• 전력전자학회논문지
• /
• 제18권2호
• /
• pp.123-130
• /
• 2013

This paper proposes the switched trans Z-source inverter(STZSI) which combined the characteristics of the trans Z-source inverter(TZSI) and the switched inductor Z-source inverter(SLZSI). The proposed STZSI has the same performance compared with the SLZSI which is improved the voltage boost performance of the conventional typical X-shaped ZSI, and it has advantage that circuit structure of Z-impedance network is more simple. And, in order to step up the voltage boost factor under the condition of the same duty ratio, unlike the SLZSI adding the inductors and diodes, the proposed method is dune by changing the turn ratio of trans primary winding of Z-impedance network. To confirm the validity of the proposed method, PSIM simulation and a DSP(TMS320F28335) based experiment were performed using trans with turn ratio 1 and 2 under the condition of the input DC voltage VI=50V, duty ratio D=0.1 and D=0.15. As a result, under the same input/ouput condition, the inverter arm voltage stress of the proposed method is reduced to about 15%-22% as compared with typical X-shaped ZSI, and the elements in Z-impedance network of the proposed method is reduced as compared with the SLZSI.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1998년도 Proceedings ICPE 98 1998 International Conference on Power Electronics
• /
• pp.701-708
• /
• 1998

This paper presents a novel non-resonant PWM DC-DC converter for X-ray high-voltage power generator using the parasitic impedances of the high-voltage high-frequency link transformer with its output high-voltage control scheme and steady-state characteristics compared to the conventional series-parallel resonant DC-DC converter. The key point of this approach is to evaluate effectiveness of reduction of the turn ratio of the high-voltage high-frequency transformer on improvements in power conversion efficiency and the power factor applying a boost AC-DC converter as DC voltage source, especially in the long exposure term and light output load ranges.

• 한국전자파학회논문지
• /
• 제11권4호
• /
• pp.610-618
• /
• 2000

본 논문은 T-모양 급전션을 갖는 마이크로스트립 슬롯 안테나를 전송선로 모델로 해석을 하였다. 마이크로스 트립 선로와 슬롯 선로의 접합변을 트랜스포머로 모델링을 하였으며 실험적인 방법으로 트랜스포머의 turn ratio 를 유도하였다. 전송선로 모델을 이용하여 단일 안테나뿐만 아니라 $1\times2,l\times4$ 배열 안테나를 해석하여 설계하 였고 제착하여 전송선로 모델로 계산한 반사손실 값과 측정값의 비교를 통해 전송선로 모텔이 안테나 설계에 유 용함을 입증하였다. 측정한 단일 안테나, $1\times2,l\times4$배열 안테나의 대역폭은 VSWR $\leq2$를 기준으로 하여 각각 2 28.5%, 47.8% 50.9% 였고 $1\times4$배열 안테나의 E-명변에서 주빔의 3dB 빔폭은 약$27^{\circ}$ 이득은 7.97 dBi 였다.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2006년도 전력전자학술대회 논문집
• /
• pp.403-405
• /
• 2006

Over the years, plasma display panel (PDP) manufacturers have impressed the flat panel display industry with yet another new product essentially having the merits of a larger screen size. Since larger size implies higher power ratings, voltage/current ratings of the power devices used have become a rising concern. Another important concern is the brightness of PDP, one way of increasing which is by operating the PDP at higher frequencies. In order to address the above issues, a transformer coupled sustain-driver for AC-PDP is proposed During the transition time, the two windings of the transformer greatly boost up the displacement current flowing through the panel capacitance and hence enable a fast inversion of the voltage polarity with practical values of resonant inductance. In the proposed topology, the resonant inductance can be increased by a factor of $(n+1)^2$ as compared to prior approaches. Increased inductance results in lower current stresses. Moreover, high frequency operation is possible by using higher value of n (turn ratio of the transformer). The operational principle and design procedure of the proposed circuit are presented with theoretical analysis. The validity of the proposed sustain driver is established through simulation and experimental results using a 42-in PDP

• 한국조명전기설비학회지:조명전기설비
• /
• 제11권6호
• /
• pp.90-95
• /
• 1997

고주파 유도가열을 위한 인버터의 공진회로 설계에서 인덕턴스 L의 작용과, 출력전달 요소로 사용된 변압기의 결합계수, 그리고 코일을 사용한 가열부하의 결합계수가 공진회로의 출력, 회로의 Q와 공진주파수에 큰 영향을 주고 있음을 등가회로를 도출하여 그 특성을 해석하였다. 또한 변압기를 테브난 등가회로로 구성할 경우, 변압기의 이차측 임피던스를 일차측 임피던스고 환산하면, 권선비 n$^2$에 비례 할 뿐만 아니라 결합계수 $K^2$에도 비례함을 도출하여 결합계수형 테브난 등가회로에 의한 정확성이 큰 인버터 공진회로 설계의 기초방식을 나타냈다.

• 한국산업융합학회 논문집
• /
• 제20권2호
• /
• pp.115-124
• /
• 2017

This paper aims to develop an SMPS topology for handling a high range of input voltages based on a DC-DC flyback converter circuit. For this purpose, 2 capacitors of the same specifications were serially connected on the input terminal side, with a flyback converter of the same circuit configuration serially connected to each of them, so as to achieve high input voltage and an effect of dividing input voltage. The serially connected flyback converters have the transformer turn ratio of 1:1, so that each coil is used for the winding of a single transformer, which is a characteristic of doubly-fed configuration and enables the correction of input capacitor voltage imbalance. In addition, a pulse transformer was designed and fabricated in a way that can achieve the isolation and noise robustness of the PWM output signal of the PWM controller that applies gate voltage to individual flyback converter switches. PSIM simulation was carried out to verify such a structure and confirm its feasibility, and a 100W class stack was fabricated and used to verify the feasibility of the proposed high voltage SMPS topology.

• 조명전기설비학회논문지
• /
• 제30권3호
• /
• pp.65-72
• /
• 2016

This paper discussed the LCL-type & Isolated bidirectional dc-dc converter(BDC) with dual full bridge inverter. In order to verify the analysis of the BDC, Experimental prototype has been designed and implemented to supply constant voltage regardless of loads and proposed a method to select switching frequency that depended on two inductors' inductance ratio and transformer parameters. The proposed converter has been composed of LCL resonant network with unit inductance ratio ($L_r/L_f$=1) and then operated with fixed duty, 50% duty ratio and fixed frequency. There are some characteristics that input voltage and output voltage of the BDC is nearly identical and zero voltage turn-on switching is possible in forward and reverse mode. Finally, it has been showed that BDC is possible to commutate operating mode normally and provide constant output voltage in selected switching frequency.

• 전력전자학회논문지
• /
• 제16권3호
• /
• pp.242-249
• /
• 2011

제안하는 컨버터는 부스트 하프브리지-전압 더블러를 각각 병렬-직렬로 연결하여 출력전력 및 출력전압을 증대시키므로 고승압 대전력 응용에서 소자의 선정이 용이하다. 특히 고주파변압기 턴 비를 작게 할 수 있고 DC 오프셋이 제거되어 최적의 변압기 설계가 가능하며, 3개의 코아로 전력이 분배되어 Low Profile 및 열 분산에 유리하다. 제안하는 컨버터는 전 영역(0 ∼ 1)의 듀티 사용으로 스타트업 및 추가의 클램프회로가 필요 없으며 입력전압 변동이 큰 응용에 적합하다. 또한 넓은 듀티영역에서 스위치의 ZVS 턴온과 다이오드의 ZCS 턴온 턴오프가 성취되므로 고효율을 달성할 수 있다. 제안하는 컨버터를 5 kW급 시작품으로 검증하였다.

• Journal of Power Electronics
• /
• 제19권2호
• /
• pp.363-379
• /
• 2019

Resonant converters have attracted a lot of attention because of their high efficiency due to the soft-switching performance. An isolated high step-up converter with secondary-side resonant loops is proposed and analyzed in this paper. By placing the resonant loops on the secondary side, the current stress for the resonant capacitors is greatly reduced. The power loss caused by the equivalent series resistance of the resonant capacitor is also decreased. Clamp diodes in parallel with the resonant capacitors ensure a unique discontinuous current mode in the converter. Under this mode, the active switches can realize soft-switching during both turn-on and turn-off transitions. Meanwhile, the reverse-recovery problems of diodes are also alleviated by the leakage inductor. The converter is essentially a step-up converter. Therefore, it is helpful for decreasing the transformer turn-ratio when it is applied as a high step-up converter. The steady-state operation principle is analyzed in detail and design considerations are presented in this paper. Theoretical conclusions are verified by experimental results obtained from a 500W prototype with a 35V-42V input and a 400V output.

• Journal of Power Electronics
• /
• 제8권4호
• /
• pp.363-370
• /
• 2008

In this paper, three kinds of PWM strategies for a three-phase current-fed dc/dc converter are proposed and compared in terms of losses and voltage transfer ratio. Each PWM strategy is described graphically and their switching losses are analyzed. With the proposed PWM C strategy, one turn-off switching of each bridge switch is eliminated to reduce switching losses under the same switching frequency. In addition, RMS current through the bridge switches is lowered by using parallel connection between two bridge switches and thus, conduction losses of the switches are reduced. Further, copper losses of the transformer are decreased due to the reduced RMS current of each transformer's winding. Therefore, total losses are minimized and the efficiency of the converter is improved by using the proposed PWM C strategy. Digital signal processor (DSP: TI320LF2407) and a field-programmable gate array (FPGA: EPM7128) board are used to generate PWM patterns for three-phase bridge and clamp MOSFETs. A 500W prototype converter is built and its experimental results verify the validity of the proposed PWM strategies.