• Journal of Welding and Joining
• /
• v.20 no.4
• /
• pp.498-504
• /
• 2002

Fluxless flip chip bonding process using plasma treatment instead of flux was investigated. The effect of plasma process parameters on tin-oxide etching characteristics were estimated with Auger depth profile analysis. The die shear test was performed to evaluate the adhesion strength of the flip chip bonded after plasma treatment. The thickness of oxide layer on tin surface was reduced after Ar+H2 plasma treatment. The addition of H2 improved the oxide etching characteristics by plasma. The die shear strength of the plasma-treated Sn-Pb solder flip chip was higher than that of non-treated one but lower than that of fluxed one. The difference of the strength between plasma-treated specimen and non-treated one increased with increase in bonding temperature. The plasma-treated flip chip fractured at solder/TSM interface at low bonding temperature while the fracture occurred at solder/UBM interface at higher bonding temperature.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.213-213
• /
• 2000

A sensor system which can measure the transmittance of ITO(Indium Tin Oxide) layed glass is proposed. The sensor system includes a single wavelength laser beam source, photo diodes and electronic circuit processing sensor signal. The wavelength of laser is 543.5 m, this is most sensitive wavelength to photopic and scotopic vision. We applied the sensor to measure transmittance of ITO layer on general manufacturing environment and verified the effectiveness of sensor through experimental measurement.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.1464-1465
• /
• 2008

In this paper, we compared the mechanical characteristics between LTCC-based RF MEMS packaging structures fabricated using two different types of bonding materials; BCB and gold-tin. The BCB-based packages showed an average shear strength of 32.1 MPa and helium leak rate of $1.76{\times}10^{-8}atm{\cdot}cc/sec$ for a cavity volume of $0.45\times10^{-3}cc$, while the packages bonded by gold-tin layer (80 wt.% gold, 20 wt.% tin) showed an average shear strength of 42.70 MPa and helium leak rate $1.38{\times}10^{-8}atm{\cdot}cc/sec$ for a cavity volume of $1.21{\times}10^{-3}cc$.

• Korean Journal of Optics and Photonics
• /
• v.11 no.3
• /
• pp.152-157
• /
• 2000

Post-deposition vacuum annealing effects in electron-bearn-evaporated indium tin oxide (ITO) films have been investigated by the change of transmittance, sheet resistance and crystalline structure with annealing temperature ( $200-335^{\circ}C$) and oxygen partial pressure ($1\times^10^{-5}-1$\times10^{-4} torr$) in air and vacuum. The sarnples were polycrystalline films with a preferred orientation in the (222) plan. High quality films with sheet resistance as low as 62 Q/O and transmittance over 99% (absentee layer at 500 nm) have been obtained by suitably controlling the vacuum annealing pararneters.neters.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.1496-1499
• /
• 2009

A diode-pumped Nd:$YVO_4$ laser was used to obtain indium tin oxide (ITO) patterns on glass substrate with various overlapping rates. The results showed that the overlapping rate of laser beam influences on the edge structure of ITO pattern and the surface roughness of ablated groove bottom. At a laser repetition rate of 40 kHz, the optimized condition of overlapping rate was 75 %.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.170-170
• /
• 2010

Thin-film transistors (TFT) have become the key components of electronic and optoelectronic devices. Most conventional thin-film field-effect transistors in display applications use an amorphous or polycrystal Si:H layer as the channel. This silicon layers are opaque in the visible range and severely restrict the amount of light detected by the observer due to its bandgap energy smaller than the visible light. Therefore, Si:H TFT devices reduce the efficiency of light transmittance and brightness. One method to increase the efficiency is to use the transparent oxides for the channel, electrode, and gate insulator. The development of transparent oxides for the components of thin-film field-effect transistors and the room-temperature fabrication with low voltage operations of the devices can offer the flexibility in designing the devices and contribute to the progress of next generation display technologies based on transparent displays and flexible displays. In this thesis, I report on the dc performance of transparent thin-film transistors using amorphous indium tin zinc oxides for an active layer. $SiO_2$ was employed as the gate dielectric oxide. The amorphous indium tin zinc oxides were deposited by RF magnetron sputtering. The carrier concentration of amorphous indium tin zinc oxides was controlled by oxygen pressure in the sputtering ambient. Devices are realized that display a threshold voltage of 4.17V and an on/off ration of ${\sim}10^9$ operated as an n-type enhancement mode with saturation mobility with $15.8\;cm^2/Vs$. In conclusion, the fabrication and characterization of thin-film transistors using amorphous indium tin zinc oxides for an active layer were reported. The devices were fabricated at room temperature by RF magnetron sputtering. The operation of the devices was an n-type enhancement mode with good saturation characteristics.

• The Journal of Korean Academy of Prosthodontics
• /
• v.27 no.1
• /
• pp.143-179
• /
• 1989

To observe the bonding behavior of palladium-based alloys to porcelain; 1. Pd-Co binary alloy with the higher cobalt content, 2. Pd-Co binary alloy with the lower cobalt content, 3. Pd-Ag-Sn ternary alloy, 4. Pd-Ag binary alloy, 5. Pd-Cu-Au ternary alloy and 6. Pd-Cu binary alloy were made as 6 groups of experimental alloys. Each group of alloy was divided into 4 sub-groups such as one sub-group that was not degassed and three sub-groups that degassed for 5 minutes, 10 minutes and 15 minutes. On each specimen, weight changes after degassing, morphological changes of oxide layer by changing the degassing time, compositional changes at metal-ceramic interface and bond strength of metal-ceramic measured with planar shear test were observed and compared. The results of the present study allow the following conclusions to be drawn: 1. The alloy showing the greatest bond strength was Pd-Cu alloy without gold and bond strength was decreased by alloying gold to them. 2. Although Pd-Co alloy showed the most prominent oxidation behavior, bond strength of them to porcelain was not greatly high by the formation of porosities at metal-ceramic interfaces. 3. Likewise tin, cobalt formed the peaks on line profiles at metal-ceramic interface, however copper did not exhibit such peaks on line profiles. 4. Mainly, oxide layer on Pd-Co alloy was composed with cobalt, and for Pd-Co alloy with higher cobalt content the rise of bond strength was not significant by increased degassing time. 5. On Pd-Ag alloy not containing tin, during degassing for 15 minutes silver content was increased at metal-ceramic interface. 6. As an oxidized element, tin formed the oxide layers that widen their area by increasing the degassing time, while cobalt and copper showed the morphological changes of particle or crystal on oxide layer.

• Korean Journal of Materials Research
• /
• v.18 no.10
• /
• pp.521-528
• /
• 2008

We present the structural, optical, and electrical properties of amorphous silicon suboxide (a-$SiO_x$) films grown on indium tin oxide glass substrates with a radio frequency magnetron technique from a polycrystalline silicon oxide target using ambient Ar. For different substrate-target distances (d = 8 cm and 10 cm), the deposition temperature effects were systematically studied. For d = 8cm, oxygen content in a-$SiO_x$ decreased with dissociation of oxygen onto the silicon oxide matrix; temperature increased due to enlargement of kinetic energy. For d = 10 cm, however, the oxygen content had a minimum between $150^{\circ}\;and\;200^{\circ}$. Using simple optical measurements, we can predict a preferred orientation of liquid crystal molecules on a-$SiO_x$ thin film. At higher oxygen content (x > 1.6), liquid crystal molecules on an inorganic liquid crystal alignment layer of a-$SiO_x$ showed homogeneous alignment; however, in the lower case (x < 1.6), liquid crystals showed homeotropic alignment.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.259-259
• /
• 2015

Single crystalline indium-tin-oxide (ITO) nanowires (NWs) were grown by sputtering method. A thin Ni film of 5 nm was deposited before ITO sputtering. Thermal treatment forms Ni nanoparticles, which act as templates to diffuse Ni into the sputtered ITO layer to grow single crystalline ITO NWs. This Ni diffusion through an ITO NW was investigated by transmission electron microscope to observe the Ni-tip sitting on a single crystalline ITO NW. Meanwhile, a single crystalline ITO structure was found at bottom and body part of a single ITO NW without remaining of Ni atoms. This indicates the Ni atoms diffuse through the oxygen vacancies of ITO structure. Rapid thermal process (RTP) applied to generate an initial stage of a formation of Ni nanoparticles with variation in time periods to demonstrate the existence of an optimum condition to initiate ITO NW growth. Modulation in ITO sputtering condition was applied to verify the ITO NW growth or the ITO film growth. The Ni-assisted grown ITO layer has an improved electrical conductivity while maintaining a similar transmittance value to that of a single ITO layer. Electrically conductive and optically transparent nanowire-coated surface morphology would provide a great opportunity for various photoelectric devices.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.1
• /
• pp.130-133
• /
• 2010

Although many structures based on $SnO_2$ nanowires have been demonstrated, there is a limitation towards practical application due to the unwanted contact potential between the metal electrode and the $SnO_2$ nanowire. This is mostly due to the presence of the native oxide layer that acts as an insulator between the metal contact and the nanowire. In this study the contact properties between Ti/Au contacts and a single $SnO_2$ nanowire was compared to the electrical properties of a contact without the oxide layer. RIE(Reactive Ion Etching) is used to selectively remove the oxide layer from the contact area. The $SnO_2$ nanowires were synthesized by chemical vapor deposition (CVD) and dispersed on a $Si/Si_3N_4$ substrate. The Ti/Au (20nm/100nm) electrodes were formed bye-beam lithography, e-beam evaporation and a lift-off process.