• ETRI Journal
• /
• v.30 no.2
• /
• pp.282-289
• /
• 2008

We propose a new mini-slot transmission scheme for a passive optical network (PON) in which each customer can be switched either to access mode or to internetworking mode dynamically. In this paper, we present the system implementation (called LAN-PON) as well as the performance of the proposed transmission scheme to illustrate its feasibility and benefits. A mini-slot scheme can rapidly reduce the queuing delay, which increases due to the flooding of the deflected packets in a deflection scheme. We evaluate the impact of mode switching time on the bandwidth gain (throughput) and delay of local area network (LAN) traffic in the LAN-PON with a mini-slot scheme. We also analyze a theoretical delay model of the proposed scheme. The simulation results demonstrate that switching time has an impact on LAN performance, and the average packet delay of the proposed scheme is significantly improved compared to that of the deflection scheme.

• Journal of the Korean Data and Information Science Society
• /
• v.16 no.3
• /
• pp.639-650
• /
• 2005

Theoretical and numerical comparison have shown that variable sampling interval (VSI) charts are substantially more efficient than fixed sampling interval(FSI) charts in term of ATS(average time to signal). But the frequency of switching between different sampling intervals is a complicating factor in VSI procedures. VSI EWMA charts for monitoring mean vector of related qualify characteristics are investigated. To compare the efficiencies of the proposed charts, the performances are evaluated for matched FSI and VSI charts in terms of average time to signal(ATS) and average number of samples to signal(ANSS). For the switching behavior of the proposed VSI charts, average number of switches(ANSW) are also investigated.

• Proceedings of the KIEE Conference
• /
• 1998.07f
• /
• pp.1937-1939
• /
• 1998

This paper presents a simple switching method to generate a PWM pattern mostly relevant to signle-phase three-level PWM rectifier. The adopted PWM switching pattern is performed in a manner similar to the space vector PWM method, which is popularly used in the three-phase rectifier and inverter. A set of possible voltages has been selected so that an equation with a time integral considered within a sampling period should be satisfied every sampling time. The simulation result shows that the proposed control scheme is good in some performance criteria such as unity power factor, low harmonic distortion of input current, dynamic response and voltage balancing of two series-connected DC capacitors.

• Proceedings of the KIEE Conference
• /
• 1994.07a
• /
• pp.509-511
• /
• 1994

Cycloconverters can be classified into two types by the main circuit configuration. One is the non- circulating current type required the dead time the other is circulating current type which has the circulating current reactors. The switching devices were highly stressed by the load voltages during dead time on non-circulating current type operation and the circulating currents on circulating current type operation. The overcome those problems, this paper proposes the switching patterns for the partial and the non circulation current type. The PWM methods, which are saw wave comparing method and load current integrating value comparing method, are presented.

• Proceedings of the KIPE Conference
• /
• 2001.12a
• /
• pp.164-165
• /
• 2001

An IGBT driver for serially connected pulse switching IGBTS was contructed and tested. The IGBT driver has ten output pulses with 1 ${\mu}ysec$ pulse width Its pulse repetition-rate can adjusted from 0 to 20 kHz. The output pulses was insulated from 10 kV high voltage by a pulse transformer. Their voltage amplitude are 18 V, voltage rising time 250 nsec., and voltage falling time 200 nsec when IGBT gates with 12 nF input capacitance are connected.

• Proceedings of the KIEE Conference
• /
• 1992.07b
• /
• pp.1129-1132
• /
• 1992

This paper proposes a high frequency resonant inverter consisting of equivalent half bridge model using MOSFET. In this paper time-sharing control method is applied. as a result the output frequency is two times as high as switching frequency of device, and average current of device is incresed because of decreasing switching loss.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.9 no.5
• /
• pp.51-56
• /
• 1995

The transistors of single phase 3 level PWM Inverter compose output power transistors and neutral point clamping transistors, which are NPN transistors. Waveforms of driving signals for this are PWM waves for power transistors and period operating waves for neutral point clamping transistors, which signals made W-type modulation from rectangular and sine wave. The output power transistors operate at ON-time complementary and neutral point clamping transistors operate at OFF-time complementary respectively. Therefore, each transistors operate in half period at parallel. Characteristics of this inverter circuit is parallel switching method about series switching method of general inverter. As modulation of 3 level drive signals made from full-wave rectifier of sine wave and rectangular wave, which are level wave about 3 level of complementary transistor inverter. So, this circuit composed complementary operation inverter of NPN transistors only compare with PNP-NPN complementary inverter, which have high power 3 level inverter of complementary operation.

• Proceedings of the KIEE Conference
• /
• 2007.10c
• /
• pp.135-137
• /
• 2007

In this paper, an advanced torque control scheme of SRM using DITC(Direct Instantaneous Torque Control) and PWM(pulse width modulation) is presented. Different from conventional DITC method, proposed method uses one or two switching modes at every sampling time, instead of only one switching mode. The duty ratio of the phase switch is regulated according to the torque error and simple control rules of DITC. Moreover the sampling time of control can be extended, which allows implementation on low cost microcontrollers. The proposed control method is verified by the simulations and experimental results.

• Proceedings of the KIEE Conference
• /
• 2000.07a
• /
• pp.233-235
• /
• 2000

SVC(Static Var Compensator) is commonly installed with conventional mechanically switched existing reactor or capacitor banks for wide range voltage control. The frequencies of switching of external banks have a great impact on the quality of voltage, but is limited since the life time of the external banks depends severely on the number of switching. So it is a complete multi-objective nonlinear optimization problem with conflicting objectives. This paper presents a method to determine the optimal coordination of SVC and external banks using genetic algorithm based on the multi-objective criteria. Optimal dead band and delay time of external banks is sought for reliable and efficient operation

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.253-256
• /
• 1996

In this paper, A new time-varying sliding surface design using eigenvalue locus is proposed to achieve fast and robust in a class of high-order uncertain dynamic system. A moving sliding surface(MSS) was proposed earlier for the second-order variable structure control systems(VSCS). This methodology led to fast and robust control responses of the second-order VSCS. However, the moving algorithm of the MSS was too complicated to be employed the high-order VSCS. To resolve this problem, we propose a new moving algorithm that switching surface moves such that the eigenvalues of equivalent system in the sliding mode have a predetermined locus. Using the proposed surface fast and robust behaviors are accomplished. The problem of chattering can be eliminated by using a boundary layer of switching surface. The efficiency of proposed algorithm is illustrated by an application to four-order workbench.