• Broadcasting and Media Magazine
• /
• v.6 no.4
• /
• pp.57-65
• /
• 2001

• Proceedings of the Korean Magnestics Society Conference
• /
• 1999.10a
• /
• pp.28-29
• /
• 1999

• Journal of Magnetics
• /
• v.18 no.2
• /
• pp.86-89
• /
• 2013

This paper shows a new effective approach to measure crystallization temperature of soft magnetic underlayer (SUL) for next generation of heat assisted perpendicular recording media. This approach uses temperature dependent reflectivity, which shows a clear jump when samples are crystallized. To achieve this measurement, an optical system is set up using hot plate and infrared laser. Reflectivity of SUL $(Co_{70}Fe_{30})_{92}Ta_3Zr_5$ shows a clear jump at its amorphous-crystalline transition temperature. Experiment results show this effect is clear in infrared region, and is weak for visible light.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.208-211
• /
• 2000

We prepared Co-Cr-Ta and Co-Cr-Ta/Ti thin film for perpendicular magnetic recording media by facing targets sputtering system (FTS system). Ti underlayer effects on crystallographic and magnetic characteristics of Co-Cr-Ta perpendicular magnetic recording media have been investigated. Crystallgraphic and magnetic characteristic of prepared thin films were evaluated by x-ray diffractometry(XRD), vibrating sample magnetometer(VSM) and kerr hysteresis loop measurement. The coercivity and anisotropy field increase by introduced Ti underlayer when substrate temperature is higher than 150$^{\circ}C$. The c-axis dispersion angle and grain size of Co-Cr-Ta/Ti thin film is decrease than Co-Cr-Ta when substrate temperature is higher than 100$^{\circ}C$. Consequently, the use of a Ti underlayer highly orientated can be improved crystallographic and magnetic characteristics of Co-Cr -Ta perpendicular media layer.

• Proceedings of the Korean Magnestics Society Conference
• /
• 1994.03a
• /
• pp.12-13
• /
• 1994

Magnetic recording is still considered to be a.leader in storage industries in general. The rigid disk drive, in particular, has an advantage over tape, optical, magneto-optical, or flash memories, because of high areal density and fast access time with reasonably low cost per Mbyte. However, to be competitive in the market and to keep an edge over other storage devices, head and media in rigid disk drives require better performance per cost and more aggressive improvement in areal density, as shown in Fig. 1, than before. In this review paper, the future trend in head/media technologies of the rigid disk drive has been reviewed. Thin film media and thin film inductive/MR heads will be mainly discussed, since they are expected to be dominant in the future high-end drives over other technologies, such as particulate media or MIG heads.(omitted)mitted)

• Journal of Korea Multimedia Society
• /
• v.12 no.9
• /
• pp.1288-1296
• /
• 2009

This paper is for multi-frequency thin film loop antenna used on smart phone, PMP and PDA like as a multi-media devices. We developed a loop pattern folding methods to reduce a thin film antenna dimension using that mutual coupling folding loop occurs the higher frequency resonation. To reduce the thin film size for loop antenna, we fold the loop pattern repeatedly control the coupling coefficient than generate a not only higher mode resonation but also basic resonation from loop pattern. To realization the thin film folded loop antenna, we used a $30mm{\times}9mm$ PI film the thickness is 20um so that we realize the CDMA850, GPS, DCS, PCS, WCDMA antenna simultaneously and it's radiation efficiency is over 50% and gain is 0dBi.

• Journal of the Korean institute of surface engineering
• /
• v.26 no.2
• /
• pp.45-54
• /
• 1993

In this study, magnetic properties of anodized Al film deposited with ferro-magnetic metals in the capacity of perpendicular magnetic recording media were measured and evaluated to find out the role of structure and morphology of the oxide films on magnetic characteristics. The object of this work was to present the conditions of magnetic thin film formation with more superior magnetic property. Anodizing was carried out under various conditions, and then the anodized film were electro-deposited with Co, Ni, Fe and their alloys. Coercive force and residual magnetization in perpendicular direction increased as the pore length of anodized film increased. It was attributed to the increase of the amount of depoisted metals and the ratio of length/diameter of pores. Morphology of anodized films in phosperic acid was not similar to that of sulfuric acid, and thin films in the former solution had perpendcular magnetic anisostropy because of large diameter, irregular length and distribution of the pores. It was found that magnetic properties of the thin films, which had doubled layer of two metals, were dominated by the metal electrodeposited on the surface of the anodized oxide films.

• Journal of Magnetics
• /
• v.14 no.1
• /
• pp.7-10
• /
• 2009

In this work, we studied the effects of Sn addition on the ordering temperature of FePt thin film. The coercivity of FePtSn film was about 1000 Oe greater than the coercivity of FePt film for an annealing temperature of $600^{\circ}C$. Therefore, Sn addition was effective in promoting the $L1_0$ ordering and in reducing the ordering temperature of the FePt film. From our X-ray diffraction results, we found that in the as-deposited film, the addition of Sn induced a lattice expansion in disordered FePt thin films. After the annealing process, the excess Sn diffuses out from the ordered FePt thin film because of the difference in the solid solubility of Sn between the disordered and ordered phases. The existence of precipitates of Sn from the FePt lattice was deduced by Curie temperature measurements of the FePt and FePtSn films. Therefore, the key role played by the addition of Sn to the FePt film can be explained by a reduction in the activation energy for the $L1_0$ order-disorder transformation of FePt which originates from the high internal stress in the disordered phase induced by the supersaturated Sn atoms.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.100-103
• /
• 2001

In order to investigate the magnetic properties of CoCr-based bilayered thin films on kind of underlayer, we introduced amorphous Si layer to Co-Cr(-Ta) magnetic layer as underlayer. With the thickness of CoCr, CoCrTa single layer, crystalline orientation and perpendicular coercivity was improved. It was revealed that by introducing the Si underlayer, the c-axis orientation of CoCr, CoCrTa magnetic layer was improved largely. However, with increasing Si film thickness, perpendicular coercivity and saturation magnetization of Cocr/si, CoCrTa/Si bilayered thin films was decreased. Grain size of bilayered thin films became larger.

• Transactions of the Society of Information Storage Systems
• /
• v.5 no.2
• /
• pp.82-88
• /
• 2009

Understanding the adhesion behavior and characteristics of toner film is required to achieve image and text printing with high quality resolution. Toner can be considered as a thin film coating on a media such as paper or polymer film. Quantitative measurement of adhesion characteristics of the thin film is important to assess the reliability of the system. In this work the main objective was to investigate the adhesion characteristic between the toner and the media by ramp loading scratch test method. The scratch test may be used to obtain quantitative information about the adhesion of the film to the substrate. In the scratch test a diamond tip was used to scratch the surface of the toner film under an increasing normal load until the toner detached or fractured. The critical load (LC) was obtained from the experimental results. Also, the relationship between the critical load and the adhesive strength of the interface between the substrate and the toner was obtained by measuring the normal and tangential forces during the scratch test. Finally, theoretical analysis of the toner scratch characteristics was performed based on Benjamin and Weaver theory, Plowing model, and Laugier model.