• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.18 no.2
• /
• pp.36-43
• /
• 2004

In this paper, the frequency spectra from respective mechanical noise signals detected using ultrasonic wave and AE(Acoustic Emission) sensor were analysed to under spark generation between brush and commutator side with arbitrarily 15$^{\circ}$ rotation for brush from the DC motor in operation. Also, the frequency spectra from respective magnetizing noise signals detected using ultrasonic wave and AE sensor were analysed to under neutral point for brush from the DC motor in normal operation. And the analyses and comparison between the mechanical noise signal and magnetizing noise signal of ultrasonic wave with brush location change from the DC motor in operation. As the experimental results, tile mechanical noise signal of ultrasonic wave under spark generation between brush and commutator side with brush location change from the DC motor in operation were increased about 2.5∼3.0 times than magnetizing noise signal of ultrasonic wave form the DC motor in normal operation. Also, the main frequency band for mechanical noise signals of AE under spark generation between brush and commutator side with brush location change from the DC motor in operation, appeared about 1.3[MHz]∼l.5[MHz] by the fast fourier transform.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.8
• /
• pp.46-59
• /
• 1998

This paper presents shape design, surface construction, and cutting path generation for the surface of marine ship propeller blades. A propeller blade should be designed to satisfy performance constraints that include operational speed which impacts rotations per minutes, stresses related to deliverable horst power, and the major length of the marine ship which impacts the blade size and shape characteristics. Primary decision variables that affect efficiency in the design of a marine ship propeller blade are the blade diameter and the expanded area ratio. The blade design resulting from these performance constraints typically consists of sculptured surfaces requiring four or five axis contoured machining. In this approach a standard blade geometry description consisting of blade sections with offset nominal points recorded in an offset table is used. From this table the composite Bezier surface geometry of the blade is created. The control vertices of the Hazier surface patches are determined using a chord length fitting procedure from tile offset table data. Cutter contact points and path intervals are calculated to minimize travel distance and production time while maintaining a cusp height within tolerance limits. Long path intervals typically generate short tool paths at the expense of increased however cusp height. Likewise, a minimal tool path results in a shorter production time. Cutting errors including gouging and under-cut, which are common errors in machining sculptured surfaces, are also identified for both convex and concave surfaces. Propeller blade geometry is conducive to gouging. The result is a minimal error free cutting path for machining propeller blades for marine ships.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.8 no.2
• /
• pp.137-145
• /
• 1996

Effects of nonlinear terms on the generation of M$_2$ tide residual elevation and M$_4$ tide in the Yellow Sea and the East China Sea are investigated using a depth-integrated two-dimensional nonlinear M$_2$tidal model. The model domain (117$^{\circ}$E-130$^{\circ}$E, 24$^{\circ}$N-41$^{\circ}$N) covers the whole region of the Yellow Sea and the East China Sea with grid resolution of 1/6$^{\circ}$ in longitude and 1/8$^{\circ}$in latitude. A radiational boundary condition is used along the open boundaries. Calculations show that advection terms yield negative residual elevation, while shallow-water terms in continuity equation yield positive residual elevation. The contribution of both advection terms and shallow-water terms to tile generation of the M$_4$ constituent is more than 90 percents, but that of quadratic bottom friction terms to the M$_4$ constituent is comparatively small.

• Korean journal of applied entomology
• /
• v.16 no.1 s.30
• /
• pp.13-19
• /
• 1977

The smaller brown planthopper overwinters mostly as the fourth instar nymph. The emerged adult disperses to winter barley or wheat plants. The adult of the first generation disperses into the rice field, and spends three generations in the rice field. The population densities of the adults of the first generation and the overall density of the second generations are the most important in relation to the incidents of the rice stripe disease which is transmitted by this insects. This study was intended to analyse the population increases in these important generations in relation to the kind and the different growing stage of the host plants. The insects were reared on potted host plants of different growing stage in the insect cages. The population increases of the insects in the cages were compared with those on the rice seedlings in the laboratory. The results are as follows: 1. The average longevities of the adults of the generations were 13.4 days for the overwintered, 12.9 days for the first, and 10.2 days for the second generation, and showed no significant differences between the generations even they seemed to be shorter than normal condition probably caused by the frequent disturbance at the time of food renewal in 2 or 3 days. 2. When they were reared on the rice seedling, the average numbers of the eggs per female were 131.2 for the overwintered generation, 124.9 for the first generation grown on the barley, and 142.3 for the second generation grown on rice, and shelved no significant differences between the generations. More than $90\%$ of the eggs were laid within 3 weeks. 3. The hatchabilities of the eggs laid on the rice seedling in laboratory were $77.4\%$ for the first generation, $93.1\%$ for the second generation and $62.1\%$ for the third generation. The estimated hatchabilities of the eggs were $67.5\%$ for the first generation, $84.1\%$for the second generation, and $21.9\%$ for the third generation with the growing plants on the plots. The hatchability on the eggs laid by the adults infested on the barley on May 17 was $13.5\%$ compared with $67.5\%$ for the eggs laid by those infested on barley in late April. 4. The average total nymphal periods were 19.4 days for the first generation, and 13.3 days for the second generation in the laboratory and the mortalities of the nymphs seemed to related with the growing stages of the host plants. 5. With the pot experiments, the average per cents of the emerged adults were $37.2\%$ for the first generation, $55.3\%$ for the second generation, and $11.6\%$, for the third generation. The average numbers of the emerged adults were $7.4\%$ for the pots infested on the barley on May 17, instead of $37.2\%$ adults for those infested in late April. 6. From above results, it may suggest that the innate qualities of the insect are not significantly different between generations, and the differences in the increase of the population for the generations might effected considerably by the differences in the physiological conditions of tile host plant, besides the differences in physical and other biological factors.

• 한국HCI학회:학술대회논문집
• /
• 2006.02a
• /
• pp.1246-1251
• /
• 2006

본 연구에서는 영역 분할 알고리즘과 3차 스플라인 보간법을 이용하여 스테인드 글라스 렌더링을 위한 개선된 유리 타일 생성 알고리즘을 제안하였다. 먼저 유리 타일의 초기 형태를 추출하기 위하여 입력 영상에 Mean shift 분할 알고리즘을 적용하였다. Mean shift 분할 알고리즘은 영상의 각 픽셀(pixel)에서의 지역 밀도 최대 점(local density maximum)을 찾아 클러스터링(clustering)하는 알고리즘으로 영상을 효과적으로 분할할 수 있다. 그리고 분할된 영역에서 영역을 사용자 입력으로 병합하고, 영역에서 부적절한 형태를 없애기 위해 본 연구에서는 형태론적 연산(morphological operation)을 이용하였다. 추출된 영역으로부터 유리 타일의 형태로 만들기 위하여 추출된 각각의 영역에 3차 스플라인 보간법(cubic spline interpolation)을 적용하여 경계가 완화된 영역과 납틀(leading)의 형태를 얻는다. 그 다음 영역을 스플라인 곡선(spline curve)을 이용하여 재분할하고, 각 영역에 변환(transformation)된 색상을 적용하여 최종적인 유리 타일을 만들어낸다. 본 연구에서는 3차 스플라인 보간법을 이용하여 실제 스테인드 글라스에서 생길 수 있는 부드러운 경계를 갖는 유리 타일의 형태를 만들어 이를 스테인드 글라스 렌더링에 이용하였다. 이 방법은 기존의 영역 분할 알고리즘에 형태론적 연산만을 적용하여 유리 타일의 형태를 생성하는 것보다 효과적으로 유리 타일의 형태를 생성할 수 있다. 또한, 생성된 영역에 재분할 과정을 거쳐서 작은 유리 타일이 모여서 이루는 조형적인 형태를 이룰 수 있도록 하였다.

• Journal of ILASS-Korea
• /
• v.1 no.2
• /
• pp.24-32
• /
• 1996

Most of the research of small engines to date focused on developing spark ignition engines occupied much parts. Recently the number of a small direct injection diesel engine applied in small cars has been increased and considered as a next generation power source for passenger cars because of its high efficiency. Therefore the combustion chamber becomes smaller and the fuel injection pressure goes higher, which makes fuel sprays impinged easily on the combustion chamber walls. When strong swirls are not induced, the fuel may not mix with air because of fuel deposition on the wall. As a positive way, the combustion chamber systems which is using spray wall impaction has been introduced and assessed by an experimental or a simulate manner. In these systems the raised lands are positioned in tile chamber for spray impaction in order to break up the fuel drops into much smaller and direct them into desirable direction. This study addresses to the effects of rho position and size of the raised land or glow plug to help the chamber design using spray wall impaction. The characteristics of the spray impinged on various lands are investigated and compared with each other. Then the chamber shapes are discussed with the characteristics and their proper position and size is proposed in any chamber volume.

• Korean Management Science Review
• /
• v.23 no.3
• /
• pp.243-257
• /
• 2006

ITU-T's NgN(Next generation Network) architecture is expected to offer a new Internet platforms such as QoS(Quality of Service) guaranteed services as it overcame the limitations of the existing best-effort Internet architecture. However, policy development crucial for the NgN framework(e.g., interconnections and billing) is lagging far behind technology development. For example, arguments over network neutrality clearly indicate little understanding of the Internet industry structure where diverse providers including ISP and CP coexist. This study employs a network economics approach to predict how the competitive landscape involving various providers will evolve under the traffic-based billing system under the NgN environment. Applied is the non-cooperative game theory, in particular, Stackelberg's repeated game in order to build and analyze model for competition among those providers. We also studied possible impacts that CPs would have on the competitive landscape if they have an option to replace ISP: i.e., CDN(Content Delivery Network) provider. Lastly, based on the model analysis and experiments, presented are their implications to policy development and tile future prospect.

• Proceedings of the KIEE Conference
• /
• 2004.07d
• /
• pp.2580-2582
• /
• 2004

In this paper, a Neural Network(NN) based approach for classification of two dimensions images. The proposed algorithm is able to apply in the actual industry. The described diagnostic algorithm is presented to defect surface failures on tiles. A way to get data for a digital image process is several kinds of it. The tiles are scanned and the digital images are preprocessed and classified using neural networks. It is important to reduce the amount of input data with problem specific preprocessing. The auto-associative neural network is used for feature generation and selection while the probabilistic neural network is used for classification. The proposed algorithm is evaluated experimentally using one hundred of the real tile images. Sample image data to preprocess have histogram. The histogram is used as input value of probabilistic neural network. Auto-associative neural network compress input data and compressed data is classified using probabilistic neural network. Classified sample images are determined by human state. So it is intervened human subjectivity. But digital image processing and neural network are better than human classification ability. Therefore it is very useful of quality control improvement.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.7 s.184
• /
• pp.84-92
• /
• 2006

This paper deals with determination of motions of a humanoid robot using genetic algorithm. A humanoid robot has some problems of the structural instability basically. So, we have to consider the stable walking gait in gait planning. Besides, it is important to make the smoothly optimal gait for saving the electric power. A mobile robot has battery to move autonomously. But a humanoid robot needs more electric power in order to drive many joints. So, if movements of walking joint don't maintain optimally, it is hard to sustain the battery power during the working period. Also, if a gait trajectory doesn't have optimal state, the expected lift span of joints tends to be decreased. Also, if a gait trajectory doesn't have optimal state, the expected lift span of joints tends to be decreased. To solve these problems, the genetic algorithm is employed to guarantee the optimal gait trajectory. The fitness functions in a genetic algorithm are introduced to find out optimal trajectory, which enables the robot to have the less reduced jerk of joints and get smooth movement. With these all process accomplished by PC-based program, the optimal solution could be obtained from the simulation. In addition, we discuss the design consideration fur the joint motion and distributed computation of tile humanoid, ISHURO, and suggest its result such as structure of the network and a disturbance observer.

• Korean Journal of Oriental Medicine
• /
• v.2 no.1
• /
• pp.337-380
• /
• 1996

'Nei Jing(內徑)' first defined the interrelationship of the true and tile false between evil factor affecting health(雅氣) and vital essence energy(精氣). According to 「'Nei Jing(內徑)', the above interrelationship is explained as 'If state of evil domination is considered as sthenia-syndrome(雅氣盛則實), if the consumption of healthy energy Is considered as asenia-syndrome(精氣尊則虛): 'Nei Jing(內徑)', proposed major features of the medicall treatment by 'regluate the vatal energy of asthenia and sthenia, treat the sthenia-syndrome by purgation, and treat the asenia-syndrome by therapy of invigoration(調其氣之虛實, 實則瀉之, 虛則補之): The above interrelationship was interpreted as 'treat the asthenia-syndrome of child organ by invigorating the mother organ(虛者補其母)'in the 69th of 'The Classic on Difficulty',(難經 六十九難). Go-Mu(高武) of Myung-dynasty describe therapy for invigoration and purgation of itself-meridian(自經 補瀉法), which locating acupuncture points according to the Therorr of Five Element in the five shu points of itself-meridian(自經 五유穴), based on the generation in the ${\ulcorner}$A Synthetical Book of Acupuncture and Moxibustion(針灸聚英)${\lrcorner}$, Sae-hyun Jang(張世賢) further extended location acupuncture points of the five shu points to the other-meridian in the ${\ulcorner}$Gyeo Jung Do Ju Nan Gyung(校正圖註難經)${\lrcorner}$ Sa-Ahm's 5 Element Acupuncture Method(舍嚴五行鍼法) was originated in 1644, the middle of the Yi-dynasty. It linked the reinforcing and reducing in acupuncture therapy which incorporated tlle asthenia-syndrome and sthenia-syndrome of the hollow organs, based on principle of the Yin Yang 5 Element Theory(陰陽五行學說), not only to the generation in the 5 element(相生關係) but also to the restriction in the 5 element(相剋關係). Furthermore it was devised for the medical treatment by comning therapy for invigoration and purgation of itself-meridian(自經 補瀉法) with that of the other-meridian. Even though many original forms(正形) of the therapy for invigoration and purgation of the Yin Yang 5 Element Theory comply with the principle of the generation and the restriction based on the principle of the Yin Yang 5 Element Theory are abailable, variational forms(變形) are also recognized by examining the nature of the Sa-Ahm's 5 Element Acupuncture Method(舍嚴五行鍼法), For this reason, it is very difficult to understand the Sa-Ahm's 5 Element Acupuncture Method(舍嚴五行鍼法) thoroughly. therefore, those variational forms are obstacles for the beginners to study the Sa-Ahm's 5 Element Acupuncture Method. In order to understand the principle of the practical clinical application of the Sa-Ahm's 5 Element Acupuncture Method, this study investigated which principle was based on the variations of the locating acupuncture points' method for the acupuncture prescription.