• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.30 no.6
• /
• pp.372-375
• /
• 2017

ZnO thin films were deposited by RF magnetron sputtering and then diffused by using an As source in the ampouletube. Also, the ZnO p-n homojunction was made by using As-doped ZnO thin films, and its properties were analyzed. After the As doping, the surface roughness increased, the crystal quality deteriorated, and the full width at half maximum was increased. The As-doped ZnO thin films showed typical p-type properties, and their resistivity was as low as $2.19{\times}10^{-3}{\Omega}cm$, probably because of the in-diffusion from an external As source and out-diffusion from the GaAs substrate. Also, the ZnO p-n junction displayed the typical rectification properties of a p-n junction. Therefore, the As diffusion method is effective for obtaining ZnO films with p-type properties.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.398-401
• /
• 1999

We prepared diamond thin films on WC-Co substrate in a mixtured $H_2-CH_4-O_2$, gas, using 13.%MHz RF PACVD. Scanning electron microscopy, X-ray diffraction and Rarnan spectroscopy were used to analyze the characteristics of thin film, and tribometer of ball-on-disk type were used to test the wear resistance between thin film and substrate. The good diamond quality and wear resistance was appeared with cemented tungsten carbide substrate treated with oxygen plasma.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.402-405
• /
• 1999

The Study of this paper is to establish the optimum fabricating condition of specimens using Vapor Deposition Polymerization Method which belongs to a mode of preparation of functional organic thin films with dry process and to develop thin film type humidity sensor which has good humidity sensitive Characteristics. Scanning electron microscopy Atomic force microscopy were used to analyze the characteristics of thin film and the basic structure of the humidity sensor is a parallel capacitor which consists of three layers of Al/PI/Al. The characteristics of fabricated samples were measured under various conditions and obtained linear characteristics in the range of 20∼80%RH independent of temperature change and low hysteresis characteristics.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.243-246
• /
• 2000

The sputtering systems mainly consist of the three-target holder. The target and substrate were the on-axis type. The MgO and STO substrate were used for the deposition of each layer. The optimum conditions of single-layer thin film were investigated from the SEM images and the XRD patterns. Based on the above conditions, the multi-layer thin films such as YBaCuO/LaGaO/Au/Nb and YBaCuO/Au/Nb were fabricated. The crystalline, the electrical Properties, the energy gap structure and the characteristics of the tunneling barrier on the multi-layer thin film have been investigated and characterized.

• Journal of the Semiconductor & Display Technology
• /
• v.18 no.4
• /
• pp.120-123
• /
• 2019

The effect of surface plasmon on ZTO thin films was investigated. The phenomenon of depletion occurring in the interface of the ZTO thin film created a potential barrier and the dielectric layer of the depletion formed a non-mass particle called plasmon. ZTO thin film represents n-type semiconductor features, and surface current by plasma has been able to obtain the effect of improving electrical efficiency as a result of high current at positive voltage and low current at negative voltage. It can be seen that the reduction of electric charge due to recombination of electronic hole pairs by heat treatment of compound semiconductors induces higher surface current in semiconductor devices.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.04a
• /
• pp.65-66
• /
• 2008

The realization and origin of p-type ZnO are main issue for photoelectronic devices based on ZnO material. N-doped and nominally undoped p-type ZnO films were achieved on silicon (100) and homo-buffer layers by RF magnetron sputtering and post in-situ annealing. The undoped film shows high hole mobility of 1201 $cm^2V^{-1}s^{-1}$ and low resistivity of $0.0454\Omega{\cdot}cm$ with hole concentration of $1.145\times10^{17}cm^{-3}$. The photoluminescence(PL) spectra show the emissions related to FE, DAP and defects of $V_{Zn}$, $V_O$, $Zn_O$, $O_i$ and $O_{Zn}$.

• Journal of the Korean Ceramic Society
• /
• v.40 no.10
• /
• pp.961-966
• /
• 2003

A Multi-Layer Ceramic (MLC) chip type Band-Pass Filter (BPF) using BiNb$\_$0.975/Sb$\_$0.025/ $O_4$ LTCC (Low Temperature Co-fired Ceramics) and MLC processing is presented. The MLC chip BPF has the benefits of low cost and small size. The BPF consists of coupled stripline resonators and coupling capacitors. The BPF is designed to have an attenuation pole at below the passband for a receiver band of IMT-2000 handset. The computer-aided design technology is applied for analysis of the BPF frequency characteristics. The attenuation pole depends on the coupling between resonators and the coupling capacitance. An equivalent circuit and structure of MLC chip BPF are proposed. The frequency characteristics of the manufactured BPF is well acceptable for IMT-2000 application.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07a
• /
• pp.700-702
• /
• 2005

A 5.0-inch transmissive type plastic TFT arrays were successfully fabricated on a plastic substrate at the resolution of $400{\times}3{\times}300$ lines (100ppi). All of the TFT processes were carried out below $150^{\circ}C$ on PES plastic films. After thin film deposition using PECVD, thin film failures such as film delamination and cracking often occurred. For successful growth of thin films (about 1um) without their failures, it is necessary to solve the critical problem related to the internal compressive stress (some GPa) leading to delamination at a threshold thickness value of the films. The Griffith's theory explains the failure process by looking at the excess of elastic energy inside the film, which overcomes the cohesive energy between film and substrate. To increase the above mentioned threshold thickness value there are two possibilities: (i) the improvement of the interface adhesion (for example, through surface micro-roughening and/or surface activation), and (ii) the reduction of the internal stress. In this work, reducing a-Si layer film thickness and optimizing a barrier SiNx layer have produced stable CVD films at 150oC, over PES substrates

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• v.y2005m4
• /
• pp.203-207
• /
• 2005

An experimental study was carried out to investigate the effect of film cooling in the thrust chamber of liquid rocket using LOx and Kerosene as propellant. The heat fluxes were obtained from the measured wall temperature to the axial direction of thrust chamber for different type of coolant, the various O/F ratio, mass flow rate and the location of the film cooling injector. A thin wall combustion chamber and nozzle were used to obtain the heat flux.

• Journal of the Korean Vacuum Society
• /
• v.6 no.S1
• /
• pp.141-153
• /
• 1997

The paraelectric cubic-to-ferroelectric tetragonal phase transition of the thin Pb(Zr, Ti)$O_3$ (PZT) films grown on MgO(001) substrate was investigated in a series of synchrotron x-ray scattering experiments. As the thickness of the film decreases the transition temperature and the amount of the tetragonal distortion were decreased continuously Different from only the c-domains were existent in the thinnest 25nm thick film. Based on this we propose a model for the domain structure of the tetragonal PZT/MgO(100) film that is very different from the ones suggested in literature. We attribute the suppression of the transition to the substrate field that prefers the c-type domains near the interface and suppresses the tetragonal distortion to minimize the film-substrate lattice mismatch.