000년도 추계학술발표강연 및 논문개요집
• /
• pp.90-90
• /
• 2000

• The Journal of the Acoustical Society of Korea
• /
• 제22권1E호
• /
• pp.11-18
• /
• 2003

Non-singular boundary element method (BEM) codes are developed in acoustics application. The BEM code is then used to calculate unknown boundary surface normal displacements and surface pressures from known exterior near field pressures. And then the calculated surface normal displacements and surface pressures are again applied to the BEM in forward in order to calculate reconstructed field pressures. The initial exterior near field pressures are very well agreed with the later reconstructed field pressures. Only the same number of boundary surface nodes (1178) are used for the initial exterior pressures which are at first calculated by Finite Element Method (FEM) and BEM. Pseudo-inverse technique is, used for the calculation of the unknown boundary surface normal displacements. The structural object is a tuning fork with 128.4 ㎐ resonant. The boundary element is a quadratic hexahedral element (eight nodes per element).

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문집
• /
• pp.306-311
• /
• 2002

Non-singular boundary element method (BEM) codes are developed in acoustics application. The BEM code is then used to calculate unknown boundary surface normal displacements and surface pressures from known exterior near Held pressures. And then the calculated surface normal displacements and surface pressures are again applied to the BEM in forward in order to calculate reconstructed field pressures. The initial exterior near field pressures are very well agreed with the later reconstructed field pressures. Only the same number of boundary surface nodes (1178) are used far the initial exterior pressures which are initially calculated by Finite Element Method (FEM) and BEM. Pseudo-inverse technique is used for the calculation of the unknown boundary surface normal displacements. The structural object is a tuning fork with 128.4 Hz resonant. The boundary element is a quadratic hexahedral element (eight nodes per element).

• 한국광학회지
• /
• 제14권1호
• /
• pp.80-84
• /
• 2003

두 가지의 다른 방법으로 광섬유를 직접 구동하여 공초점 현미경을 제작하였다. 압전소자와 튜닝 포크는 광섬유를 진동시키는데 사용하였다. 6 frame의 640$\times$480 픽셀 영상을 압전소자 진동으로 1초 동안 얻었고, 1 frame의 640$\times$480 픽셀 영상을 튜닝 포크 진동으로 1초 동안 얻었다 이러한 광섬유의 진동은 confocal 영상에 일그러짐을 주지 않았다.

• 전기학회논문지
• /
• 제58권12호
• /
• pp.2416-2419
• /
• 2009

We performed frequency response measurements of four tuning fork crystal oscillators with different sizes and analyzed their measured electrical equivalent circuit parameters of R, L, $C_S$, and $C_P$ as functions of the linear dimensions, length, width, and thickness. We observed that R and L showed an decreasing behavior with increasing length while $C_S$, and $C_P$ showed an increasing behavior. Similar dependences of the electrical parameters on thickness were also observed. On the contrary, any noticeable dependence of these parameters on width has not been found.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.559-559
• /
• 2012

We developed a new scheme for the highly sensitive near-field scanning optical microscope (NSOM) by using a dithering sample stage rather than a dithering probe. In the proposed scheme, the sample is directly loaded on one prong surface of a dithering bare tuning fork. Gap control between probe and sample is performed by detecting the shear force between an immobile fiber probe and the dithering sample. In a conventional NSOM, the Q factor drastically decreases from 7783 to 1000 or even to 100 by attaching a probe to the tuning fork. In our proposed NSOM, on the contrary, the Q factor does not change significantly, 7783 to 7480, when the sample is loaded directly to the tuning fork instead of attaching a probe. Consequently, the graphene sheets that cannot be observed by a conventional NSOM were clearly observed by the proposed method with sub-nanometer vertical resolution due to the extremely high Q factor.

• 비파괴검사학회지
• /
• 제27권4호
• /
• pp.345-353
• /
• 2007

근접장 마이크로파 현미경을 이용하여 수중에서 시료의 표면이미지에 대한 비파괴적 측정에 관한 연구를 하였다. 이때 근접장 마이크로파 현미경은 3.5-5.5 GHz에서 작동되었다. 본 연구에서는 수중에서 시료의 표면특성을 손상 없이 측정하기 위해 강성힘을 이용한 튜닝폭(tuning fork) 거리조절 시스템으로 팁과 시료 사이의 거리를 10 nm로 유지하였다. 더불어, 공기 및 수중에서 튜닝폭의 진동진폭의 변화와 공진주파수의 변화를 측정하여 수중에서 튜닝폭리 반응특성을 저하시키는 원인에 대해 알아보았다. 물 속에 시료가 충분히 잠기고, 동시에 물의 영향을 최소화하기 위해 팁의 길이를 2 mm로 제작하여 튜닝폭의 한 쪽면에 붙였다. 또한 측정과정에서 나타나는 증발현상을 해소하기 위해 엑츄에이터를 이용하여 보충용 수조를 제작하였으며, 보다 정확한 수중측정을 위해 보정프로그램을 응용하였다. 이를 통해, 시료의 공기 및 수중 측정의 가능성을 확인하기 위해 도체시료의 표면특성을 관측하고 비교하였다.