• 한국환경과학회지
• /
• 제15권12호
• /
• pp.1141-1154
• /
• 2006

Orographic effect is one of the important factors to induce Local circulations and to make atmospheric turbulence, so it is necessary to use the exact topographic data for prediction of local circulations. In order to clarify the sensitivity of the spatial resolution of topography data, numerical simulations using several topography data with different spatial resolution are carried out under stable and unstable synoptic conditions. The results are as follows: 1) Influence of topographic data resolution on local circulation tends to be stronger at simulation with fine grid than that with coarse grid. 2) The hight of mountains in numerical model become mote reasonable with high resolution topographic data, so the orographic effect is also emphasized and clarified when the topographic data resolution is higher. 2) The higher the topographic resolution is, the stronger the mountain effect is. When used topographic data resolution become fine, topography in numerical model becomes closer to real topography. 3) The topographic effect tends to be stronger when atmospheric stability is strong stable. 4) Although spatial resolution of topographic data is not fundamental factor for dramatic improvement of weather prediction accuracy, some influence on small scale circulation can be recognized, especially in fluid dynamic simulation.

• 한국지구과학회지
• /
• 제32권2호
• /
• pp.190-199
• /
• 2011

지형 효과가 포함된 태양복사 모델(GWNU)을 이용한 한반도의 태양광 자원지도를 개발하였다. 태양복사 모델의 입력 자료는 위성 관측 자료(MODIS, OMI, MTSAT-1R)와 수치 모델(RDAPS) 자료를 사용하였으며 특히 고해상도 지형 자료를 이용하여 지형 효과에 따른 한반도의 지표면 태양광 변화를 계산하였다. 계산 결과를 월 및 연 누적하여 분석하였을 때 여름철은 태양 고도각이 높아 지형 효과에 영향이 10% 이하로 적은 반면 겨울철은 20% 이상의 큰 차이가 나타났다. 또한 4 km 해상도의 지표면 태양광의 경우보다 1 km 해상도의 경우 지형 효과 포함에 따른 태양광 차이가 약 2배 정도 크게 나타났다. 즉 지표면에 도달하는 태양광을 정확히 모델링하기 위해서는 입력 자료뿐만 아니라 정확하고 고해상도의 지형 자료가 필연적이며 지형효과는 더욱 뚜렷이 나타나 실제와 유사할 것이다.

• 한국의류산업학회지
• /
• 제3권3호
• /
• pp.235-240
• /
• 2001

This paper was intended to grasp an effect of body shaping by wearing girdle using moire topography. In wearing test, four type girdle were used, panty type, long leg type, high waist type, long leg and high waist type. Subjects were ten female college student (18-24 years old), they were selected on the size of the hip girth, waist girth that are within 25~75% in percent on the National Anthropometric survey of Korea in 1997. Three-dimentional characteristic of body shaping was analyzed by the moire topograph. As a result, body shaping effect was confirmed by moire pattern and horizantal section map. In case of the comparison through the moire topography, all the subjects have an effect on body shaping in part of waist girth, abdomen, and hip. Especially backside silhouettes on hip all the ten female subjects showed hip-up effect. Long leg type girdle was smooth side line in the hip and thigh. Further study required for the effect of wearing the girdle on the body shapeability and comfort.

• Environmental Analysis Health and Toxicology
• /
• 제23권1호
• /
• pp.47-51
• /
• 2008

The toxicity of environmental pollutants was measured between a image of the surface topography in HeLa cells using atomic force microscopy for the possibility of toxic effect measurement and environmental monitoring. A image of the surface topography by AFM were estimated as toxic endpoints. The surface topography by AFM was observed a change of the cell surface in the environmental pollutants, but the standard of the measurement requires for the dose-effect degree. The overall results indicate that the possibility of measurement using AFM were confirmed a dose-effect degree related toxic effects, but it requres correlation between more various biomarker and AFM's measurements if the possibility of the toxic effect measurement was established.

• 대한기계학회논문집A
• /
• 제24권7호
• /
• pp.1681-1688
• /
• 2000

A dynamic model for the prediction of surface topography in high speed end milling process is developed. In this model the effect of tool runout, tool deflection and spindle vibration were taken in to account. An equivalent diameter of end mill is obtained by finite element method and tool deflection experiment. A modal parameter of machine tool is extracted by using frequency response function. The tool deflection, spindle vibration chip thickness and cutting force were calculated in dynamic cutting condition. The tooth pass is calculated at the current angular position for each point of contact between the tool and the workpiece. The new dynamic model for surface predition are compared with several investigated model. It is shown that new dynamic model is more effective to predict surface topography than other suggested models. In high speed end milling, the tool vibration has more effect on surface topography than the tool deflection.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2000년도 춘계학술대회논문집 - 한국공작기계학회
• /
• pp.613-617
• /
• 2000

This paper descries the effect of the stylus tip size on the measuring error in surface topography measurement. To analyze the distortional effect of an actual surface geometry originating from the finite stylus size, the surface is modeled as a sinusoid and the stylus tip as a circle. the measuring error is defined as the ratio of the standard deviation of a tracing profile and an original profile. It is shown that this measuring error depends on the amplitude and wavelength of an original profile. In this paper, the spectrum analysis is applied to investigate the distortional effect due to the mechanical filtering of the stylus in the frequency domain. and, the cumulative power spectrum is applied to determinate the minimum wavelength limits to be measured with the various stylus tip radius from these results, a new method to select proper stylus tip radius is proposed.

• Earthquakes and Structures
• /
• 제20권2호
• /
• pp.187-200
• /
• 2021

The main factor for the amplification of ground motions near the crest or the toe of a slope is the reflection of the incident waves. The effects of the slope topography on the surrounding lands over the crest or at the toe can amplify the seismic responses of buildings. This study investigates the seismic performance of the slope topography and three mid-rise buildings (five, ten, and fifteen-storey) located near the crest and toe of the slope by 3D numerical analysis. The nonlinear model was used to represent the real behavior of building and ground elements. The average results of seven records were used in the investigations. Based on the analysis, the amplification factor of acceleration near the crest and toe of the slope was the most effective at distances of 2.5 and 1.3 times the slope height, respectively. Accordingly, the seismic performance of buildings was studied at a distance equal to the height of the slope from the crest and toe. The seismic response results of buildings showed that the slope topography to have little impact on up to five-storey buildings located near the crest. Taking into account a topography-soil-structure interaction system increases the storey displacement and base shear in the building. Accordingly, in topography-soil-structure interaction analyses, the maximum lateral displacement was increased by 71% and 29% in ten and fifteen-storey buildings, respectively, compare to the soil-structure interaction system. Further, the base shear force was increased by 109% and 78% in these buildings relative to soil-structure interaction analyses.

• 한국수산과학회지
• /
• 제22권6호
• /
• pp.375-384
• /
• 1990

A numerical experiment is made to study the combined effect of differential cooling and bottom topography on the formation of Ulleung Warm Eddy. The Ulleung Warm Eddy appears after the passage around the Ulleung Basin of coastal trapped baroclinic waves generated in the north initial density front to the north, the continental slopes both to the west and south, and the Yamato Rise to the east. It resides therefore always inside the Ulleung Basin, as confirmed by observations.

• 대한기계학회논문집A
• /
• 제24권2호
• /
• pp.311-318
• /
• 2000

Several factors which influence baseline instability (BLI) phenomenon in MR drive were investigated experimentally. In particular, the role of surface topography on BLI was studied in detail. The r esults show that BLI is linearly proportional to the surface waviness with a spatial wavelength of 0.4 to 5.0 min. BLI becomes worse as the surface waviness increases. On the other hand, surface roughness which has a spatial wavelength below 25 $\mu$ m has no effect on BLI. The results further show that the effect of bias current on the BLI is amplified on the disk with worse surface waviness. The disk surface waviness is dependent on the manufacturing process and becomes an inherent surface property of media. The disk surface waviness. therefore, can not be overlooked when evaluating the media for a high-performance hard disk drive. In general, waviness is reduced mainly during grinding and polishing process during manufacturing.

• 지구물리와물리탐사
• /
• 제27권1호
• /
• pp.37-50
• /
• 2024

MT 탐사는 측점 주변의 지형과 바다와 같은 외부적 환경 요인에 의해서도 자료에 영향을 받는데, 특히 섬에서 수행된 MT 탐사 자료에는 지형효과와 해양효과가 복합적으로 작용하게 되며, 올바른 해석을 위해서는 두 효과에 대한 이해가 필요하다. 본 연구에서는 지형과 해양의 영향이 포함된 MT 반응(겉보기비저항, 위상)을 분석하기 위해 깊은 바다에 둘러싸인 원뿔 형태의 소규모 섬 모델을 생성하였다. 지형만을 고려한 지형모델, 지형과 바다를 동시에 고려한 섬 모델에 대하여 2차원 순산모델링과 3차원 순산모델링을 수행하고 MT 반응을 확인하였다. 3차원 섬 모델에 대해 2차원 모델링을 수행하면, 측선의 직교 방향에 대한 지형 변화와 바다를 고려하지 못하는데, 3차원 모델링을 수행함으로써 모든 방향의 지형 변화와 섬을 둘러싼 바다를 고려한 MT 반응을 얻을 수 있었다. 언덕과 같이 주변의 기복이 심한 지형에서는 겉보기비저항 XY 성분과 YX 성분의 벌어짐 현상이 전형적으로 발생하였다. 저비저항 이상체가 해수면 아래 1 km 심도에 존재할 경우, MT 반응에서 지형과 바다로 인한 변동과 구분할 수 있으며, 심도 증가에 따라 이상체의 영향이 감쇠하였다. 다양한 조건에서 모델링을 수행하고 MT 반응을 분석함으로써, 현장 MT 자료에 대한 이해를 높이고 자료 해석에 도움이 될 수 있을 것으로 기대한다.