• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.10
• /
• pp.79-85
• /
• 2009

The design of a 3.2 Gb/s serial link receiver in $0.18{\mu}m$ CMOS process is presented. The major factors limiting the performance of high-speed links are transmission channel bandwidth, timing uncertainty. The design uses a multi-level signaling(4-PAM) to overcome these problems. Moreover, to increase data bit-rate and lower BER, we designed this circuit by using a current mode amplifier, Current-mode Logic(CML) sampling latches. The 4-PAM receiver achieves 3.2 Gb/s and BER is less than $1.0\;{\times}\;10^{-12}$. The $0.5\;{\times}\;0.6\;mm^2$ chip consumes 49 mA at 3.2 Gb/s from a 1.8-V supply.

• Journal of Power System Engineering
• /
• v.14 no.1
• /
• pp.5-10
• /
• 2010

Both the accuracy and stability of the clock get from the GPS receiver are considered in the range of pps. And we verified the system clock stability of a micro-controller system using the pps pulse supplied by the GPS receiver. In complex system of digital processing, the rack of precise timing signal may cause the serious problem or breakdown accident. To get rid of these undesirable problems, we introduced VCXO circuit to a micro-controller system to preserve high accurate clock stability.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.1C
• /
• pp.40-44
• /
• 2010

The timing error detector(TED) employed in the closed loop type timing synchronization scheme for an MQASK all digital receiver suffers from the selfnoise-induced timing jitter. To eliminate the timing jitter a prefilter can be added in front of the TED. The prefilter method, however, degrades the stability and timing acquisition performance due to the loop delay and increases the complexity of the synchronizer. This paper proposes a polyphase filter type resampler approach to optimize the performance and architecture of the synchronizer simultaneously. The proposed scheme uses two resamplers which performs matched filtering and matched prefiltering so that the loop delay is minimized with minimal hardware resources. Simulation results showed an excellent acquisition performance with reduced timing jitter.

• Journal of Positioning, Navigation, and Timing
• /
• v.5 no.1
• /
• pp.11-20
• /
• 2016

In this paper, a system that can collect GPS L1 C/A, GLONASS G1, and BDS B1I signals with single front-end receiver was implemented using a universal software radio peripheral (USRP) and its performance was verified. To acquire the global navigation satellite system signals, hardware was configured using USRP, antenna, external low-noise amplifier, and external oscillator. In addition, a value of optimum local oscillator frequency was selected to sample signals from three systems with L1-band with a low sampling rate as much as possible. The comparison result of C/N0 between the signal collection system using the proposed method and commercial receiver using double front-end showed that the proposed system had 0.7 ~ 0.8dB higher than that of commercial receiver for GPS L1 C/A signals and 1 ~ 2 dB lower than that of commercial receiver for GLONASS G1 and BDS B1I. Through the above results, it was verified that signals collected using the three systems with a single USRP had no significant error with that of commercial receiver. In the future, it is expected that the proposed system will be combined with software-defined radio (SDR) and advanced to a receiver that has a re-configuration channel.

• Journal of Astronomy and Space Sciences
• /
• v.17 no.1
• /
• pp.117-122
• /
• 2000

The KOMPSAT(Korea Multi-Purpose SATellite) has two optical imaging instruments called EOC(Electro-Optical Camera) and OSMI (Ocean Scanning Multispectral Imager). The image data of these instruments are transmitted to ground station and restored correctly after post-processing with the telemetry data transfeered from KOMPSAT spacecraft. The major timing information of the KOMPSAT is OBT (On-Board Time) which is formatted by the on-board computer of the spacecraft, based on 1Hz sync. pulse coming from the GPS receiver involved. The OBT is transmitted to ground station with the house-keeping telemetry data of the spacecraft while it is distributed to the instruments via 1553B data bus for synchronization during imaging and formatting. The timing information contained in the spacecraft telemetry data would have direct relation to the image data of the instruments, which should be well explained to get a more accurate image. This paper addresses the timing analysis of the KOMPSAT spacecraft and instruments, including the gyro data timing analysis for the correct restoration of the EOC and OSMI image data at ground station.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.22 no.3
• /
• pp.539-546
• /
• 1997

In this paper, we proposed a new mehtod to analyze the performance degradation by timing jitters in the APD (avalanche photodiode) receivers of intensity modulation/direct detection digital optical communication systems where raised cosine pulse-shaping filters are used to reduce the effect of noise while minimizing intersymbol interferences. The proposed analytical method is an extension of an analytical method we have already developed for pin diode receivers, and incorporates the effects of APD's multiplication factor and resulting shot noise. Using the proposed analytical method, we derive an approximated power penalty due to timing jitters based on an assumption of Gaussian distribution for timing jitters, and compare with that of the conventional analytical method. The results obtained from the proposed analytical method show that conventional analytical methods underestimate the influence of timing jitters on the reciver performance. The results also show that APD's multiplication factor which optimizes receiver sensitivity is smaller than that obtained by the conventional analytical method.

• Journal of Positioning, Navigation, and Timing
• /
• v.2 no.1
• /
• pp.75-80
• /
• 2013

This article presents the design of long range navigation (LORAN)-disciplined oscillator (LDO), employing the timing information of the LORAN system, which was developed as a backup system that corrects the vulnerability of the global positioning system (GPS)-based timing information utilization. The LDO designed on the basis of hardware generates a timing source synchronized with reference to the timing information of the LORAN-C receiver. As for the LDO-based timing information measurement, the Kalman filter was applied to estimate the measurement of which variance was minimized so that the stability performance could be improved. The oven-controlled crystal oscillator (OCXO) was employed as the local oscillator of the LDO. The controller was operated by digital proportional-integral-derivative (PID) controlling method. The LDO performance evaluation environment that takes into account the additional secondary factor (ASF) of the LORAN signals allows for the relative ASF observation and data collection using the coordinated universal time (UTC). The collected observation data are used to analyze the effect of ASF on propagation delay. The LDO stability performance was presented by the results of the LDO frequency measurements from which the ASF was excluded.

• Journal of Positioning, Navigation, and Timing
• /
• v.6 no.4
• /
• pp.135-140
• /
• 2017

This paper proposes a signal merging algorithm to increase the signal-to-noise ratio (SNR) of a GPS correlator output to estimate the roll angle of a rotating vehicle in a weak GPS signal environment. Rotation Locked Loop (RLL) algorithm is used to estimate a roll angle using the characteristics that the power of the GPS signal measured at the receiver of a rotating vehicle varies periodically. First, delay times are calculated to synchronize GPS signals using satellites' and receiver's positions and the rotation frequency of a vehicle, and then correlator outputs are delayed in time and merged with each other, resulting in the increase of an SNR in a correlator output. Finally, simulations are conducted and the performance of the proposed algorithm is validated.

• Journal of Positioning, Navigation, and Timing
• /
• v.7 no.3
• /
• pp.113-125
• /
• 2018

Since the global positioning system receivers on the surface of the Earth use satellite signals sent from a remote distance and the intensity of received signals is weak, they are vulnerable to jamming. This paper implements a vector-tracking loop (VTL)-based global navigation satellite system (GNSS) receiver algorithm as an anti-jamming technique and compares the performance of VTL-based receivers with that of scalar-tracking loop (STL) that is used in general GNSS receivers at various jamming environments and a vehicle's dynamics. The simulation results shows that VTL is more robust against jamming than STL in all operating environments.

• Journal of Positioning, Navigation, and Timing
• /
• v.7 no.3
• /
• pp.175-181
• /
• 2018

The use of dual-frequency measurements from the Global Navigation Satellite System (GNSS) enables us to observe precise ionospheric total electron content (TEC). Currently, many GNSS reference stations in South Korea provide both GPS and GLONASS data. In the present study, we estimated the grid-based TEC values and relative receiver differential code biases (DCB) from a GNSS network operated by the Korea Astronomy and Space Science Institute. In addition, we compared the diurnal variations in a TEC time series from solutions of the GPS only, the GLONASS only, and combined GPS/GLONASS processing. A significant difference between the GPS only TEC and combined GPS/GLONASS TEC at a specific grid point over South Korea appeared near the solar terminator. It is noted that GLONASS measurements can contribute to observing a variation in ionospheric TEC over high latitude regions.