• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.05a
• /
• pp.563-567
• /
• 2004

In this paper, a remote temperature sensor based on surface acoustic wave is introduced and the issues on design, manufacturing, and test of the sensor are addressed. SAW sensors having single and double electrode are prepared on the 128$^{\circ}$ YX-LiNbO$_3$ Substrate. The frequency responses of SAW sensors on the temperature change are compared. To measure the change of center frequency, two center frequencies on the 3dB and 20dB are measured and compared. Since the center frequency on the temperature change from -30$^{\circ}C$ to 80$^{\circ}C$ is linearly changed, the SAW sensor is applicable to the temperature sensor.

• Journal of Advanced Marine Engineering and Technology
• /
• v.28 no.2
• /
• pp.376-381
• /
• 2004

A rig was constructed to test the performance characteristics and compare the hydraulic forces exerted on a centrifugal type artificial heart impeller. A conventional shaft. seal and bearing system. while driven by a small electric motor. supported the impeller which was separated from the pump casing by a six degree of freedom force transducer (JR3 Ine). Radial (x. y) and axial (z) hydraulic forces were recorded and compared. At physiological operating conditions. the results indicate that the double entry/exit centrifugal pump encounters a smaller radial force and significantly reduced axial thrust. These experimental results are valuable in the design of a magnetic bearing system to suspend the impeller of a centrifugal artificial heart pump. This experimental technique may also be applied to evaluate the required capacity and predict the lifetime of contact bearings in marine pumps.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.13 no.1
• /
• pp.63-68
• /
• 2004

Recently ER fluids are put to practical use in fluid power industry field. As only with electrical signal change to the valve in which ER fluid flowing, ER fluid flow is controlled, so devepment of simple ER valves have been tried. In this case a technical problem is to check the pressure drop caused from flow rate change in valves because the pressure drop is very small. In this study ER valves are designed and manufactured, and small pressure drop induced from flow rate change is checked by pressure transducer which is made with appling strain gage. The ER valves and pressure drop check method are considered to be applied to the fluid power industry.

• 연구논문집
• /
• s.26
• /
• pp.51-56
• /
• 1996

In the case of a heat exchanger, scale is made in the tube by the chemical reactions of Ca and Mg ions contained in the water, and heat transfer rate is reduced because of increment of heat resistance in the pipe of the heat flow. Thus it brings to reduce the energy efficiency and to make environmental pollution by the use of chemicals for the prevention and removement of scale. In this paper, we discussed the design of electronic generator for ultrasonic scale preventor and analyzed the fundamental characteristic for ultrasonic transducer.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.10a
• /
• pp.83-89
• /
• 2000

This paper presents a dynamic modeling and a sliding mode controller for the high-speed / high-accuracy position control system. Selected target system is the wire bonder head assembly which is used in semiconductor assembly process. This system is a reciprocating one around the pivot point that consists of VCM(voice coil motor) as a actuator and transducer horn as a bonding tool. For the modeling elements, the system is divided into electrical circuit, magnetic circuit and mechanical system. Each system is modeled by using the bond graph method and united into the full system. Two major aims are considered in the design of the controller. The first one is that the horn must track the given reference trajectory. The second one is that the controller must be realizable by using the DSP board. Computer simulation and experimental results show that the designed sliding mode controller provides better performance than the PID controller.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.79-83
• /
• 2014

In this paper, SAW devices are fabricated using various IDT shape(Single/Double) to check an effect of the IDT on SAW device. And based on theory of a particle velocity moved by SAW and IDT, a particle velocity is measured and calculated. Depend on insert power, a particle velocity using Single-IDT SAW device is about two times bigger than Double-IDT SAW device and it's almost same with a theoretical different.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.733-735
• /
• 2014

The paper deals with the energy transmission ratio of the elastic waves obliquely transmitting through a plate and a pipe. The incidence angle corresponding to the maximum transmission was determined theoretically and considered in the design of ultrasonic transducers for flow velocimetry. Experimentally-obtained transmission ratios were compared with and confirmed the theoretically-calculated results.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.25 no.2
• /
• pp.124-132
• /
• 2015

The paper deals with the energy transmission of the elastic waves obliquely transmitting and refracting through a plate and a pipe. By calculating the transmitting ratio depending on the incidence angle, the angle corresponding to the maximum transmission was determined theoretically and considered in the design of ultrasonic transducers for flow velocimetry. Experiments were carried out by using prototypes of the transducers. Experimentally-obtained transmission ratios were compared with and confirmed the theoretically-calculated results.

• Journal of Sensor Science and Technology
• /
• v.4 no.3
• /
• pp.1-8
• /
• 1995

An electronically compensated current sensor for measurement of power is presented in this paper. An electronic technique which is proposed to design an improved current sensor by means of a feedback winding and an electronic compensation is described. A precision power transducer with a proposed current sensor has been constructed for testing and performance evaluation.

• Journal of the Microelectronics and Packaging Society
• /
• v.2 no.1
• /
• pp.69-75
• /
• 1995

압전세라믹스를 제조하여 발음체 소자의 두께 직경등의 칫수 변화에 따른 압전발을 체 소자의 전기적 특성 및 압전세라믹스와 금속진동판의 상관관계를 조사하고 공명용 수지 case등을 고려하여 공진 주파수에서 효율좋은 음을 발생시킬수 있는 압전발음체를 설계하였 다. 본 실험에서 사용딘 압전세라믹스 (Pb0.95Sr0.05)(Zr0.53Ti0.47)O3+0.8wt%Nb2O5의 특성은 전 기기계 결합계수(KP)가 69%이며 기계적 품질계수(Qm)은 87 비유전율은 2100 tan$\delta$는 0.016이었다. 금속진동판의 공진주파수는 사용되는 재료의 stiffness와 관계가 있고 주파수 -impedance 특성은 재질의 음속, 밀도, Young율 등에 크게 의존하였다. 주파수 대역 2.0~ 2.2khz에서 공진시키기 위한 공명체의 설계에서 압전세라믹스의 외경과 두께가 각각 14mm, 0.1mm 이고 금속진동판의 그것이 각각 20mm, 0.1mmdlfEo 공명기는 방음공의 직경이 3.0mm, cavity의 직경이 18.5mm, cavity의 높이가 4.5mm의 구조로 설계되었을때가 최적조 건이었다.