• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.33-34
• /
• 2008

Barium titanate (BaTiO3) is one of the most important dielectric materials for the electronic devices, such as MLCC (Multilayer Ceramic Capacitor). The thickness of the dielectric thin film in MLCC has become thinner and reached about 0.8 ${\mu}m$. Further down sizing is required for the higher performance. For this reason, we should take into account for the size effect of Barium titanate powders. In this study, we demonstrated that size effect for BaTiO3 (0.2 ~ 0.5 ${\mu}m$, hydrothermal BT) could be estimates by using dielectric properties analysis together with the powder properties.

• 한국세라믹학회지
• /
• 제28권11호
• /
• pp.859-864
• /
• 1991

High quality lead titanate thin films were fabricated by spin coating on a silicon substrate. The resulting dried gel layers were uniform in thickness through 2$\times$2 $\textrm{cm}^2$ area, and polycrystalline perovskite structures developed almost crack free with a heat treatment above 50$0^{\circ}C$ in films with thickness above 360 nm. Metastable pyrochlore structures were observed in films with thickness of 160 nm when heat treated at 500 and $600^{\circ}C$, but these structure did not appear in films with thickness of 360 nm. The thickness dependence in crystal structure of films was studied. by varying the substrate condition and analyzing the interface between the film and substrate. In native oxide films on silicon stbstrates, amorphous dried gel layers were heterogeneously nucleated. Metastable cubic pyrochlore structure could be crystallized in amorphous native oxide.

• 한국세라믹학회지
• /
• 제28권11호
• /
• pp.892-896
• /
• 1991

The cyrstallization behavior of lead titanate powders prepared by sol-gel and coprecipitation techniques was investigated. The lead titanate precursors were derived from a mixed solution of lead nitrate and titanium tetrachloride at 4$0^{\circ}C$ to 43$^{\circ}C$ and pH of 9.00 to 9.75. The X-ray diffraction patterns of the dried gel and coprecipitated powders showed it to be amorphous. DTA runs of the powders indicated crystallization to occur at 475~48$0^{\circ}C$. However, the amorphous powders were partially crystallized at 400~45$0^{\circ}C$ with sufficient annealing time. The room temperature Raman spectra from heat-treated powders changed continuously from amorphous to crystalline state with increasing heat-treating temperature. By annealing coprecipitated powders, a dramatic change in the Raman spectra due to the structural relaxation as the annealing temperatures increased, was clearly visible. i.e., coprecipitated, gel, and crystalline structure, in turn.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2014년도 추계학술대회 논문집
• /
• pp.69-71
• /
• 2014

MLCCs are used broadly in electronic industry like smart phone and TV. Although they are fabricated in small size and have high capacitance, there are acoustic noise problems to reduce comfort of user. Acoustic noise results from linear piezoelectricity and nonlinear electrostriction of $BaTiO_3$ in MLCC and there are some researches on MLCC vibration under AC electric field. When only AC electric field without DC bias is applied to MLCC, fundamental frequency response is affected by piezoelectricity and second-harmonic frequency response shows electrostrictive vibration. In this study we get vibration shape of MLCC under AC electric field for each frequency and analysis on the mechanism of MLCC vibration affected by piezoelectricity and electrostriction.

• The Korean Journal of Ceramics
• /
• 제3권3호
• /
• pp.195-198
• /
• 1997

Post-firing process of electronic ceramic, such as electroding and encapsultion with resin, often causes damage by thermal shock. The thermal shock behavior of $BaTiO_3$ ceramics was investigated by the down-quench test, where the relative strength retained is determined after the sample is quenched from an elevated temperature into a fixed temperature bath. The critical temperature drop, $\DeltaTc$, was evaluated for three kinds of sintered $BaTiO_3$ ceramics, which were formed by extrustioin, uniaxial pressing using granules, and uniaxial pressing using powders. A drastic loss in strength caused by microcracking was observed for the specimens quenched with $\DeltaT\geq150^{\circ}C$. This concentp can be adopted as a method of the quality control by monitoring the sudden drop of the strength of capacitor products after each exposure to heat.

• 한국해양공학회지
• /
• 제14권1호
• /
• pp.37-43
• /
• 2000

$PbTiO_3$ was prepared by addition of lead-tltanium mixed aqueous solution to an ethanol solution of oxalic acid. The influence of various ripening factors was invesigated. On the basis of the results in the mono-component system we studied the foramtion of $PbTiO_3$ phase with various ripening conditions. The $PbTiO_3$ phase formation was accelerated with the ripening time temperature and ultrasonic irradiation.

• The Korean Journal of Ceramics
• /
• 제6권4호
• /
• pp.385-389
• /
• 2000

Residual stresses in epitaxial films were measured by X-ray diffraction method. Lattice strains of the (hkl) planes measured along particular Ψ-angles were converted to the in-plane stress according to the equation of stress-strain tensor conversion. Residual tensile stresses were observed in epitaxial PbTiO$_3$ films deposited on (100) SrTiO$_3$ substrate. Tensile stresses approximately 0.9 GPa were measured in Pb-rich films, while it increased to approximately 2.0 GPa with the decreasing of Pb content in the case of Pb-poor films, which ascribed to the formation of lead and oxygen vacancies (expressed as x in Pb$_1-x$TiO$_3-x$).

• 한국세라믹학회지
• /
• 제39권4호
• /
• pp.336-340
• /
• 2002

Pure and nano-sized $TiO_2$ and $CaTiO_3$ powders were fabricated by a polymeric steric entrapment route and planetary milling process. An ethylene glycol was used as a polymeric carrier for the preparation of organic-inorganic precursors. Titanium isopropoxide and calcium nitrate were dissolved in liquid-type ethylene glycol without any precipitation. At the optimum amount of the polymer, the metal cations were dispersed in solution and a homogeneous polymeric network was formed. The dried precursor ceramic gels were turned to porous powders through calcination process. The porous powders were crystallized at low temperatures and the crystalline powders were planetary milled to nano size.

• 한국세라믹학회지
• /
• 제43권11호
• /
• pp.673-679
• /
• 2006

The discovery of ferroelectric barium titanate (BaTiO$_3$) in 1942 began the present era of dielectrics-based electronic ceramics. Ferroelectric barium titanate has a high dielectric constant and after the recognition of BaTiO$_3$ as a new ferroelectric compound, various attractive electrical properties have been extensively studied and reported. Since then, pioneering work on valence-compensated semiconduction led to the discovery of the positive temperature coefficient (PTC) of the resistance effect found in doped BaTiO$_3$. Significant progress has since followed with respect to understanding the PTC phenomena, advancing materials capabilities, and developing devices for sensor and switching applications. In this paper, the theoretical aspects of the various PTC models are discussed and the future trends of practical applications for PTC devices are briefly mentioned.

• 한국세라믹학회지
• /
• 제24권1호
• /
• pp.41-46
• /
• 1987

When barium titanate was synthesized in soild-solid reaction the abnormal expansion occurred from 900$^{\circ}C$ to 1100$^{\circ}C$. The equi-molecular mixture of BaCO3 and TiO2 was sintered from 800$^{\circ}C$ to 1300$^{\circ}C$ on the condition of air, vacuum and CO2 atmosphere. After that the specimens were tested closely with XRD, Dilatometer, SEM and EDS. The result indicated that; 1. The crystal phase which was concerned with expansion of BaTiO3 was Ba2TiO4 as the intermediate crystal phase. 2. The formation of Ba2TiO4 was affected by the firing atmosphere. 3. The expansion occurred when BaTiO3 changed to Ba2TiO4 and pore also expanded by the expansion of BaTiO3 body just as the model of expansion.