• Journal of the Korean Ceramic Society
• /
• v.38 no.10
• /
• pp.928-935
• /
• 2001

In this study, two kinds of activated carbon fibers were prepared from PAN-based stabilized fibers by physical activation with steam. The variations in specific surface area, amount of iodine adsorption and pore size distribution of the activated carbon fibers after the activation process were discussed. The activated carbon fibers were prepared by two different methods, namely a 1- and 2-step method. For the 2-step method, carbonization of fibers in $N_2$ atmosphere was carried out to make carbon fibers and then activated by steam. In normal two step steam activation, BET surface area of about $1019m^2/g$ was obtained in the study. In the 1-step steam activation process, the carbonization and activation were simultaneously carried out. In the one step steam activation, BET surface area of $1635m^2/g$ was obtained after heat-treatment at $990^{\circ}C$. However, nitrogen adsorption isotherms for oxidized PAN based activated carbon fibers that were prepared by both methods were type I in the Brunauer-Deming-Deming-Teller (BDDT) classification even though they have different BET surface areas, amounts of iodine adsorption and pore size distributions.

• Journal of Ginseng Research
• /
• v.38 no.1
• /
• pp.1-7
• /
• 2014

Background: Although ginsenosides such as Rg1, Rb1 and Rg3 have shown promise as potential nutraceuticals for cognitive impairment, their use has been limited due to high production cost and low potency. In particular, the process of extracting pure Rg3 from ginseng is laborious and expensive. Methods: We described the methods in preparing ginseol k-g3, an Rg3-enriched fraction, and evaluated its effects on scopolamine-induced memory impairment in mice. Results: Ginseol k-g3 (25-200 mg/kg) significantly reversed scopolamine-induced cognitive impairment in the passive avoidance, but not in Y-maze testing. Ginseol k-g3 (50 and 200 mg/kg) improved escape latency in training trials and increased swimming times within the target zone of the Morris water maze. The effect of ginseol k-g3 on the water maze task was more potent than that of Rg3 or Red ginseng. Acute or subchronic (6 d) treatment of ginseol k-g3 did not alter normal locomotor activity of mice in an open field. Ginseol k-g3 did not inhibit acetylcholinesterase activity, unlike donezepil, an acetylcholinesterase inhibitor. Rg3 enrichment through the ginseol k-g3 fraction enhanced the efficacy of Rg3 in scopolamine-induced memory impairment in mice as demonstrated in the Morris water maze task. Conclusion: The effects of ginseol k-g3 in ameliorating scopolamine-induced memory impairment in the passive avoidance and Morris water maze tests indicate its specific influence on reference or long-term memory. The mechanism underlying the reversal of scopolamine-induced amnesia by ginseol k-g3 is not yet known, but is not related to anticholinesterase-like activity.

• Journal of Life Science
• /
• v.23 no.7
• /
• pp.879-885
• /
• 2013

Baby powder is an astringent powder used to prevent diaper rash. It also has other cosmetic uses. In general, it is composed of talc powder (talcum powder). Talc powder is harmful if inhaled because it can cause significant lung damage. With the aim of developing a new rice-based baby powder, three kinds of rice varieties were selected and pulverized. To determine the cost-effectiveness of the different states of rice powder, several milling processes were tried, and the powder characteristics of the resulting rice powder, such as particle size, biological activities, digitalized color value, and moisture content before and after coating treatment with essential oil and silicon oil, were examined. "Goami" showed good flour characteristics with respect to lightness (92.0, $L^*$[D65] value) and particle size ($8.9{\mu}m$). SEM analysis showed that the rice powder particles coated in the essential oil and silicon oil showed a smoother and rounder appearance than those of the talc powder. In addition, the average particle size was decreased by the essential oil and silicon oil coating. The silicon oil coating solved the problem of moisture absorption in rice flour. Rice flour properly coated with essential oil and silicon oil shows great potential as a new material source of powder.

• Quality Improvement in Health Care
• /
• v.9 no.2
• /
• pp.210-228
• /
• 2002

Background: The purpose of this research was to examine the fall incidence rate and its related factors of fall in inpatients. Methods: The data were collected from the 138 fall incident reports in one tertiary hospital in Seoul from April 1st 1999 to September 30th 2001. The Fall Incident Report Form was originally developed based on that of Massachusetts General Hospital revised in 1995. And this was modified for this survey by the collaborating work of QI team including researcher and department of nursing service of this particular hospital. The contents of Fall Incident Form were general characteristics of patient. factors related to fall. types and places of fall. circumstances, nursing interventions. and outcome. Results: 1) The incidence rate of fall was 0.08% of total discharged patients and 0.081 per 1000 patient-day. This incidence rate is much lower than that of several hospitals in USA. This finding might result from the different incidence report system of each hospital. 2) The characteristics of fall-prone patient were found as follows. They were mostly over 60 years old, in alert mental status, ambulatory with some assistance, and dependent on ambulatory device. The types of diseases related high incidence rate were cerebrovascular disease(3.2), hypertension(1.6), cardiovascular disease(1.4), diabetes(1.3) and liver disease(0.6). 3) The majority of fall events usually occurred m bed. bedside(walking or standing) and bathroom in patient room. Usually they were up on their own when they fell. And there were more falls of elderly occurred during night time than day or evening. 4) 63.8% of fall events resulted in physical injuries such as fracture and usually the patients had diagnostic procedures and some treatment(ex. suture) which caused additional cost to the patients and their families. 5) The found risk factors of fall were drugs(antihypertensive drug, diuretics) and environmental factors like too high bed height, long distance of bedside table and lamp switch, and slippery tile of bathroom floor. Conclusion: Considering these results, every medical and nursing staff should be aware of the risk factors of patients in hospital, and should intervene more actively the preventive managements, specially for the elderly patients during night. Therefore, it is recommended that the development of Fall Prevention Programs based on these results.

• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.5
• /
• pp.527-534
• /
• 2006

The purpose of this study is the development of more effective filter-type polymer adsorbent for removal of anionic pollutants from wastewater. In order to synthesize the polymer adsorbent that possesses anionic exchangeable function, carboxyl(-COOH) group of PP-g-AA nonwoven fabric was converted into amine($-NH_2$) group by the chemical modification using diethylene triamine(DETA). FT-IR data indicate that amine group was introduced into PP-g-AA through amidation of grafted acrylic acid by reaction with DETA. The degree of amination increased with increase in the reaction time and temperature of the chemical modification process, and was significantly improved by the pre-swelling treatment of PP-g-AA with solvent and addition of metal chlorides as a catalyst in following order as $NH_4OH>MeOH{\geq}HCl{\geq}H_2O\;and\;AlCl_3>FeCl_3{\geq}SnCl_2{\gg}ZnCl_2{\geq}FeCl_2$, respectively. However, the addition of catalyst limited the reusability of DETA, hence was less useful from the viewpoint of cost effectiveness and waste management. The anion exchange capacity of the aminated PP-g-AA(PP-g-AA-Am) increased with increase in the degree of amination, but it reached maximum value at the degree of amination as about $50{\sim}60%$. The anion exchange capacity of PP-g-AA-Am was higher than those of commercial anion resins.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.2
• /
• pp.177-183
• /
• 2005

The effluent quality is directly affected by the separation of biological solids in a final clarifier because the majority of discharged $BOD_5$ and SS are virtually dependent on the results of biological solids in the sedimentation tank effluent. If a final clarifier is effectively designed and operated, the desired goal of clarification for wastewater can be achieved together with the cost reduction in the treatment of wastewater. To this end flow characteristics and the removal efficiency of SS are numerically investigated especially by the change of the inlet position and the installation of baffle to improve the performance of a rectangular final clarifier. The 2-D computer program developed in a rectangular coordinates has been successfully validated against experimental residence time distribution(RTD) curves obtained by tracing radio-isotope. The lowering of the inlet position weakens the density current and induces the settling of SS in the front zone of a clarifier. Thus the decreased traveling distance of the sludge increases the removal efficiency of SS in the effluent. The inlet baffle installed in the front region of clarifier prevents the short circuiting flow and induces to flow into the dense underflow, which eventually improves the effluent quality. In the case of lower inlet position, however, installation of baffle results in degradation of effluent quality. Consequently it is strongly recommended that in-depth numerical study be performed in advance for optimizing a clarifier design and retrofitting to improve effluent quality in a final clarifier.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.16 no.3
• /
• pp.23-30
• /
• 2012

For cracked concrete, it is obvious that cracks should be preferential channel for the penetration of aggressive substances such as chloride ions according to the previous researches. In order to extend the lifetime of cracked concrete, critical issues in the performance of the concrete is the risk of chloride-induced corrosion. Even though crack width can be reduced due to the high reinforcement ratio, the question is to which extend these cracks may jeopardize the durability of cracked concrete. If the size of crack is small, surface treatment system can be considered as one of the best options to extend the service life of concrete structures exposed to marine environment simply in terms of cost effectiveness versus durability performance. Thus, it should be decided to undertake an experimental study on the effect of surface coating system, which can be able to seal the concrete and the cracks to aggressive substances-induced corrosion in particular. In this study, it is excuted to examine the effect of surfaced treated systems on chloride penetration and carbonation through compressive stress induced cracks. Experimental results have showed conclusively that critical stress linked with deterioration, should be existed in compressive stress ratio 50 ~ 70% for chloride penetration and 70 ~ 80% for carbonation, respectively. When the critical stress is exceeded in concrete, a comparatively large deterioration was measured where the critical stress in concrete, the increase in the mass transportation is marginal in spite of the large increase in micro-cracks. As for the effect of surface coating system on crack-sealing, it can be seen conclusively that cracks can be healed.

• Research in Community and Public Health Nursing
• /
• v.7 no.1
• /
• pp.138-153
• /
• 1996

Intending to offer basic information for a prospective health services in Korea, this study is to investigate the complication caused by sterilization in goverment family planning program from 1962 to 1995. The results are as follows: 1. Total number of sterilization performed during the period from 1962 to 1995 were 1.367,772 cases of male sterilization and 2,889,635 cases of female sterilization. 2. Incidence of the complication caused by sterilization operation from 1980 to 1995 were 1,883(0.20%) out of 925,801 cases in vasectomies and 15,866(0.70%) out of 2,256,020 cases in tubal sterilizations. 3. Major complications in vasectomy were epididymities of 658 cases (34.9%), vas recanalization of 326 cases(17.3%), hematoma of 266 cases(14.1%), scrotal abscess of 184 cases(9.8%), sperm granuloma of 76 cases(4.0%),and other of 373 cases(19.8%). On the other hand, in tubal sterilization, ectopic pregnancy was the most significant complication of 15,078 cases (95.0%) among 15,866 total complications, followed by pelvic inflammatory diseases of 155 cases(0.9%), peritonities of 96 cases(0.6%), ovarian & tubal bleeding of 31 cases(0.2%), intestinal perforation of 16 cases (0.1%), uterine bleeding of 14 cases(0.1%), uterine cervix laceration of 1 case (0.1%), and other of 271 cases(1.7%), while 161 pregnancies(0.1%) were terminated and 43 cases(0.3%) with normal delivery. 4. The occurrence rate of the complication for each period showed that most of the complication cases by vasectomy occurred in a year after the operation -the cases were 1,256 (66.7%). 254 cases(13.5%) occurred between the next year and the 2nd year, 138 cases (7.3%) between the 2nd year and the 3rd year, 73 cases(3.9%) between the 3rd year and the 4th year, 52 cases(2.8%) between the 4th year and the 5th year, 31 cases(1.6%) between the 5th year and the 6th year, 79 cases(4.2%) over the 6th year. Tubal sterilization indicated that the occurred complication cases in a year were 2,175 cases(13.7%), 2,113 cases(13.3%) occurred between the next year and the 2nd year, 2,082 cases(13.1%) between the 2nd year and the 3rd year, 2,049 cases (12. 9%) between the 3rd year and the 4th year, 1,819 cases(11.5%) between the 4th year and the 5th year, 621 cases(10.2%) between the 5th year and the 6th year, 4,007 cases(25.3%) over the 6th year. 5. For the cost of complication treatment, total \7,928,229,000 were paid as medical expenditure in which \609,438,000 for vasectomy and \7,318,791,000 for tubal sterilization. Accordingly per capita expenses were \345,000 for vasectomy and \467,000 for tubal sterilization. As the proportion of government sterilization program was decreased after 1988, that of private sterilization program would be increased. So it is recommended to set a guideline for the private sterilization program and to continue government sterilization program for the lower class.

• Journal of Periodontal and Implant Science
• /
• v.38 no.2
• /
• pp.153-162
• /
• 2008

Purpose: Recombining bone morphogenetic protein (BMP) is usually acquiredfrom high level animals. Though this method is effective, its high cost limits its use. The purpose of this study was to evaluate the effect of bone morphogenetic protein-2 with protein transduction domain (BMP-2/PTD;TATBMP-2) on bone regeneration. Rat calvarial defect model and osteoblastic differentiation model using MC3T3 cell were used for the purpose of the study. Materials and Methods: MC3T3 cells were cultured until they reached a confluence stage. The cells were treated with 0, 0.1, 1, 10, 100, 500 ng/ml of BMP-2/PTD for 21 days and at the end of the treatment, osteoblastic differentiation was evaluated usingvon Kossa staining. An 8mm, calvarial, critical-size osteotomy defect was created in each of 48 male Spraque-Dawley rats (weight $250{\sim}300\;g$). Three groups of 16 animals each received either BMP-2/PTD (0.05mg/ml) in a collagen carrier, collagen only, or negative surgical control. And each group was divided into 2 and 8 weeks healing intervals. The groups were evaluated by histologic analysis(8 animals/group/healing intervals) Result: In osteoblastic differentiation evaluation test, a stimulatory effect of BMP-2/PTD was observed in 10ng/ml of BMP-2/PTD with no observation of dose-dependent manner. The BMP-2/PTD group showed enhanced local bone formation in the rat calvarial defect at 2 weeks. New bone was observed at the defect margin and central area of the defect. However, new bone formation was observed only in 50% of animals used for 2weeks. In addition, there was no new bone formation observed at 8 weeks. Conclusion: The results of the present study indicated that BMP-2/PTD(TATBMP-2) have an positive effect on the bone formation in vitro and in vivo. However, further study should be conducted for the reproducibility of the outcomes.

• Journal of Korean Society of Forest Science
• /
• v.89 no.3
• /
• pp.384-388
• /
• 2000

For the control of Corythucha ciliata, the insecticidal activity of five commercial pesticides (Monocrotophos 25%SL, Phosphamidon 50%SL, Imidacloprid 20%DC, Thiamethoxam 15%DC and Acetamiprid 20%SL) were examined with trunk injection method in Seoul, Sanbon and Chungju. The insecticidal activity of five commercial pesticides was >88%. The insecticidal activity of Monocrotophos maintained 31 days later after trunk injection when treated leaves were supplied to this pest. This result indicates that one application of trunk injection is enough to control this pest, and this method can save the control cost compared with ground application which should be applied two or three times per year to control this pest. To make the model of treatment dosage at each D.B.H class (cm), $1.0m{\ell}/DBH$, $1.5m{\ell}/DBH$ and $2.0m{\ell}/DBH$ pesticide dosage was used. At <20cm, the insecticidal activity of $1.0m{\ell}$ dosage was >95%, and $1.5-2.5m{\ell}$ dosage was needed for the effective control at 30~50cm. More than $2.5m{\ell}$ dosage was effective at >50cm. Spray method was used in laboratory to select pesticides for ground application. Three commercial pesticides (Ethofenprox 20%EC, Ethofenprox 10%WP and Cyfluthrin 1%EC) were used, and all pesticides showed >95% insecticidal activity.