• 한국안전학회지
• /
• 제25권6호
• /
• pp.65-69
• /
• 2010

This paper presented an experimental study of slip resistance characteristics of shoes and floor surface contact with special focus on the effect of surface roughness, outsole material and mechanical abrasion. The factors that affected the results of slip resistances were investigated for four kinds of rubbers and five kinds of floor samples using the VIT(English XL) tribometer. The slip resistance was observed to increase gradually with increasing roughness for five kinds of floor roughness. In the higher surface roughness (larger than $11.5{\mu}m$), the slip resistance increased more rapidly and exceeded safety criteria at $22.60{\mu}m$. The slip resistance was observed to decrease with increasing hardness of outsole, except for butylenes rubber, which seemed to show the material property. The slip resistance decreased with number of trials. In the first several times(5 or 6 trial), the slip resistance decreased more rapidly, whereafter it approached gradually constant value. The slip resistance of surfaces has generally been shown to increase with floor surface roughness and to decrease with hardness of outsole and number of trials under the wet condition.

• 한국표면공학회지
• /
• 제34권2호
• /
• pp.125-134
• /
• 2001

($Ti_{1-x}$ $Cr_{x}$ )N coatings were deposited by an ion-plating method in a reactor with two separate metal sources, Ti and Cr. Ti was evaporated using an electron beam, while Cr evaporation was carried out by resistant heating. The Ti and Cr concentrations in the coatings were controlled by the Ti and Cr evaporation ratio. The coating hardness increased with increasing the Cr content(x) and showed a maximum value of 6,000 HK at around x=0.8. The critical load of the coatings, measured by the scratch test, was around 30 N. The wear resistance properties of the ($Ti_{1-x}$$Cr_{ x}$)N coatings were evaluated using a CSEM pin-on-disk type tribometer. A Cr-steel ball as well as a SiC ball, which had hardness values of 590 HK and 2,600 HK respectively, were used as the pin. After the wear test, the surface morphology, roughness and the concentration of the coatings were investigated, with the main focus being on the effect of wear debris and the transferred layer on the wear behavior.

• Tribology and Lubricants
• /
• 제30권6호
• /
• pp.364-369
• /
• 2014

To assess the wear behavior of rails against subway rail car wheels, we investigate the sliding wear behavior of pins derived from two types of rails (normal rails and heat-treated rails) against a disc derived from a subway rail car wheel, using a pin-on-disc-type tribometer. We base the sliding wear test conditions on the sliding conditions for wheel flange-rail gauge corner contact. We demonstrate the remarkable transition in the wear behavior of the pins derived from the rails, from severe wear to mild wear, as a function of the sliding distance. The wear rate of the heat-treated rail material in the running-in wear region is much lower than that of the normal rail material. Furthermore, the wear rates of the pins in the running-in wear region decrease with increasing hardness and with decreasing sliding speed. However, there is little difference between the heat-treated rail pin and the normal rail pin in the wear rate in the steady-state wear region. Stricter controls on the decarburized layer beneath the surface of rails are required to reduce the wear rate in the running-in wear region.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제45회 하계 정기학술대회 초록집
• /
• pp.169.2-169.2
• /
• 2013

본 연구에서는 gas를 이용한 PECVD 공법중 이온화 에너지가 높고 대면적 코팅이 용이한 Hybrid 코팅 장비에서 Linear Ion-Gun 이용하여 탄화수소 계열의 gas인 $C_2H_2$ 와 Si을 함유한 TMS (tetramethylsilane, $Si(CH_3)_4)$ gas를 이용하여 저마찰, 고경도 특성을 갖는 Si-DLC 코팅에 대한 연구를 수행하였다. Si-DLC 코팅에 앞서 전처리 공정으로 Linear Ion-Gun에 Ar gas를 주입하고 고전압의 DC 전원을 인가하여 제품 표면의 건식세정 및 표면 활성화를 진행 후, $C_2H_2$ 와 TMS gas를 Linear Ion-Gun에 주입하여 Si-DLC 코팅 공정을 진행하였다. Si-DLC 코팅시 $C_2H_2$ gas 주입량을 고정하고 TMS 가스 유량을 5~20sccm으로 조절하여 Si 함유량에 따른 Si-DLC 코팅막의 특성을 분석하였다. 이렇게 코팅된 Si-DLC의 박막 특성 분석으로 마찰계수 측정을 위해 ball-on-disk 타입의 tribometer를 사용하였으며, 박막 경도 측정은 Nano-indenter를 이용하여 분석을 진행하였다. 그 결과 Si을 포함하지 않는 DLC의 경우 마찰계수가 ~0.2를 가지는 반면, Si-DLC의 경우 Si 함유량이 약 1.5at%일 때, 마찰계수 ~0.04 저마찰의 우수한 특성을 지니며, 박막의 경도는 22[Gpa]로 고경도의 Si-DLC 코팅을 확인할 수 있었다.

• 대한기계학회논문집A
• /
• 제26권4호
• /
• pp.677-682
• /
• 2002

Break-in is an intentional treatment to enhance the performance life of machinery parts and to maintain static friction behavior. Most studies on break-in have concerned only about surface conditions such as roughness or film formation. But the exact mechanism of break-in has not been found yet. Friction, scuffing behavior and wear of AISI 1045 were studied in relation to break-in and residual stress. The cylinder-on-disk type tribometer was used with the line-contact geometry. Scuffing tests were carried out using a constant load of 730N. In the break-in procedure the step load was applied from 100N to 200N. In this experiment, it was found that the break-in helps compressive residual stress to be formed well enough to enhance the scuffing life during the scuffing test. Specimens that had high compressive residual stress induced by shot-peening show better wear resistance than those were not shot-peened. Results of scuffing test, break-in procedure and wear amount in relation to residual stress have been discussed.

• 대한금속재료학회지
• /
• 제50권8호
• /
• pp.549-556
• /
• 2012

The tribological behavior of CrMoN films with respect to surface chemistry was investigated by using X-ray photoelectron spectroscopy (XPS). All of the films were prepared from a hybrid PVD system consisting of DC unbalanced magnetron (UBM) sputtering and arc ion plating (AIP) sources. The tribological property of the films was evaluated by a friction coefficient using a Ball-on-disk type tribometer. The chemistry of wear track was analyzed by energy dispersive spectroscopy (EDS) and XPS. The friction coefficient was measured to be 0.4 for the CrMoN film, which is lower than that of a monolithic CrN film. EDS and XPS results imply the formation of an oxide layer on the coating surface, which was identified as molybdenum oxide phases, known to be a solid lubricant during the wear test.

• Tribology and Lubricants
• /
• 제36권6호
• /
• pp.342-349
• /
• 2020

The rapidly increasing threats to the environmental has increased the demand for biodegradable lubricants. Vegetable oils, such as olive, coconut, and sunflower oils, are readily obtainable and are not harmful, unlike synthetic and mineral oils. The tribological characteristics of these oils should be adequately examined for industrial applications. In this study, the lubrication characteristics of olive oil is investigated using a pin-on-disk-type tribometer under 500 gf of normal force, and the examination results are compared and analyzed with those of commercial synthetic lubricants for friction and wear. In addition, stearic acid, which is a type of saturated fatty acid, is mixed with olive oil as an additive to improve its lubrication characteristics. Olive oil with stearic acid additive is thus observed to exhibit the lowest friction coefficient for rotational speeds of 200 to 800 rpm. According to the wear analysis, a minimal amount of wear is observed when no additive is used. Hence, olive oil is able to effectively reduce friction and wear at relatively low speeds. These low friction and wear characteristics of olive oil are attributed to its compatibility with the substrate.

• Advances in concrete construction
• /
• 제11권3호
• /
• pp.231-238
• /
• 2021

The present work aims at investigating the effects of using various fine mineral additions as partial replacement to Portland cement on the tribological properties of concrete. To achieve this goal, concrete mixtures were prepared with different percentages (10, 20 and 30%) of limestone fillers (LF) and natural pozzolana (NP), and (20, 40 and 60%) of blast furnace slag (BFS). The interface yield stress (τ0) and viscous constants (η) that allow characterizing friction at the concrete-pipe wall interface were determined using a rotational tribometer. In addition, the compositions of the boundary layers that formed in the pumping pipes of the different concretes under study were also identified and analyzed. The experimental results obtained showed that the concretes studied have a linear tribological behavior that can be described by the Bingham model. Furthermore, the use of different mineral additions, especially limestone fillers and blast furnace slags, even at high rates, had a beneficial effect on the optimization of the volume of paste present in the boundary layer, which made it possible to significantly reduce the viscous constant of concrete. However, a maximum rate of 10% of natural pozzolana was recommended to achieve tribological properties that are favorable to the pumpability of concrete.

• Tribology and Lubricants
• /
• 제38권6호
• /
• pp.261-266
• /
• 2022

Notably, laser surface patterning facilitates tribological applications under lubricated sliding contacts. Consequently, a special pattern that can reduce the coefficient of friction under contact is considered necessary for improved machine efficiency. However, inappropriate pattern designs produce higher friction coefficients and cannot reduce friction. In this study, we use cast iron pins as specimens to investigate their friction and wear characteristics. Moreover, we experimentally investigate the correlation between the friction reduction effect and the design of groove crosshatch patterns fabricated with various angles and widths. We conduct a friction test using a pin-on-disc type tribometer under grease lubrication to study the friction reduction effect of the specimens, and we observe that the average coefficient of friction changes with the crosshatch angle and width. The experiment reveals that grooved crosshatch specimens with a crosshatch angle of 135°maximize friction reduction. The coefficient of friction of the groove specimens with a width of 120 ㎛ is lower than that of the specimens with a width of 200?. The friction reduction effect of the width of the groove is attributed to the density of the groove pattern. Thus, grooved crosshatch patterns can be designed to maximize friction reduction, and the friction property of a grooved crosshatch pattern is found to be related to its width and angle.

• Tribology and Lubricants
• /
• 제39권2호
• /
• pp.43-48
• /
• 2023

In this study, we investigate the tribological behavior of AISI 304 stainless steel pairs under deionized water and hexagonal boron nitride (h-BN) water dispersion lubrication. The specimen friction and wear properties are evaluated using a reciprocating ball-on-flat tribometer. The coefficient of friction remains nearly constant throughout the test under both lubricant conditions. The wear depth of the specimens under h-BN lubrication is smaller than that under deionized water lubrication, indicating the inhibition behavior of h-BN nanolubricants on direct metal-metal contacts. Optical micrographs and stylus profilometer measurements are performed to evaluate the severity of damage caused by the sliding motion and to determine the wear morphology of the specimens, respectively. The results show that h-BN nanolubricants does not have a significant effect on the friction behavior but demonstrates reduced wear owing to their trapping effect between the sliding interfaces. Moreover, scanning electron microscopy and energy-dispersive X-ray spectroscopy images of the specimens were acquired to confirm the trapping effect of h-BN between the sliding interfaces. The results also suggest that the trapped lubricants can distribute the contact pressure, reducing the wear damage caused by the metal-metal contact at the interface. In conclusion, h-BN nanolubricants have potential as an anti-wear additive for lubrication applications. Further investigation is needed to provide direct evidence of the trapping effect of h-BN nanoparticles between the sliding interfaces. These findings could lead to the development of more efficient and effective lubricants for various industrial applications.