• Korean Chemical Engineering Research
• /
• v.45 no.4
• /
• pp.335-339
• /
• 2007

In order to overcome the problem of poor hardness of transparent polycarbonate (PC) sheets, organic-inorganic hybrid hard coating solutions, which show a high refractive index above 1.58, were made by the sol-gel method. These hybrid coating solutions were obtained from mixture of titanium tetraisopropoxide (TTIP), and (3-glycidoxypropyl)trimethoxysilane (GPTMS). The PC sheets were spin-coated, and cured at $120^{\circ}C$ for 2 hr. Change of refractive index in the range of 1.53-1.61 was obtained by varying the GPTMS content. The refractive index of the coated film decreased with increasing the GPTMS content, while the pencil hardness of the coated film was found to increase with increasing the GPTMS content.

• Bulletin of the Korean Chemical Society
• /
• v.25 no.11
• /
• pp.1661-1666
• /
• 2004

The reaction of titanium tetraisopropoxide with 2 equiv of N,N-diethyl acetoacetamide affords Ti($O^iPr)_2(CH_3COCHCONEt_2)_2$ (1) as colorless crystals in 80% yield. Compound 1 is characterized by spectroscopic (Mass and $^1H/^{13}C$ NMR) and microanalytical data. Molecular structure of 1 has been determined by a single crystal X-ray diffraction study, which reveals that it is a monomeric, cis-diisopropoxide and contains a six coordinate Ti(IV) atom with a cis($CONEt_2$), trans($COCH_3$) configuration (1a) in a distorted octahedral environment. Variable-temperature $^1H$ NMR spectra of 1 indicate that it exists as an equilibrium mixture of cis, trans (1a) and cis, cis (1b) isomers in a 0.57 : 0.43 ratio at -20$^{\circ}C$ in toluene-$d_8$ solution. Thermal properties of 1 as a MOCVD precursor for titanium dioxide films have been evaluated by thermal gravimetric analysis and vapor pressure measurement. Thin films of pure anatase titanium dioxide (after annealing above 500$^{\circ}C$ under oxygen) have been grown on Si(100) with precursor 1 in the substrate temperature range of 350- 500$^{\circ}$ using a bubbler-based MOCVD method.

• Nano
• /
• v.13 no.10
• /
• pp.1850124.1-1850124.12
• /
• 2018

$TiO_2$ films were deposited from oxygen/titanium tetraisopropoxide (TTIP) plasmas at low temperature by Helicon-PECVD at floating potential ($V_f$) or substrate self-bias of -50 V. The influence of titanium precursor partial pressure on the morphology, nanostructure and optical properties was investigated. Low titanium partial pressure ([TTIP] < 0.013 Pa) was applied by controlling the TTIP flow rate which is introduced by its own vapor pressure, whereas higher titanium partial pressure was formed through increasing the flow rate by using a carrier gas (CG). Then the precursor partial pressures [TTIP+CG] = 0:027 Pa and 0.093 Pa were obtained. At $V_f$, all the films exhibit a columnar structure, but the degree of inhomogeneity is decreased with the precursor partial pressure. Phase transformation from anatase ([TTIP] < 0.013 Pa) to amorphous ([TTIP+CG] = 0:093 Pa) has been evidenced since the $O^+_2$ ion to neutral flux ratio in the plasma was decreased and more carbon contained in the film. However, in the case of -50 V, the related growth rate for different precursor partial pressures is slightly (~15%) decreased. The columnar morphology at [TTIP] < 0.013 Pa has been changed into a granular structure, but still homogeneous columns are observed for [TTIP+CG] = 0:027 Pa and 0.093 Pa. Rutile phase has been generated at [TTIP] < 0:013 Pa. Ellipsometry measurements were performed on the films deposited at -50 V; results show that the precursor addition from low to high levels leads to a decrease in refractive index.

• Journal of Korean Society on Water Environment
• /
• v.26 no.4
• /
• pp.707-712
• /
• 2010

Nitrogen-doped $TiO_2$ particles have been successfully prepared using titanium tetraisopropoxide as the Ti source and urea as the nitrogen source. As-prepared nitrogen-doped $TiO_2$ was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), Brunauer-Emmett-Teller method (BET) and ultraviolet-visible light (UV-vis) absorption spectra techniques. Photocatalytic degradation of Methylene Blue (MB) has been carried out in both solar light (UV-vis) and the visible region (${\lambda}=420nm$). Nitrogen-doped $TiO_2$ exhibits higher activity than the commercial $TiO_2$ photocalyst, particularly under visible-light irradiation because bandgap of nitrogen-doped $TiO_2$ becomes remarkably decreased.

• Journal of Powder Materials
• /
• v.10 no.6
• /
• pp.448-455
• /
• 2003

$TiO_2$ nanopowder has been synthesized by means of the flame method using a precursor of titanium tetraisopropoxide (TTIP, Ti$(OC_3H_7)_4)$. In order to clarify the effect of cooling rate of hot flame on the formation of $TiO_2$ crystalline phases, the flame was controlled by varying the mixing ratio and the flow rate of gases. Anatase phase was predominantly synthesized under the condition having the steep cooling gradient in flame, while a slow cooling gradient enabled to form almost rutile $TiO_2$ nanopowder of above 95%.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.9 no.1
• /
• pp.11-18
• /
• 2003

The pure $TiO_2$ particles have been prepared in vapor-phase hydrolysis of titanium tetraisopropoxide(TTIP). The rate of TTIP hydrolysis was so fast that the overall rate of formation of $TiO_2$ was controlled by the rate of mixing of TTIP and $H_2O$. Thus, the primary $TiO_2$ particles were prepared in nano sizes to form chainlike aggregates due to rapid coagulation. The pure $TiO_2$ particles as prepared were amorphous at the reactor set temperatures below $400^{\circ}C$ and became anatase at the temperatures of $450^{\circ}C$ above while the weak rutile peaks were also observed above $800^{\circ}C$. The actual size of primary particles as prepared were reduced by increasing the reactor set temperature while their crystalline sizes as well as BET sizes increased by post-sintering.

• Environmental Engineering Research
• /
• v.13 no.4
• /
• pp.171-176
• /
• 2008

Studies on visible-light-driven photocatalysis of air pollutants at indoor air quality (IAQ) levels have been limited. Current study investigated visible-light derived photocatalysis with N-doped and S-doped titanium dioxide ($TiO_2$) for the control of benzene at indoor levels. Two preparation processes were employed for each of the two types of photocatalyst: urea-Degussa P-25 $TiO_2$ and titania-colloid methods for the N-doped $TiO_2$; and titanium isopropoxid- and tetraisopropoxide-thiourea methods for the S-doped $TiO_2$. Furthermore, two coating methods (EDTA- and acetylacetone-dissolving methods) were tested for both the N-doped and S-doped $TiO_2$. The two coating methods exhibited different photocatalytic degradation efficiency for the N-doped photocatalysts, whereas they did not exhibit any difference for the S-doped photocatalysts. In addition, the two doping processes showed different photocatalytic degradation efficiency for both the S-doped and N-doped photocatalysts. For both the N-doped and S-doped $TiO_2$, the photocatalytic oxidation (PCO) efficiency increased as the hydraulic diameter (HD) decreased. The degradation efficiency determined via a PCO system with visible-light induced $TiO_2$ was lower than that with UV-light induced unmodified $TiO_2$, which was obtained from previous studies. Nevertheless, it is noteworthy that for the photocatalytic annular reactor with the HD of 0.5 cm, PCO efficiency increased up to 52% for the N-doped $TiO_2$ and 60% for the S-doped $TiO_2$. Consequently, when combined with the advantage of visible light use over UV light use, it is suggested that with appropriate HD conditions, the visible-light-assisted photocatalytic systems can also become an important tool for improving IAQ.

• Korean Chemical Engineering Research
• /
• v.53 no.6
• /
• pp.776-782
• /
• 2015

$TiO_2-SnO_2$ nanoparticles with an average diameter of 3~5 nm were synthesized by hydrolysis of titanium tetraisopropoxide (TTIP) and tin chloride to depress the photocatalytic activity of $TiO_2$ nanoparticles. Organic-inorganic hybrid coating solutions were prepared by reacting the $TiO_2-SnO_2$ nanoparticles with 3-glycidoxypropyl trimethoxysilane (GPTMS) by the sol-gel method. The hard coating films with high refractive index were obtained by curing thermally at $120^{\circ}C$ after spin-coating the coating solutions on the polycarbonate (PC) sheets. The coating films from $TiO_2-SnO_2$ nanoparticles showed an improved pencil hardness of 3H compared to 2H of the coating films from $TiO_2$ nanoparticles. Besides, the refractive index of the coating films from $TiO_2-SnO_2$ nanoparticles enhanced from 1.543 to 1.623 at 633 nm as the Sn/Ti molar ratio increased from 0 to 0.5.

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.4
• /
• pp.765-773
• /
• 2000

The degradation of humic acid using $TiO_2$ coatings was studied, $TiO_2$ coatings were prepared by dip-coating method. Sol solutions for coating were prepared by mixing the gel, which can be produced by the reaction of $TiOCl_2$ and $NH_4OH$ solution, and hydrogen peroxide solution, and hydrolysis of titanium tetraisopropoxide (TTIP). It was shown from XRD that coatings from sol aged at $100^{\circ}C$ for 18h with titanium peroxo solution were crystallized to anatase in the range of temperatures of $25^{\circ}C$ to $500^{\circ}C$. In contrast, those coated from TTIP were crystallized to anatase at temperature above $400^{\circ}C$. So the sols originated from $TiCl_4$ can be applied for not only on the heat-resistance substrates but on the plastic substrates. Thickness and the quality of the films were dependent on the withdrawing speed, the concentration of sol, and the number of coating. The films showed various interference colors depending on the thickness of them. In the case that the films coated 2 times at withdrawing speed of 2.5cm per minute by 0.2M sol, the films had a transparent light blue color with thickness of around 50nm. It was known from the result of photo-degradation by $TiO_2$ coatings using humic acid that the removal efficiency of $COD_{cr}$ was over 85% after illumination of $UV/H_2O_2$ for 40min. and that of UV/VIS absorbable materials was over 95%.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.2
• /
• pp.344-350
• /
• 2010

The improved photocatalytic performance of a carbon/$TiO_2$ composite was studied for the Bisphenol A (BPA) decomposition. Titanium tetraisopropoxide (TTIP) and a rice husk from Korea were heterogeneously mixed as the titanium and carbon sources, respectively, for 3 h at room temperature, and then thermally treated at $600^{\circ}C$ for 1 h in $H_2$ gas. The transmission electron microscopy (TEM) images revealed that the bulk carbon partially covered the $TiO_2$ particles, and the amount that was covered increased with the addition of the rice husk. The acquired carbon/$TiO_2$ composite exhibited an anatase structure and a novel peak at $2{\theta}=32^{\circ}$, which was assigned to bulk carbon. The specific surface area was significantly enhanced to 123~164 $m^2/g$ in the carbon/$TiO_2$ composite, compared to $32.43m^2/g$ for the pure $TiO_2$. The X-ray photoelectron spectroscopy (XPS) results showed that the Ti-O bond was weaker in the carbon/$TiO_2$ composite than in the pure $TiO_2$, resulting in an easier electron transition from the Ti valence band to the conduction band. The carbon/$TiO_2$ composite absorbed over the whole UV-visible range, whereas the absorption band in the pure$TiO_2$ was only observed in the UV range. These results agreed well with an electrostatic force microscopy (EFM) study that showed that the electrons were rapidly transferred to the surface of the carbon/$TiO_2$ composite compared to the pure $TiO_2$. The photocatalytic performance of the BPA removal was optimized at a Ti:C ratio of 9.5:0.5, and this photocatalytic composite completely decomposed 10.0 ppm BPA after 210 min, whereas the pure $TiO_2$ achieved no more than 50% decomposition under any conditions.