DOI QR코드

DOI QR Code

The basic experiments for the fabrication of the SPUDT type Inter using the SFIT type filter

SFIT형태를 이용한 SPUDT형 필터제작에 관한 기초실험

  • 유일현 (세명대학교 컴퓨터 응용 과학과)
  • Published : 2007.10.31

Abstract

We have studied to obtain the SAW filter for the passband was formed on the Langasite substrate and was evaporated by Aluminum-Copper alloy and thin we performed computer-simulated by simulator. We cm fabricate that the block weighted type IDT as an input transducer of the filter and the withdrawal weighted type IDT as an output transducer of the filter from the results of our computer-simulation. Also, we have performed to obtain the properly design conditions about phase shift of the SAW filter for WCDMA. We have employed that the number of pairs of the input and output IDT are 50 pairs and the thickness and the width of reflector are $5000\;{\AA}$ and $3.6{\mu}m$ respectively. And we have employed that the distances from the hot electrode to the reflector are $2.0{\mu}m$, $2.4{\mu}m$ and the distance from the hot electrode to the ground is $1.5{\mu}m$ respectively. Frequency response of the fabricated SAW filter has the property that the center frequency is about 190MHz and bandwidth at the 3dB is probably 7,8MHz. And we could obtain that return loss is less then -18dB, ripple characteristics is probably 3dB and triple transit echo is less then -25dB after when we have matched impedance.

대역통과용 표면 탄성파 필터 제작하기 위하여 Langasite 기판위에 빗살무의 변환기를 형성 시켜 모의실험을 수행하였으며, 전극재료로는 Al-Cu를 사용하였다. 모의실험을 바탕으로 입력단에는 IDT를 직렬형태로 연결시킨 block 형태로 하중을 가하는 전극 방법을 쓰고 출력 단은 withdrawal 형태로 하중을 가하는 방법을 써서 제작하였다. 이를 바탕으로 광대역의 SAW 필터 전극 설계 방식에 대한 적절한 위상조건도 얻고자 시도하였다. Langasite 기판위에 형성시킨 입출력 빗살무의 변환기 전극 수는 50쌍, 두께는 $5000\;{\AA}$으로 하였으며, 반사기 폭은 $3.6{\mu}m$으로 하였다. 그리고 hot전극과 반사기사이의 거리는 각각 $2.0{\mu}m\;2.4{\mu}m$로 제작하였고, hot전극에서부터 접지전극까지 간격은 $1.5{\mu}m$로 하였으며 전극 모양은 좌우 동일한 형상을 채택하였다. 제작한 필터의 주파수 특성은 중심주파수가 대략 190MHz정도, 대역폭은 7.8MHz 이하로 측정되었으며, matching 후 return-loss는 -18dB 이하이고, 리플 특성은 3dB 이하이며, 반사에 의한 잔향은 -25dB 이하로 측정되었다.

Keywords

References

  1. C. S. Hartman, D. T. Bell, Jr., and R. C. Rosenfeld, Impulse Model Design of Acoustic Surface Wave Filters, IEEE Trans. Microwave Theory and Techniques, vol.MTT-21, No.4, pp.162-175, 1973
  2. G. L. Matthae, Acoustic Surface Wave Transversal Filters, IEEE Trans. Circuit and Theory, vol.CT-20, No.5, pp. 459-470, 1973
  3. R. H. Tancrell, Analytic Design of Surface Wave Bandpass Filters, IEEE Trans. Sonics Ultrason., vol.SU-21, No.1, pp.12-22, 1974
  4. T. Thorvaldsson, Analysis of The Natural Single Phase Unidirectional SAW Transducer, IEEE Trans. Ultrasonic Sym., pp.91-96, 1989
  5. H. Yatsuda, K. Yamanouchi, Automatic CAD Design of SAW Filters Using Slanted Finger Interdigital Transducer, IEEE Trans. Sonics UFFC, vol.47, No.1, pp.140, 2000 https://doi.org/10.1109/58.818756
  6. H. Yatsuda, Design techniques for SAW filters using slanted finger interdigital transducers, IEEE Trans. Sonics UFFC, vol.44, No.1, pp.453, 1997 https://doi.org/10.1109/58.585130
  7. C. B. Chvets, P.G. Ivanov, V. M. Maka, V. S. Orlov, Design of SAW Filters on Langasite, IEEE Ultrasonic Symposium, pp.99. 1999
  8. 유일현, 권희두, 경사진 빗살무늬 변환기를 이용한 대역통과 필터제작, 한국 해양정보통신학회, vol.9, No.2, pp308, 2005
  9. 유일현, 단상 단방향 형태의 표면탄성파 필터 제작 및 임피던스 정합, 한국 해양정보통신학회, Vol.9, No.3, pp602, 2005