• Geomechanics and Engineering
• /
• 제35권4호
• /
• pp.437-447
• /
• 2023

The failures of tailing dams have caused irreparable damage to human lives, assets and environment and this has ultimately resulted in great economic, social and environmental challenges worldwide. Due to this, investigation into mechanical behaviour of tailings has received some attention. However, the knowledge and understanding of mechanics of behaviour in iron tailings is still limited. This study investigates the mechanics of iron tailings from Nigeria considering grading, effects of fabric resulting from different sample preparations and the possibility of non-convergent behaviour. This was achieved by conducting series of one-dimensional compression tests in conjunction with index, microstructural, chemical and mineralogical tests. The materials are predominantly poorly graded, non-clayey and non-plastic. The tailings are characterised by angular particles with no obvious particle aggregations and dominated by silicon, iron, aluminium, haematite and quartz. The compression paths do not converge and unique normal compression lines are not found and this is an important feature of the transitional mode of behaviour. The behaviour of these iron tailings therefore depends on initial specific volume. The preparation methods also have effect on the compression paths of the samples. The gradings of the samples have an influence on the degree of transitional behaviour but the preparation methods do affect the degree of convergence. The transitional mode of behaviour in these iron tailings investigated is very strong.

• Structural Engineering and Mechanics
• /
• 제11권3호
• /
• pp.287-299
• /
• 2001

Columns in multi-storey frames are presently categorised as either braced or unbraced, usually by means of the stability index criterion, for estimating their effective length ratios by design aids such as 'alignment charts'. This procedure, however, ignores the transition in buckling behaviour between the braced condition and the unbraced one. Hence, this results in either an overestimation or an underestimation of effective length estimates of columns in frames that are in fact 'partially braced'. It is shown in this paper that the transitional behaviour is gradual, and can be approximately modelled by means of a 'fuzzy logic' based technique. The proposed technique is simple and intuitively agreeable. It fills the existing gap between the braced and unbraced conditions in present codal provisions.

• Wind and Structures
• /
• 제10권6호
• /
• pp.511-532
• /
• 2007

The present study aims to generate turbulent inflow data to more accurately represent the turbulent flow around a square cylinder when the inflow turbulence level is significant. The modified random flow generation (RFG) technique in conjunction with a previously developed LES code is successfully adopted into a finite element based fluid flow solver to generate the required inflow turbulence boundary conditions for the three-dimensional (3-D) LES computations of transitional turbulent flow around a square cylinder at Reynolds number of 22,000. The near wall region is modelled without using wall approximate conditions and a wall damping coefficient is introduced into the calculation of sub-grid length scale in the boundary layer of the cylinder wall. The numerical results obtained from simulations are compared with each other and with the experimental data for different inflow turbulence boundary conditions in order to discuss the issues such as the synthetic inflow turbulence effects on the 3-D transitional flow behaviour in the near wake and the free shear layer, the basic mechanism by which stream turbulence interacts with the mean flow over the cylinder body and the prediction of integral flow parameters. The comparison among the LES results with and without inflow turbulence and the experimental data emphasizes that the turbulent inflow data generated by the present RFG technique for the LES computation can be a viable approach in accurately predicting the effects of inflow turbulence on the near wake turbulent flow characteristics around a bluff body.

• Geomechanics and Engineering
• /
• 제12권1호
• /
• pp.127-138
• /
• 2017

A series of high-pressure isotropic compression tests were performed on four types of poorly graded silica sand that were artificially prepared based on representative grading curves and similar mineralogy composition of seabed sediment containing different fines contents existing in the Nankai Trough. The addition of fines steepens the initial compression path and increases the decrement of the void ratio after loading. The transitional behaviour of the poorly graded sand with a larger amount of fines content was identified. The slope of the normal compression line shows a slight decreasing tendency with the level of fines content. The bulk modulus of silica sand with fines was lower when compared with the published results of silica sand without fines. A small amount of particle crushing of the four types of poorly graded sand with variable fines content levels was noticed, and the results indicated that the degree of particle crushing tended to decrease as the fines content increased.

• 한국지반공학회논문집
• /
• 제28권7호
• /
• pp.31-40
• /
• 2012

토질분류법에서 흙은 크게 사질토와 점성토로 분류되며, 실제 설계에서도 이와 같이 분류된 흙 종류에 따라 다른 예측식을 사용하여 흙의 거동을 평가하고 있다. 그러나, 모래-세립분 혼합토는 전형적으로 중간토(intermediate soil or transitional soil)로 구분되어 모래와 점토의 중간적인 성질을 나타내기 때문에, 이러한 혼합토에 대한 거동특성을 평가할 수 있는 기준이 필요하다. 본 논문에서는 입도분포를 조정한 특정 모래에 세 가지 종류의 세립분으로 구성된 다양한 세립분함유율을 갖는 시료를 대상으로 일련의 반복 삼축압축시험을 수행하였다. 모래가 골격을 이루는 간극비(골격간극비)를 고려하여, Silica sand와 세립분(Iwakuni natural clay, Tottori silt, kaolinite)을 다양한 건조 중량비로 혼합하여 그 특성을 파악하였으며, 실험결과로 전환 세립분함유율(threshold fines content)을 넘지 않는 혼합토의 반복전단강도를 세립분 함유율 증가에 따라 평가하였다. 그 결과, 반복 전단응력비는 세립분 함유율 증가에 따라 조밀한 시료에서는 감소, 느슨한 시료에서는 증가하는 결과를 나타냈으며, 혼합토의 반복전단응력비를 등가골격간극비의 개념을 이용하여 평가했다.

• 한국식물학회:학술대회논문집
• /
• 한국식물학회 1987년도 식물생명공학 심포지움 논문집 Proceedings of Symposia on Plant Biotechnology
• /
• pp.191-211
• /
• 1987

Common usage of the concept of juvenility implies that there is one physiological phase, the juvenile phase, which manifests itself in the various morphological and physiological phenomena observed in juvenile higher plants. The juvenile phase is often defined as that time from seed germination until the plant attains the ability to flower regulating such behaviour. This definition precludes plants from flowering in the juvenile phase. It is of major interest, therefore, to identify the physiological controls(Bluehreife) regulating such behavior. The length of the juvenile period in higher plants ranges from one year to over 60 years in different species. The long juvenile period of seedling is the main cause of the long duration of the breeding process. I determined the length of the juvenile period in various plants and its control of phase changes in natural system in relation to factors such as plant size and age, shoot morphology, apex size, root system and phytohormonal and nutritional status is reviewed. From the own experimental and observational evidence available it appears that both hormonal and nutritional factors can be involved in control of juvenility but that a specific juvenile or flowering hormone is not involved. Grafting, ringing, scoring, root pruning and fertilization have been used to accelerate flowering, but in most cases these cultured treatments are only successful on plants that were passed the juvenile phase. It is suggested that there are intrinsic difference between the meristematic cells of the apieces of juvenile and adult shoot, which are thus determined with respect to there development potentialities. The problems associated with the maintenance of the determined state through mitosis are discussed. The properties of transitional forms of Ribes nigrum L. intermediate between the juvenile and adult phase, are descrived and there implications discussed. Analogies are drawn between juvenile phenomena in woody perennials and in herbaceous species.