• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.5 no.3
• /
• pp.278-283
• /
• 1995

The potassium titanate fibres were synthesized with wet process by the addition of KOH solution to the TiOz gel produced by the reaction between element titanium particles and $H_2O_2$ solution at $50^{\circ}C$. And then they were characterized by XRD, SEM and FT - IR. It was found that potassium titanate fibres were mainly affected by KOH/TiOz mole ratio, synthesis time and aging time in this wet process employed. For $KOH/TiO_2 = 1/1$, synthesizing time 24 hrs, aging time 24 hrs and calcination temperature of TEX>$900^{\circ}C$ for 1 hr, their products were mainly found to be potassium tetratitanate which had thin and long fibres in the range of 10 ~ 20 mm. As the synthesizing time increased and the amount of KOH decreased, potassium tetratitanate was converted into potassium hexatitanate. Also, the length of their fibres became short.

• Transactions on Electrical and Electronic Materials
• /
• v.12 no.5
• /
• pp.222-225
• /
• 2011

Lead zirconate titanate (PZT) films were fabricated on Pt/Ti/$SiO_2$/Si substrate by the sol-gel method using a sol containing poly(N-vinylpyrrolidone) (PVP). PVP in alkoxide solutions can suppress the condensation reaction in gel films during heat treatment, and increase the viscosity of alkoxide solutions. Single-phase PZT films as thick as 1 ${\mu}m$ were deposited by repetitive coating with successive third-step heat treatments at 150$^{\circ}C$, 350$^{\circ}C$ and 650$^{\circ}C$. After heat treatment, the films were crack free, and optically transparent. As a result, we demonstrated a PZT film with a PVP molar ratio of 0.5, which has a permittivity of 734, a dielectric loss of 0.042, a $P_r$ of 40.5 ${\mu}C/cm^2$ and an $E_c$ of 156 kV/cm.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.2119_2120
• /
• 2009

전압을 인가하였을 때 전계방향에 의해 가역적으로 색이 변화하는 현상을 전기변색(electrochromism)이라고 한다. 이러한 전기채색현상을 보이는 물질을 전기채색물질(electrochromism materials)이라고 하며, 전기채색 물질에 의한 소자를 전기채색소자(electrochromism device : ECD)라고 한다. 전기채색현상은 투과율(transmittance), 반사율(reflectance)의 가역적이며 가시적인 변화이고, 전기화학적인 산화환원 반응과 관련이 있다. 따라서 본 연구에서는 Titanate nanotube(TNT)를 제조하고 전기변색소자(ECD)에 응용하였다. SEM, XRD, UV-Vis등을 이용하여 재료학적 분석을 시행하였으며, 전기화학적 테스트로 cyclic voltammetry를 측정 하였다. 그 결과 TNT 분말은 직경 약 20~30 nm, 길이 약 500~600 nm 의 입자형상을 나타내었으며, X-선 회절시험결과 $H_2Ti_2O_5{\cdot}H_2O$의 층상구조를 나타내었다. 제조된 막은 FTO glass 위에 PEI/(TNT/TBAOH)$_{n-1}$/PDDA의 순으로 코팅되었다. 전기화학적 테스트를 위하여 2전극 시스템을 제작하였으며, 여러 종류의 액체 전해질을 제작하여 cycle voltammetry를 시행하였다. 그 결과, 각각의 전해질에서 "-"영역의 산화환원전위 피크가 뚜렷하게 나타났으며, 짙은 갈색으로의 채색현상을 나타냈다. 본 연구의 결과로서 TNT 박막을 이용한 ECD은 광조절 유리로서 뿐만 아니라, 여러 전기채색 디바이스에 응용될 것으로 사료된다.

• KSTLE International Journal
• /
• v.4 no.2
• /
• pp.60-65
• /
• 2003

Tribological properties of novolac resin composites containing particulate barite (BaSO$_4$) or potassium titanate (K$_2$Oㆍ6(TiO$_2$))whiskers (two typical space fillers for commercial automotive brake linings) were investigated. The emphasis of the current investigation was given to the effect of the two fillers on the propensity of the stick-slip phenomena and formation of stable rubbing surface. A block-on-disk type tribometer was used for friction assessment. Results showed that the BaSO$_4$-filled composite produced large friction force oscillations at slow sliding speeds and created severe damage on the gray iron counter surface. On the other hand, the composite with $K_2$Oㆍ6(TiO$_2$) whiskers formed a stable rubbing surface and showed smooth sliding behavior without large friction force fluctuation. The microscopic observation of the rubbing surface revealed that the $K_2$Oㆍ6(TiO$_2$)whiskers played a key role in the formation of stable rubbing surface and smooth sliding behavior by effectively reinforcing the resin.

• Journal of the Korean Ceramic Society
• /
• v.39 no.7
• /
• pp.642-648
• /
• 2002

Barium Titanate(BaTiO$_3$) nanoparticles were prepared at 22$0^{\circ}C$ through glycothermal process by using barium hydroxide and amorphous titanium hydrous gel as precursor and 1,4-butanediol and distilled water as solvent. It is demonstrated that the size of BaTiO$_3$ particles can be controlled by reaction conditions such as various content of 1,4-butanediol/distilled water volume ratio. This processing method can fabricate BaTiO$_3$ powders, which have a narrow distribution and exhibit good dispersion. The particle size of BaTiO$_3$ powders obtained by glycothermal process were about 50 nm to 200 nm on the condition that reaction temperature was 22$0^{\circ}C$ and holding time was 24 h.

• Bulletin of the Korean Chemical Society
• /
• v.25 no.9
• /
• pp.1341-1345
• /
• 2004

We developed a novel synthesis strategy of titania nanowire arrays by employing simple hydrothermal reaction and ion-exchange reaction techniques. Hydrothermal reactions of metallic titanium powder with $H_2O_2$ in a 10 M NaOH solution produced a new sodium titanate compound, $Na_2Ti_6O_{13}{\cdot}xH_2O$ (x~4.2), as arrays of nanowires of lengths up to 1 mm. Acid-treatment followed by calcination of this material produced arrays of highly crystalline anatase nanowires as evidenced by x-ray diffraction, Raman spectroscopy, and transmission electron microscopy studies. In both cases of sodium titanate and anatase, the nanowires have exceptionally large aspect ratios of 10,000 or higher, and they form arrays over a large area of $1.5 {\times} 3 cm^2$. Observations on the reaction products with varied conditions indicate that the array formation requires simultaneously controlled formation and crystal growth rates of the $Na_2Ti_6O_{13}{\cdot}xH_2O$ phase.

• Transactions on Electrical and Electronic Materials
• /
• v.18 no.3
• /
• pp.163-168
• /
• 2017

The aim of the current research was to develop and present an effective methodology for simulating and analyzing the electrical and structural properties of piezoelectric material. The finite element method has been used to make precise numerical models when dielectric, piezoelectric and mechanical properties are known. The static and dynamic responses of circular ring-shaped barium titanate piezoelectric material have been investigated using the commercially available finite element software ABAQUS/CAE. To gain insight into the crystal morphology and to evaluate the purity of the material, a microscopic study was conducted using a scanning electron microscope and energy dispersive x-ray analysis. It is found that the maximum electrical potential of 6.43 V is obtained at a resonance frequency of 35 Hz by increasing the vibrating load. The results were then compared with the experimentally predicted data and the results agreed with each other.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.171-171
• /
• 2007

Dysprosium-doped bismuth titanate (BDT) thin films were successfully deposited on Pt(111)/Ti/$SiO_2$/Si(100) substrates by liquid delivery MOCVD process and their structural and ferroelectric properties were characterized. Fabricated BDT thin films were found to be random orientations, which were confirmed by X-ray diffraction experiment and scanning electron microscope analysis. The crystallinity of the BDT films was improved and the average grain size increased as the crystallization temperature increased from 600 to $720^{\circ}C$ at an interval of $40^{\circ}C$. The BDT thin film annealed at $720^{\circ}C$ showed a large remanent polarization (2Pr) of $52.27\;{\mu}C/cm^2$ at an applied voltage of 5V. The BDT thin film exhibits a good fatigue resistance up to $1.0{\times}10^{11}$ switching cycles at a frequency of 1 MHz with applied pulse of ${\pm}5\;V$. These results indicate that the randomly oriented BDT thin film is a promising candidate among ferroelectric materials useti비 in lead-free nonvolatile ferroelectric random access memory applications.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.641-644
• /
• 2005

The aim of this research is to evaluate the relationship between the total effective moment $(M^E)$ and Bemoulli-Euler bending moment (M) when the ply orientations of UD CFRP in Piezoelectric Zirconate Titanate Composite Actuator (PZTCA) are changed. The obtained results as follows. Firstly, as the performance test results by the CFRP ply orientation, the performance of [0] and [90] were stable. However, while the performance of [+45] was suddenly decreased after 5 hours. Secondly, the change of $M^E$ by the CFRP ply orientation was evaluated. As the CFRP ply orientation was increased from [0] to [+60], the $M^E$ were gradually decreased. However, they became a little bit increased from [+60] to [90]. Finally, after the change of M by the CFRP ply orientation was evaluated, it was found that $M^E=2.2M$ was valid for just [0] and that there was a relationship between $M^E$ and M according to the ply orientation.

• Biomaterials and Biomechanics in Bioengineering
• /
• v.4 no.1
• /
• pp.33-44
• /
• 2019

This paper presents a novel structural composition for artificial bone scaffolds with an appropriate biocompatibility and biodegradability capability. To achieve this aim, carbon nanotubes, due to their prominent mechanical properties, high biocompatibility with the body and its structural similarities with the natural bone structure are selected in component of the artificial bone structure. Also, according to the piezoelectric properties of natural bone tissue, the barium titanate, which is one of the biocompatible material with body and has piezoelectric property, is used to create self-healing ability. Furthermore, due to the fact that, most of the bone tissue is consists of hydroxyapatite, this material is also added to the artificial bone structure. Finally, polycaprolactone is used in synthetic bone composition as a proper substrate for bone growth and repair. To demonstrate, performance of the presented composition, the mechanical behaviour of the bone scaffold is simulated using ANSYS Workbench software and three dimensional finite element modelling. The obtained results are compared with mechanical behaviour of the natural bone and the previous bone scaffold compositions. The results indicated that, the modulus of elasticity, strength and toughness of the proposed composition of bone scaffold is very close to the natural bone behaviour with respect to the previous bone scaffold compositions and this composition can be employed as an appropriate replacement for bone implants.