• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.30 no.4
• /
• pp.343-350
• /
• 2017

The RC flat plate system has benefits such as a short construction time, an improvement of workability and a floor height reduction. In the case of long span slab, cracking damages and large deflections tend to occur due to the low flexural stiffness of flat plates. Specially, over-loading by self-weight of slab during construction increases short and long-term deflections. These problems may be solved by the use of void slab that has benefits of the reduced self-weight. In this study, to analyze an effect of self-weight reduction of void slab on slab deflections, the parametric study is performed. Including variable conditions such as a concrete strength, a slab construction cycle, the number of shored floors, a compressive reinforcement ratio and a tensile reinforcement ratio, slab construction loads and deflections are calculated by considering the construction stages, concrete cracking, and long-term effects. The short-term deflections during construction and the long-term deflections after construction of both of normal and void slabs are compared and the effects of void slab on the reduction of slab deflections are analyzed.

• Journal of the Korea Concrete Institute
• /
• v.20 no.2
• /
• pp.139-146
• /
• 2008

The characteristics of the biaxial flexural tensile strength of concretes was compared to that of the uniaxial strength. The uniaxial and biaxial strengths in this study were obtained from the classical modulus of rupture test and the biaxial flexural test recently developed by Zi and Oh and Zi et al., respectively. Three different sizes were considered to investigate the effect of the size of aggregates. To estimate the stochastic aspect of the strength, 32 specimens were used for each test. The average biaxial flexural fracture strength was about 20% greater than the uniaxial test. At the same time, the coefficient of variation for the biaxial test was 18% greater than the uniaxial test. This means that the probability of the biaxial cracking can be greater than the uniaxial cracking.

• Journal of Powder Materials
• /
• v.28 no.1
• /
• pp.51-58
• /
• 2021

The conversion of carbon preforms to dense SiC by liquid infiltration is a prospectively low-cost and reliable method of forming SiC-Si composites with complex shapes and high densities. Si powder was coated on top of a 2.0wt.% Y2O3-added carbon preform, and reaction bonded silicon carbide (RBSC) was prepared by infiltrating molten Si at 1,450℃ for 1-8 h. Reactive sintering of the Y2O3-free carbon preform caused Si to be pushed to one side, thereby forming cracking defects. However, when prepared from the Y2O3-added carbon preform, a SiC-Si composite in which Si is homogeneously distributed in the SiC matrix without cracking can be produced. Using the Si + C → SiC reaction at 1,450℃, 3C and 6H SiC phases, crystalline Si, and Y2O3 were generated based on XRD analysis, without the appearance of graphite. The RBSC prepared from the Y2O3-added carbon preform was densified by increasing the density and decreasing the porosity as the holding time increased at 1,450℃. Dense RBSC, which was reaction sintered at 1,450℃ for 4 h from the 2.0wt.% Y2O3-added carbon preform, had an apparent porosity of 0.11% and a relative density of 96.8%.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.47 no.3
• /
• pp.196-200
• /
• 2002

Lower field germination was observed in lipoxygenase- lacking soybean genotypes. This study was performed to understand seed-related traits after accelerated aging in response to planting date of soybeans. Two soybean cultivars, Jinpumkong (null lipoxygenase-2,3) and Jinpumkong 2 (lacking lipoxygenase-1, 2, 3) were evaluated for germination, and were compared with the cultivar, Taekwangkong containing lipoxygenase-1,2,3 isozymes. Greater seed coat cracking was shown in Jinpumkong and Jinpumkong 2 than Taekwangkong. Regardless of soybean genotypes, earlier planting resulted in greater seed coat cracking. After accelerated aging, seed fracturability and hardness of Jinpumkong and Jinpumkong 2 were lower than those of Taekwangkong. There was significant difference in germination percentage among soybean genotypes in response to planting date. Seeds obtained from late planting showed better germination ability. Accelerated aging resulted in lower germination percentages of Jinpumkong and Jinpumkong 2 than that of Taekwangkong, and showed higher electric conductivity in Jinpumkong and Jinpumkong 2 than Taekwangkong. After accelerated aging at 4$0^{\circ}C$ for thirty five days, germination percentages of Jinpumkong and Jinpumkong 2 were lower than that of Taekwangkong. Electric conductivity was increased continually as accelerated aging time became longer, and Jinpumkong and Jinpumkong 2 showed higher electric conductivity than Taekwangkong. Even though there were significant genotype differences in seed traits, further studies are needed to determine whether seed lipoxygenase ability is associated with germination ability.

• Journal of Advanced Information Technology and Convergence
• /
• v.8 no.2
• /
• pp.79-87
• /
• 2018

The current PC user authentication uses character password based on user's knowledge. However, this can easily be exploited by password cracking or key-logging programs. In addition, the use of a difficult password and the periodic change of the password make it easy for the user to mistake exposing the password around the PC because it is difficult for the user to remember the password. In order to overcome this, we propose user gesture recognition and challenge-response authentication. We apply user's hand gesture instead of character password. In the challenge-response method, authentication is performed in the form of responding to a quiz, rather than using the same password every time. To apply the hand gesture to challenge-response authentication, the gesture is recognized and symbolized to be used in the quiz response. So we show that this method can be applied to PC user authentication.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.21 no.1
• /
• pp.39-45
• /
• 2001

Fourier transform has been one of the most common tools to study the frequency characteristics of signals. With the Fourier transform alone, however, it is difficult to tell whether signal's frequency contents evolve in time or not. Except for a few special cases, the frequency contents of most signals encountered in the real world change with time. Time-frequency analysis methods are developed recently to overcome the drawbacks of Fourier transform, which can represent the information of signals in time and frequency at the same time. In this study, damage process of a cross-ply carbon fiber reinforced plastic (CFRP) under monotonic tensile loading was characterized by acoustic emission. Different kinds of CFRP specimens were used to determine the characteristics of AE signals. Time-frequency analysis methods were employed for the analysis of fracture mechanisms in CFRP such as mix cracking, debonding, fiber fracture and delamination.

• Journal of the Korea Concrete Institute
• /
• v.11 no.5
• /
• pp.21-31
• /
• 1999

The companion paper presents an analytical model to predict behaviors of PSC-Beam bridges according to continuity of spans. This paper aims at providing several examples of its application to PSC-Beam bridge. In this regard, many uncertainties affecting to the continuity of spans (such as the ultimate shrinkage strain of slab and girders, the prestressing creep of girders, and the time adopting prestressing force) are analysis in detail. Moreover, to increase the serviceability and to remove th inherent structural defects including the cracking at interior supports, a necessity for the parametric studies of PSC-Beam bridges reflecting the construction sequence is emphasized.

• Journal of Ocean Engineering and Technology
• /
• v.16 no.4
• /
• pp.48-53
• /
• 2002

Fiber-reinforced composites are extensively used in electronic, ship and aerospace applications due to their high strength and high toughess. In these applications, they are often subjected to localized heat damage due to various sources. In order to ensure their reliability, it is important to predict their residual properties using nondestructive evaluation thchniques. Fabric fiber composite specimens were manufactured with six layers of the glass-fiber prepreg and the carbon-fiber prepreg, respectively. The specimens were subjected to a localized heat damage using a heated copper tip with a diameter of 10mm at 35$0^{\circ}C$(CFRP) and 30$0^{\circ}C$(GFRP), respectively. The specimens were then subjected to tension tests while acoustic emission (AE) activities of specimens were collected. The AE activity of all specimens showed three types of distinct frequency regions. Those are matrix cracking, failure of the fiber/matrix interface and fiber breakage.

• Journal of Ocean Engineering and Technology
• /
• v.23 no.6
• /
• pp.111-116
• /
• 2009

The cracking due to hydration heat in mass concrete must be resolved to improve the stability and durability of concrete structures. In this study, the economic efficiency was improved by replacing a copper pipe with a steel one for the heat pipe, and the heat pipe was standardized to significantly improve the operation efficiency, such as the processing, transport, assembly, and construction time. As a result of the experiment, the peak temperature of the ICSHP, ISSHP, and ISUHP specimens decreased by about $7.2{\sim}10.9^{\circ}C$ compared to the OPC specimen and the probability of a thermal crack being generated in the ICSHP, ISSHP, and ISUHP specimens decreased by up to 84~88%.

• Journal of Ocean Engineering and Technology
• /
• v.16 no.6
• /
• pp.55-59
• /
• 2002

Delamination means that cracking occurs on the interface layer between composite laminates. In this paper, to predict the delamination growth in composite laminates subjected to low-velocity impact, the unit load method was introduced, and an eighteen-node 3-D finite element analysis, based on assumed strain mixed formulation, was conducted. Strain energy release rate, necessary to determine the delamination growth, was calculated by using the virtual crack closure technique. The unit load method saves the computation time more than the re-meshing method. The virtual crack closure technique enables the strain energy release rate to be easily calculated, because information of the singular stress field near the crack tip is not required. Hence, the delamination growth in composite laminates that are subjected to low-velocity impact can be efficiently predicted using the above-mentioned methods.