• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.1
• /
• pp.412-415
• /
• 2003

[ $Si_3N_4$ ] thin film is the good material to fabricate the capacitors at MMIC processes. Normally, $Si_3N_4$ thin films is used to dielectric in the MIM capacitor and film thickness is $2000\;{\AA}$. Insulator(or dielectric) was deposited by PECVD at our MIM structure with air bridge which connect between top metal and contact pad. We optimized PECVD process to fabricate the good capacitors which can be applied at the true MMIC. The thickness of our $Si_3N_4$ thin films was $1000\;{\AA}$ shallower than $2000\;{\AA}$, and their breakdown voltages were above 70V.

• 한국생산제조학회지
• /
• 제23권6호
• /
• pp.624-629
• /
• 2014

The purpose of this study is to carry out the task of engine hesitation which occurred intermittently in driving due to the defective CKPS of LPI vehicles. As the result of the wrong data from the equipment of D-logger, the signal error of CKPS caused the engine hesitation. We performed a study in the followings to analyze and investigate the cause effectively. First, we have investigated the control wiring harness and connector pin contact defect inspection. Second, we have inspected the defection of CKPS separately. From this study, it was found that the engine hesitation were caused by the bad durability and we have showed how to diagnosis the fault of the engine hesitation intermittently while driving. Therefore, it is determined that we have to improve the durability of the CKPS through a strict quality control and to increase the reliability.

• 미생물학회지
• /
• 제12권3호
• /
• pp.147-148
• /
• 1974

A small amount of Duco cement or Elmer's clear cement was dropped on a slide glass and immediately spread with a glass rod or woden stick a thin film on the surface. After approximately 1 minute a small amount of rubber cement was spread on the top of the film of Duco cement using the same method as described earlier. It was important that the rubber cement be smeared before the Duco cement dried out. These two kinds of cements must not be mixed. It was better to make the film of the rubber cement slightly thicker than the film of Duco cement. This composite film may be used up to several months after preparation. The sample leaf was placted on the slide, prepared with adhesive and the leaf surface was passed on the film with the thumb. The pressing was done so the leaf surface was completely in contact with the film. Then the leaf was peeled from the slide.

• 자원환경지질
• /
• 제32권1호
• /
• pp.33-41
• /
• 1999

A new sedimentary basin is reported from the marine multi-channel seismic data which were acquired for the hydrocarbon exploration on the southwestern Korean continental shelf in 1970. Along the southeastern part of Line 1192, the about 60-km-long basin with the thickness of 0.55~1.1 s is observed on the near-trace gather. However, both new and previous 24-fold stack sections fail to show the basin image probably due to its rugged top beneath the shallow water. The boundary contact between the basement with the velocity of about 5200m/s and the basin filling with the velocities of 4300~4700 m/s is unclear. These velocites are calculated from the corresponding shot gathers. Compared with the Haenam Basin, a neighbouring onshore Cretaceous sedimentary basin, we interpret that the new basin includes the volcanics and volcaniclastic sequences deposited in the lacustrine environment. This nonmarine basin was possibly formed as the result of the tectonic movement during the Cretaceous, implying the wide occurrence of the Cretaceous basins over the southern Korean Peninsula as well as its southwestern continental shelf.

• 한국가구학회지
• /
• 제13권1호
• /
• pp.42-47
• /
• 2002

The folding chairs are one of the most necessary furniture for satisfying the moderns' wants which is utilized for limited space rationally. These folding chairs are variously used in interior spaces such as offices, dining areas, and resting areas. They are very easy to move around, so that quiet useful in out door areas, too. Moreover, they play an important role in public spaces as supplementary furniture. The folding chairs have one or several axes, and they are classified according to type of axes like below. 1. Method of divide seating board into 2 and fold, 2. Method of folds seating board and lay on bottom of backboard, 3. Method of fold back board and lay on top of seating board, 4. Method of fold into contact with left and right, 5. Method of gathering legs into one and fold. The folding chairs have to be easy to operate, firm and safe, light for moving around easily, designed for able to change units whenever they have damaged. Change of residential spaces according to the trend towards the nuclear family maximized necessity of limited spaces' use. Therefore, this study provides insights for development of new methods' of folding chairs.

• 한국자동차공학회논문집
• /
• 제8권3호
• /
• pp.1-11
• /
• 2000

Instantaneous temperature probes were manufactured by pressing method. By using these probes, the instantaneous surface temperature and unsteady heat flux in the cylinder liner of DOHC engine were measured. The main results are as follows; ⅰ) the instantaneous surface temperature of cylinder liner are affected by the contact of piston ring as well as burning gas. ⅱ) the wall temperature of the siamese portion is much higher than other parts. ⅲ) it was shown that the rising trend of heat flux by burning gas are nearly limited to the 1/2-stroke distance from the top of cylinder liner.

• 한국자동차공학회논문집
• /
• 제5권6호
• /
• pp.141-147
• /
• 1997

For the effective finite element analysis of the structures including material interfaces or contact surfaces, interface elements are proposed. Most of early works in this problem require not only iterative computation but also complex formulation because of the kinematic nonlinearities caused from the discontinuous behavior and the stress concentration phenomena. The proposed elements, however, are consistently formulated using relative displacements and tractions between top and bottom regular finite elements. The effectiveness of these elements are shown by solving various numerical sample problems including an leaf spring and comparing with results of general finite element analysis. As a result, more stable solutions are conveniently obtaines using interface elements than regular finite elements.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.978-979
• /
• 2006

In this study, bottom-up type powder processing and top-down type SPD (severe plastic deformation) approaches were combined in order to achieve both full density and grain refinement of metallic powders with least grain growth. ECAP (Equal channel angular pressing) was used for the powder consolidation. We investigated the consolidation, plastic deformation and microstructure evolution behavior of the metallic powders during ECAP using an experimental method. It was found that high mechanical strength could be achieved effectively as a result of the well bonded powder contact surface during ECAP process of gas atomized Al-Si powders.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.506-507
• /
• 2008

Organic field-effect transistors (OFETs) are of interest for use in widely area electronic applications. We fabricated a copper phthalocyanine (CuPc) based field-effect transistor with different metal electrode. The CuPc FET made a top-contact type and the substrate temperature was room temperature. The source and drain electrodes were used an Au and Al materials. The CuPc thickness was 40nm, and the channel length was $50{\mu}m$, channel device was width was 3mm. We observed a typical current-voltage (I-V) characteristics in CuPc FET with different electrode materials.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 춘계학술대회 논문집
• /
• pp.12-13
• /
• 2008

Organic field-effect transistors (OFETs) are of interest for use in widely area electronic applications. We fabricated a copper phthalocyanine (CuPc) based field-effect transistor with different metal electrode. The CuPc FET device was made a top-contact type and the substrate temperature was room temperature. The source and drain electrodes were used an Au and Al materials. The CuPc thickness was 40nm, and the channel length was $50{\mu}m$, channel width was 3mm. We observed a typical current-voltage (I-V) characteristics in CuPc FET with different electrode materials.