• The Journal of the Acoustical Society of Korea
• /
• v.24 no.7
• /
• pp.379-386
• /
• 2005

Among various kinds of hearing aids which have been developed so far. the conventional air conduction hearing aids have some problems such as the acoustic distortion, an howling effect due to acoustic feedback. Another type of hearing aid. the cochlear implant system can be applied to the profound imparied person. However. it shows the disadvantage that there is no possibility of recovery of the acoustic organ such as ossicle. On the other hand. the implantable middle ear heaving device directly vibratos the ossicular chain and has better sound qualify. good cosmetics for appearance. and wide frequency responses so that it can overcome the defects or the conventional hearing aids. In this paper, a mathematical modeling and a momentum equation derivation of the DET has been performed. For the optimization of the structure dimension generating maximal vibrating force of the DET. the computer simulation using a finite element analysis (FEA) software has been performed. Also. the vibrating transducer has been designed to make the frequency characteristics or the transducer be similar to those of the normal middle ear. Through the experimental results, the measured vibration characteristics of the DET has been evaluated to verify the performance for the application to implantable middle ear hearing devices.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.11 no.10
• /
• pp.1916-1923
• /
• 2007

We have studied to obtain the SAW filter for the passband was formed on the Langasite substrate and was evaporated by Aluminum-Copper alloy and thin we performed computer-simulated by simulator. We cm fabricate that the block weighted type IDT as an input transducer of the filter and the withdrawal weighted type IDT as an output transducer of the filter from the results of our computer-simulation. Also, we have performed to obtain the properly design conditions about phase shift of the SAW filter for WCDMA. We have employed that the number of pairs of the input and output IDT are 50 pairs and the thickness and the width of reflector are $5000\;{\AA}$ and $3.6{\mu}m$ respectively. And we have employed that the distances from the hot electrode to the reflector are $2.0{\mu}m$, $2.4{\mu}m$ and the distance from the hot electrode to the ground is $1.5{\mu}m$ respectively. Frequency response of the fabricated SAW filter has the property that the center frequency is about 190MHz and bandwidth at the 3dB is probably 7,8MHz. And we could obtain that return loss is less then -18dB, ripple characteristics is probably 3dB and triple transit echo is less then -25dB after when we have matched impedance.

• Journal of the Korean Geotechnical Society
• /
• v.22 no.12
• /
• pp.67-76
• /
• 2006

The reasonable assessment of the shear stiffness of a dredged soft ground and soft clay is difficult due to the soil disturbance. This study addresses the development and application of a new in-situ shear wave measuring apparatus (field velocity probe: FVP), which overcomes several of the limitations of conventional methods. Design concerns of this new apparatus include the disturbance of soils, cross-talking between transducers, electromagnetic coupling between cables, self acoustic insulation, the constant travel distance of S-wave, the rotation of the transducer, directly transmitted wave through a frame from transducer to transducer, and protection of the transducer and the cable. These concerns are effectively eliminated by continuous improvements through performing field and laboratory tests. The shear wave velocity of the FVP is simply calculated, without any inversion process, by using the travel distance and the first arrival time. The developed FVP Is tested in soil up to 30m in depth. The experimental results show that the FVP can produce every detailed shear wave velocity profiles in sand and clay layers. In addition, the shear wave velocity at the tested site correlates well with the cone tip resistance. This study suggests that the FVP may be an effective technique for measuring the shear wave velocity in the field to assess dynamic soil properties in soft ground.

• Journal of KSNVE
• /
• v.5 no.4
• /
• pp.577-583
• /
• 1995

The sandwich type piezoelectric resonator is widely used for the acoustic sources of underwater acoustic transducers, whose important design parameters are shapes, materials, dimensions and supporting methods. Practical design method of resonators consists of manufacturing, experiments and modification so that it requires much time and expenses. In this study, an analytical design method of sandwich type piezoelectric resonators is presented based on the nonlinear optimization technique. The proposed method is applied to the design of an example resonator model in order to maximize the output powers. For the investigation of performance according to the division and their electrical connection, three types of resonators are manufactured. In addition, their dynamic characteristics such as electrical admittance and transmitting voltage response are measured and compared.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.1041-1044
• /
• 2002

Inchworm linear motor is one of the ultra precision position apparatuses and has many kinds of forms and structures according to the conditions of working space and range. In this paper, the Inchworm linear motor consists of three PZTs(Piezo-electric transducer), three columns ma two plates. finite element method was used to determine the type or hinges installed in column of inchworm linear motor DOE(Design of experiment) was used to determine the optimal design condition of a column by comparing the von-mises stresses according to the change of thickness of hinge, round of hinge, height of arm, angle of v-notch, round of v-notch and thickness of column. From the result, round of hinge, height of arm and thickness of hinge were determined a effective design parameters.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.12
• /
• pp.1308-1315
• /
• 2009

A full-polarimetric scatterometer(HPS: Hongik Polarimetric Scatterometer) for X-band is designed, fabricated, and verified using the theoretically well-known point-targets in this paper. The X-band full-polarimetric scatterometer consists of an OMT(Orthogonal-Mode Transducer)+horn antenna, the angle control part for the OMT+horn antenna, a transmitter/receiver with a network analyzer and a frequency-conversion circuitry, and a movable support of these parts. We use an inclinometer sensor to control the vertical and horizontal incidence angles. The full polarimetric data can be obtained because of the polarization switches and the OMT. The accuracy of the scatterometer system is verified by measuring the polarimetric RCS(Radar Cross Section) of one of the theoretically well-known point-targets, i.e., a corner reflector.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.10 no.8
• /
• pp.921-926
• /
• 2015

For the over-heat protection purpose in power strip devices, over-current detection/protection circuits, such as bimetal, switching circuit, and microprocessor-based relay circuit, have been widely setup in high-end products. Most of these circuits are connected to the power line in parallel and, thus, they are sensitive to the line voltage and current distortion. Moreover, these protection circuits are often costly and, therefore, it is hard to meet the commercial requirements. A low-cost over-current detection circuit with the contactless current transducer is designed and tested in this paper. The detection circuit is galvanically isolated from the power line and, thus, less sensitive to the line voltage distortion. The experimental results show that the proposed circuit accurately operates despite of its simple structure and low-cost electronic parts.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.5 no.3
• /
• pp.563-572
• /
• 2001

A conventional motor in a crane has a taco generator to feed back the number of turns to a main controller. The taco generator is contacted to a motor shaft through the coupling. Errors in a crane have often occurred because the coupling has worn out while the motor is turning. In this paper, we design the device of the frequency to voltage transducer in a motor. The device is composed of a rotary encoder, a speed measurement using PIC16F84 controller, a display, and a direction-decision block. The rotation of a motor is recognized by the rotary encoder and microcontroller counts the number of turns of a motor. The emergency signal is generated if the frequency goes over or below the speed limit of a motor. And the device can acknowledge the rotation direction of the motor after 6。 rotation. The simulation results and the test for a implemented device have shown that the transducer of a frequency to a voltage can replace a taco generator in a crane.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.6
• /
• pp.914-919
• /
• 2000

A simple orthogonal mode transducer(OMT) for X-band has been proposed in this paper. This OMT is designed such that a polarized wave can be guided in a direction using several thin guiding posts, and the other orthogonally polarized wave can be guided in the other direction using other thin guiding posts. The OMT consists of a T-shaped waveguide section with guiding posts, two tapering waveguide arms, and has three flanges for connection with two adapters and an antenna. The optimum numbers and the optimum positions of the guiding posts were obtained numerically using the HFSS CAD tool. The isolation between two polarizations in a manufactured OMT is higher than 42.8 dB and the reflection from the OMT is lower than -17.5 dB at the frequency band of 9.5 GHz

• Journal of the Korean Society for Nondestructive Testing
• /
• v.27 no.4
• /
• pp.313-320
• /
• 2007

Recently, a new class of single-crystal piezoelectric materials such as lead metanibobate doped with lead titanate (PMN-PT) has been synthesized and were found to further enhance the electro-mechanical coupling factor compared to piezo-ceramic materials. This paper describes fabrication and evaluation of PMN-PT single crystal ultrasonic transducers for contact measurement of stainless steel that is one of the highly attenuative materials. The design conditions for ultrasonic transducer such as front matching layer between test materials and piezo-material and backing materials were investigated based on the simulation results by KLM model. The PMN-PT single crystal ultrasonic transducers with centre frequencies at 1 and 2.25 MHz were fabricated and their performances were evaluated.