• Journal of Information Display
• /
• v.2 no.1
• /
• pp.38-42
• /
• 2001

Thin films of $In_2O_3-SnO_2$(ITO), $SnO_2$, and $SiO_2$ were prepared on the PET substrate by DC magnetron roll sputtering. 135 nm thick ITO film on $SiO_2$/PET substrate has sheet resistance as low as 55 ${\Omega}/square$ and transmittance as high as 85%. $H_2O$gas permeation through the film was 0.35 g/$m^2$ in a day. These properties are enough on optical film for the plastic LCD substrate or touch panel. Both refractive index and sheet resistance of ITO was found to be very sensitive to $O_2$ flow rate. Oxygen flow conditions have been optimized from 4 to 5 SCCM at $10^{-3}$torr. It is also shown that both thickness of $SnO_2$ and refractive index of $SiO_2$ decrease as $O_2$ flow rate increases.

• Solar Energy
• /
• v.14 no.2
• /
• pp.29-37
• /
• 1994

Radiative charaacteristics of glass windows and porous absorbing media which can be used for a solar air heater are determined through the measurements of spectral transmittances. Those in the visible range are measured by the UV-IR spectrometer. Refractive index of glass are obtained by the comparison of the measured transmittances and the correlations derived from the electromagnetic theory and are compared to the theoretical ones calculated from the classical dispersion theory. Absorption and back-scattering coefficients of 15-mesh stainless wire screens are calcuated by the comparison of the measured transmittances and the correlations derived from the two flux model.

• Korean Journal of Materials Research
• /
• v.29 no.7
• /
• pp.399-407
• /
• 2019

This research is carried out to analyze the effects of Styrene and PVP on the properties of silicone hydrogel lenses. Styrene group and PVP(Polyvinylpyrrolidone) are used as additives for a basic combination containing silicone monomer, TSMA(trimethylsilyl methacrylate) and DMA(n,n-dimethylacrylamide) added to the mix at ratios of 1~10 %. Silicone hydrogel lens is produced by cast-mold method. The polymerized lens sample is hydrated in a 0.9 % saline solution for 24 hours before its optical and physical characteristics are measured. Measurement of the physical characteristics of the produced material shows that the refractive index is 1.3682~1.4321, water content 77.11~45.73 %, visible light transmittance 95.14~88.20 %, and tensile strength 0.0652~0.3113 kgf. The results show a decrease of refractive index as the ratio of additives and water content decreases. The result of the stabilization test of polymerization show an increase of extractables along with increase of the ratio of additives, but the difference is not significant for all samples, so it can be judged that the stabilization of the polymer is maintained. Therefore, the additions of styrene and PVP should be taken into consideration for their effects on the physical properties of silicone hydrogel lens.

• Journal of the Semiconductor & Display Technology
• /
• v.21 no.3
• /
• pp.39-44
• /
• 2022

The light extraction technology for improving the light efficiency of OLEDs is the core technology for extracting the light inside the OLEDs to the outside. This study demonstrates a simple method to generate random nanostructures (RNSs) containing high refractive index nanoparticles to improve light extraction and viewing angle characteristics. A simple dry low-temperature process makes the nanostructured scattering layer on the polymer resin widely used in the industry. The scattering layer has the shape of randomly distributed nanorods. To control optical properties, we focused on changing the shape and density of RNSs and adjusting the concentration of high refractive index nanoparticles. As a result, the film of the present invention exhibits a perpendicular transmittance of 85% at a wavelength of 550 nm. This film was used as a scattering layer to reduce substrate mode loss and improve EL efficiency in OLEDs.

• Journal of Integrative Natural Science
• /
• v.17 no.3
• /
• pp.67-73
• /
• 2024

Hydrophilic contact lens was prepared by dispersing MXene material in a hydrogel mixture, and the purpose of this study was to evaluate its properties as an ophthalmic material. The MXene used in the experiment was manufactured through an etching process using titanium aluminum carbide 312 [Ti3AlC2] and hydrofluoric acid [HF]. For the preparation of hydrophilic contact lenses, 2-hydroxyethyl methacrylate [HEMA], a photoinitiator 2-hydroxy-2-methylpropiophenone [2H2M], and a cross-linker Ethylene glycol dimethacrylate [EGDMA] were used, and UV-rays was irradiated for 50 seconds for photopolymerization. Optical transmittance, refractive index, water content, contact angle, electromagnetic wave shielding ability, and photo-thermal conversion effect were measured to evaluate the physical properties of the manufactured contact lens. Compared to MXene materials, MXene mixed with Dimethyl sulfoxide [DMSO] had superior dispersion ability in organic solvents, and the transparency of the prepared hydrophilic contact lenses was high. MXene did not significantly affect the refractive index and water content, and improved the wettability of the contact lens. In addition, the MXene material used as an additive showed electromagnetic wave shielding ability and photo-thermal conversion effect based on its excellent electrical conductivity. It is judged that the mixture using MXene as an additive can be used as a functional contact lens material for electromagnetic wave shielding and ocular photo-thermal therapy.

• Journal of Integrative Natural Science
• /
• v.9 no.4
• /
• pp.249-254
• /
• 2016

This study evaluated the physical and optical characteristics of hydrophilic ophthalmic polymer with addition of 2-methacryloyloxyethyl phosphorylcholine in the basic hydrogel ophthalmic lens material, and in particular, the utility of 2-methacryloyloxyethyl phosphorylcholine as an ophthalmic contact lens material for ophthalmologic devices was investigated. In this study 2-methacryloyloxyethyl phosphorylcholine were used as additives. For the preparation of hydrogel lens 2-hydroxyethyl methacrylate, methyl methacrylate, acrylic acid and a cross-linker EGDMA were copolymerized in the presence of AIBN as an initiator. The physical properties of the produced polymers were measured as followings. The refractive index of 1.433~1.393, water content of 35.95~53.16%, contact angle of $70.6{\sim}51.24^{\circ}$, UVB transmittance of 81.2~82.4%, UV-B transmittance of 81.2~82.4% and visible transmittance of 91.4~92.2% were obtained. Also, in case of protein absorption, the measurement showed that absorbance of Reference and MPC-10 sample was 0.2598 and 0.2250 respectively. Based on the results of this study, ophthalmic lens material containing 2-methacryloyloxyethyl phosphorylcholine is expected to be used usefully as a material for high wettability and inhibitor of protein adsorption for ophthalmic hydrogel lens.

• Journal of Integrative Natural Science
• /
• v.9 no.1
• /
• pp.16-22
• /
• 2016

The optical and physical and characteristics of hydrogel ophthalmic lens polymerized with addition of 2,6-difluoropyridine, SiPc(silicon 2,9,16,23-tetra-tert-butyl-29H31H-phthalocyanine dihydroxide) and nanodiamond in the basic hydrogel material were evaluated. In particular, the utility of 2,6-difluoropyridine, SiPc and nanodiamond as a hydrogel ophthalmic lens material was investigated. 2,6-difluoropyridine, SiPc and nanodiamond were used as additives. And also, 2-hydroxyethyl methacrylate, acrylic acid, methyl methacrylate and a cross-linker EGDMA were copolymerized in the presence of AIBN as an initiator. The refractive index of 1.4348~1.4361, water content of 33.30~34.02%, UV-B transmittance of 4.77~67.50%, UV-A transmittance of 1.45~89.19% and visible transmittance of 32.12~92.21% were obtained. The results of hydrogel lens containing 2,6-difluoropyridine (add 5%) showed antibiosis for staphylococcus aureus. The produced copolymer is suitable for hydrogel soft ophthalmic lenses with antibiotic and anti-UV effect.

• Journal of Adhesion and Interface
• /
• v.11 no.2
• /
• pp.50-56
• /
• 2010

Polyethyleneterephthalate (PET) film is widely used in various industrial fields such as mobile phone, display pannel, notebook etc. Recently PET film attached on indium tin oxide (ITO) surface has a role of high pencil hardness, high refractive index etc. So we synthesized two types of multi-functional monomer which are epoxy modifed acrylate and unmodified acrylate type using recyclable resource like phloroglucinol, derived from trinitrotoluene. We studied the effect of multi-functional monomer's chemical structure on the various properties such as refractive index, optical transmittance, and pencil hardness. We characterized synthesized multi-functional monomer by qualitative analysis through H NMR. We observed that pencil hardness of 1,3,5-triepoxide benzene and 1,3,5-triacrylate benzene they have the range of 2~3 H at high UV dosage of 300 mW. Refractive index appeared the value of 1.54~1.57. Transmittance of all multi-functional monomers has more than 93%.

• Journal of Korean Ophthalmic Optics Society
• /
• v.15 no.1
• /
• pp.55-60
• /
• 2010

Purpose: We investigated the changes of plastic lens after etching of coating films by comparing uncoated lens. Methods: CR-39, middle index and high index lenses of 0 (zero) diopter were etched at $80^{\circ}C$ and room temperature using a coating remover, and then changes of refractive power, transmittance and surface morphology were investigated. Results: There were no differences in refractive power and transmittance between uncoated and etched lenses. The etching rate was similar in both CR-39 and middle index lens, but in the case of high index lens, it was slower and less steady than the others. From the SEM observation of lens surface, etching damage was found out on the surface of etched lens. It was shown the least damage in middle index lens but the most damage in high index lens. Conclusions: If the etching of coating films is demanded on condition that the surface of ophthalmic lenses are not damaged, a using of most adequate coating remover based on lens material should be considered, and a caution for proper etching conditions is required.

• Current Photovoltaic Research
• /
• v.8 no.1
• /
• pp.1-5
• /
• 2020

The most important factor in enhancing the performance of an optical device is to minimize reflection and increasing transmittance of light for a broad wavelength range. The choice of appropriate coating material is crucial in decreasing reflection losses at the substrate. The purpose of this review is to highlight anti-reflection coating (ARC) materials that can be applied to silicon solar cell and glass substrate for minimizing reflection losses. The optical and electrical behavior of ARC on a substrate is highly dependent on thickness and refractive index (RI) of ARC films that are being deposited on it. The coating techniques and performance of single and multi-layered ARC films after coated on a substrate in a wide range of wavelength spectrum will be studied in the paper.