• Design & Manufacturing
• /
• v.2 no.5
• /
• pp.30-33
• /
• 2008

Injection Molding is the most effective process for mass production of plastic parts. The injection molding process is composed with several steps such as Filling, Packing, Holding, Cooling, Ejecting. Among them, filling and packing process should be considered carefully to improve accuracy of dimension, surface quality of plastic parts. Usually the quality above-mentioned is managed with weight of part after molding on the field. In this paper, a series of experiment for molding automotive front bumper was conducted with cavitity temperature sensor to optimize switch-over time(V-P switching), hot runner vale gate sequence time during filling and packing step for the purpose of uniform quality, weight at every molding. As a result, it was found that it is effective method to use temperature sensor in injection molding for quality control of plastic molding.

• Journal of The Institute of Information and Telecommunication Facilities Engineering
• /
• v.6 no.3
• /
• pp.1-7
• /
• 2007

In this paper, we propose a new prioritized Optical Burst Switching (OBS) protocol based on a hop count, which can provide efficient utilization in optical networks. Under several legacy schemes, a switch drops the burst with the shortest time regardless of its traversed hop count. As a result, a dropped burst that have been traversed many hops might cause increased bandwidth waste compared to one that has traversed a few hops. To improve this problem, we propose the Just Enough Time (JET) with a hop counting scheme which can reduce the wasted bandwidth by prioritizing the burst traversed many hops over others. From the simulation result, it is preyed, we show that the proposed scheme has advantages against legacy schemes in terms of the burst blocking probability and the link utilization.

• Proceedings of the KIEE Conference
• /
• 1990.11a
• /
• pp.309-313
• /
• 1990

Pulse width modulation using discontinuous conduction modes are applied to a full-bridge series resonant converter to regulate the output from no load to full load with low switching loss and a narrow range of frequency variation. Finally, a simple nonlinear discrete-time dynamic model for this proposed converter is derived using approximation. This discrete time model is linearized and a general input - output transfer function for the propelled converter is derived.

• Proceedings of the KIEE Conference
• /
• 2006.04b
• /
• pp.267-269
• /
• 2006

In this paper, a new single phase voltage sag/swell compensator using direct power conversion is introduced. A new compensator consists of input/output filter, series transformer and direct ac-ac converter, which is a single-phase back-to-back PWM converter without dc-link capacitors. Advantages of the proposed compensator include: simple power circuit by eliminating dc-link electrolytic capacitors and thereby, improved reliability and increased life time of the entire compensator; simple PWM strategy to compensate voltage sag/swell at the same time and reduced switching losses in the ac-ac converter. Further, the proposed scheme is able to adopt simple switch commutation method without requiring complex four-step commutation method commonly required in the direct power conversion. Simulation results are shown to demonstrate the advantages of the new compensator and PWM strategy.

• Proceedings of the KIEE Conference
• /
• 2004.11c
• /
• pp.92-94
• /
• 2004

In the previous work, we proposed a new stability criterion for the stability of switched linear systems. By the proposed criterion, we could simply check the stability of switched linear systems because the criterion is applicable to each individual subsystem without need to consider the overall system. Using this criterion, we provided the methods that design a state feedback control when full states are available. In this paper, we apply the same criterion to the case when full states are not available. Unlike existing method such as dwelling time analysis, the proposed method is suitable to a fast switching process because there is no need to consider dwelling time. And we can easily achieve designing multi-controller, multi-estimator, and the supervisor by means of the proposed method.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.51 no.12
• /
• pp.571-576
• /
• 2002

This paper is to develop jumping ring system with three sensor arrays and to control levitated ring using dynamic neural mode. Placing an aluminum ring on the core and switching on an AC source causes the ring to jump in the air due to induced currents. The educational system is composed of 40th optical sensor array, encode circuit, 89C51 microprocessor and control board. The control board consists of power IC, and phase controller. Real time process is present to obtain a height of levitated ring for three different sensor arrays. Based on the educational system and the proposed dynamic neural mode, the height of levitation of the ring is controlled by reference signals. This paper focuses on real system controls using the dynamic neural mode with on line learning algorithm.

• Proceedings of the KIEE Conference
• /
• 1997.07f
• /
• pp.2058-2061
• /
• 1997

A main research topic in PWM inverter drive system is to reduce the generated acoustic noise. One method to reduce the acoustic noise is to cause the switching pattern to be random. This RPWM(Random Pulse Width Modulation) technique for voltage controlled inverters is a kind of good solutions for reduction of acoustic noise and suppression of vibration. This paper describes a carrier frequency modulated real-time RPWM inverter. Changing the carrier frequency randomly, the power spectrum of tile acoustic noise was spread over the wide-band area. And experimental results showed that emitted noise is much more comportable and less annoying

• Proceedings of the KIPE Conference
• /
• 2003.07a
• /
• pp.54-57
• /
• 2003

A new non linear, mean value, instantaneous following control technique to design half bridge converter is proposed in witch control principle uses characteristic that reset time of analog integrator is inverse proportion In input voltage. It is Important characteristic that compensation and follow-up control time are same with switching frequency. Is completed in one cycle that base control frequency. Have excellence characteristic that follow in order instruction value exactly stationary state as well as transient state. Half bridge converter that apply this control principle can know that have stabilize and excellence characteristic. This technique is verified through an experiment, and know that experiment result and theory agree well.

• 제어로봇시스템학회:학술대회논문집
• /
• 1993.10b
• /
• pp.406-411
• /
• 1993

A variable structure control scheme that can be applied to the process with input/output delays are proposed and its control performances are evaluated. The proposed VSCS, which is an output fedback scheme, comprises an integrator for tracking the setpoint and the Smith predictor for compensating the effects of time delay. With The VSCS, the robustness against the parameter variations and external disturbances can be achieved even when the controlled process includes I/O delays. And the desired transient response is obtained by simple adjustment of the coefficients of the switching surface equation.

• International Journal of Korean Welding Society
• /
• v.3 no.1
• /
• pp.2-7
• /
• 2003

Laser welding application for car body manufacturing has many advantages in the stiffness and the lightness of vehicle, the productivity of assembly line, and the degree of freedom in design. This presentation will express the innovation of car body manufacturing including parameter optimization, process modeling, and system integration. In this application the investment for systems was cut down dramatically by real time switching over the laser path between two welding stations. Points of technical discussion are as follows; optimization of parameters such as laser power, robot speed and trajectory, compact and useful design of jig & fixture to assure welding quality for 3 sheet-layer zinc-coated steel, system integration between 4㎾ Nd:YAG laser device and the other systems, on-line real time welding quality monitoring system, perfect safety standards for high power laser, minimization of consumption costs such as arc lamp, protective glass for optic, etc. This application was successfully launched mass production line in 2001. The laser-welded line of side panel consists of 122 stitches totally. And the length is about 2.4m.