• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.438-438
• /
• 2012

은(Ag) 또는 금(Au) 입자를 촉매로 이용하여 습식식각을 통해 선택적으로 짧은 시간동안 단결정 실리콘 웨이퍼의 표면을 텍스쳐링하여 반사방지막 특성을 효과적으로 얻을 수 있다. 일반적으로 금속입자는 주로 금속 이온이 포함된 용액이나, 전기증착법을 통해서 실리콘 웨이퍼 표면에 형성시켰지만, 금속입자의 크기와 분포를 조절하기 어려웠다. 하지만, 최근 진공장비를 이용하여 열증발증착법(thermal evaporation)과 급속열처리법(rapid thermal annealing)을 통해서 금속입자를 대면적으로 크기와 분포를 균일하게 조절할 수 있다. 이러한 현상은 열적 비젖음(thermal dewetting) 현상에 의해 실리콘 표면위에 증착된 금속 박막으로부터 나노입자로 형성할 수 있다. 본 연구에서는 실리콘 (100)기판위에 다양한 크기의 은 또는 금 나노입자를 형성시켜 식각용액에 짧은 시간동안 담그어 식각하여, 텍스쳐링 효과와 반사방지(antireflection) 특성을 분석하였다. 실험을 위해 각각 은 또는 금 박막을 열증발증착법을 이용하여 ~3-8 nm의 두께로 형성시켰으며, 급속가열장치를 이용하여 $500^{\circ}C$에서 5분 동안 열처리하였다. 그리고 탈이온수(de-ionized water)에 불화수소와 과산화수소가 혼합된 식각용액에 1-5분 동안 습식식각을 하였다. 각각의 텍스쳐링 된 샘플의 식각의 상태와 깊이를 관찰하기 위해 field emission scanning electron microscopy (FE-SEM)을 이용하여 측정하였으며, UV-vis-NIR spectrophotometer를 이용하여 300 nm에서 1,200 nm의 반사특성을 분석하였다. 또한 RCWA (rigorous coupled wave analysis) 시뮬레이션을 이용하여 텍스쳐링 된 기하학적구조에 대하여 반사방지막 특성을 이론적으로 분석하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1992.05a
• /
• pp.101-104
• /
• 1992

In-doped CdS thin films have been deposited at 150$^{\circ}C$ by simultaneous thermal evaporation of CdS and In. Deposition rate and film thickness were 8A/sec and about 1um, respectively. Indium doping concentration of films varied as Indium source temperature from 500$^{\circ}C$ to 700˚. Properties of In-CdS films have been investigatied by measurements of electrical resistivity, Hall effect, X-ray diffraction and optical trasmission spectra. The conductivity of these films was always n-type. The resistivity, carrier concentration, mobility and optical band gap dependence on Indium source temperature are reported. Carrier concentration and mobility of In-CdS films increased with increasing Indium source temperature: then they decreased. The variation of the optical band gap of In-CdS thin films are related to carrier concentration.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07a
• /
• pp.70-73
• /
• 2004

Two different $SnO_2$ nanomaterials(nanowires and nanobelts) were synthesized from the thermal evaporation of ball-milled $SnO_2$ powders at $1350^{\circ}C$ without the presence of any catalysts, and their structural properties are then investigated by X-ray diffraction, scanning electron microscopy, and transmission electron microscopy. This investigation reveals that the $SnO_2$ nanowires are single-crystalline and their growth direction is parallel to the [100] direction, and that the $SnO_2$ nanobelts are single crystalline and their shape is zigzag. In addition, photoresponse of a single $SnO_2$ nanowire was performed with light above-gap energy, and different characteristics of photoresponse were obtained for the nanowire at ambient atmosphere and in vacuum.

• Korean Journal of Materials Research
• /
• v.15 no.7
• /
• pp.486-490
• /
• 2005

Thin films of tungsten oxide and nickel oxide were deposited on $Al_2O_3/Si-substrate$ by high vacuum thermal evaporation. The properties of microstructure and crystallinity were analyzed by SEM and XRD respectively. $WO_3$ films without addition of NiO showed polycrystalline structure after annealing at $500^{\circ}C$ for SO min. There were the cracks between the polycrystalline grains and the crack width was increased with the thickness of $WO_3$ films. The cracks in the $WO_3$ films could be controlled by an optimum deposition of NiO on $WO_3$ films and either less or more than the optimum addition fails to suppress the cracks. A process mechanism to suppress the crack has been discussed.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.163-163
• /
• 2000

In this research, we used the ion irradiation technique which has an advantae in improving intentionally the properties of surface and interface in a non-equilibrium, instead of the conventional annealing method which has been known to improve the material properties in the equilibrium stat. Cu/Co multilayered films were prepared on SiN4/SiO2/Si substrates by the electron-beam evaporation for the Co layers and the thermal evaporation for the Cu layers in a high vacuum. The ion irradiation with a 80keV Ar+ was carried out at various ion doses in a high vacuum. Hysteresis loops of the films were investigated by magneto-optical polar Kerr spectroscopy at various experimental conditions. The change of atomic structure of the films before and after the ion irradiation was studied by glancing angle x-ray diffraction, and the intermixing between Co and Cu sublayers was confirmed by Rutherford backscattering spectroscopy. The surface roughness and magneto-resistance were measured by atomic force microscopy and with a four-point probe system, respectively. During the magneto-resistance measurement, we changed temperature and the direction of magnetization. From the results of experiments, we found that the change at the interfaces of the Cu/Co multilayered film induced by ion irradiation cause the change of magnetic properties. According to the change in hysteresis loop, the surface inplane component of magnetic easy axis was isotropic before the ion irradiation, but became anisotropic upon irradiation. It was confirmed that this change influences the axial behavior of magneto-resistance. Especially, the magneto-resistance varied in accordance with an external magnetic field and the direction of current, which means that magneto-resistance also shows the uniaxial behavior.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.562-562
• /
• 2012

Recently, graphene and graphene-based materials such as graphene oxide (GO) or reduced graphene oxide (R-GO) draws a great attention for electronic devices due to their structures of one atomic layer of carbon hexagon that have excellent mechanical, electrical, thermal, optical properties and very high specific surface area that can be high potential for chemical functionalization. R-GO is a promising candidate because it can be prepared with low-cost from solution process by chemical oxidation and exfoliation using strong acids and oxidants to produce graphene oxide (GO) and its subsequent reduction. R-GO has been used as semiconductor or conductor materials as well as sensing layer for bio-molecules or ions. In this work, reduced graphene oxide field-effect transistor (R-GO FET) has been fabricated with ITO extended gate structure that has sensing area on ITO extended gate part. R-GO FET device was encapsulated by tetratetracontane (TTC) layer using thermal evaporation. A thermal annealing process was carried out at $140^{\circ}C$ for 4 hours in the same thermal vacuum chamber to remove defects in R-GO film before deposition of TTC at $50^{\circ}C$ with thickness of 200 nm. As a result of this process, R-GO FET device has a very high stability and durability for months to serve as a transducer for sensing applications.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.212-212
• /
• 2000

Since the first obserbvation of carbon nanotubes, extensive researches have been done for the synthesis using arc discharge, laser vaporization, and plasma-enhanced chemical vapor deposition. Carbon nanotubes have unique physical and chemical properties and can allow nanoscale devices. Vertically aligned carbon nanotubes with high quality on a large area is particularly important to enable both fundamental studies and applications, such as flat panel displays and vacuum microelectronics. we have grown vertically aligned carbon nanotubes on a large area of Si substrates by thermal chemical vapor deposition using C2H2 gas at 750-950$^{\circ}C$. we deposited catalytic metal on Si susbstrate using thermal evaporation. The nanotubes reveal highly purified surface. The carbon nanotubes have multi-wall structure with a hollow inside and it reveals bamboo structure agreed with base growth model. Figure 1 shows SEM micrograph showing vertically aligned carbon nanotubes whih were grown at 950$^{\circ}C$ on a large area (20mm${\times}$30mm) of Si substrates. Figure 2 shows TEM analysis was performed on the carbon nanotubes grown at 950$^{\circ}C$ for 10 min. The carbon nanotubes are multi-wall structure with bamboo shape and the lack of fringes inside the nanotube indicates that the core of the structure is hollow. In our experiment, carbon nanotubes grown by the thermal CVD indicate base growth model.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.91-91
• /
• 2010

현재 나노크기의 나노소자에 대한 관심과 연구가 활발히 진행 중에 있고, 나노소자 제작을 위한 나노구조체 연구에도 탄력을 받고 있다. 나노구조체 연구 중에서도 탄소나노튜브(CNT)와 실리콘이 많이 연구되고 있으나 CNT의 경우 금속과 반도체 등 전기적 특성이 혼재되어 분리기술이 필요하며, 실리콘 기반의 나노구조체들은 공기 중에 노출되었을 경우 자연 산화막 생성에 대한 문제점들이 대두되고 있다. 이러한 기존 나노구조체들의 문제점들을 극복하기 위해 산화물 계열의($InO_3$, ZnO와 $SnO_2$ 등) 나노구조체들이 화학, 광학 및 생화학 센서등의 다양한 응용 연구들이 진행되고 있다. 본 연구에서는 thermal evaporation법으로 tube furnace 장비를 이용하여 온도($500{\sim}900^{\circ}C$)변화에 따른 ZnO nanorod를 성장시켰다. 성장된 ZnO nanorod의 구조적 특성을 확인하기 위하여 전계방출주사전자현미경(SEM)을 측정한 결과 ZnO nanorod들은 직경 50~80nm, 길이는 400~1000nm 이상까지 다양한 직경과 길이를 가지고 성장되었으며 $800^{\circ}C$ 에서 성장된 ZnO nanorod가 가장 곧고 이상적인 nanorod의 형태를 이루는 것을 확인할 수 있었다. Nanorod는 온도가 높아질수록 nanowire로 성장됨에 따라 본 연구에서 $800^{\circ}C$ 에서는 nanorod형태를 이루고 있으나 $900^{\circ}C$에서부터 nanowire의 형태로 성장되었다. 또한 성장된 ZnO nanorod들의 X-선 회절패턴(XRD)을 측정 결과 ZnO의 (002) 우선 배양성 때문에 성장된 nanorod 또한 (002) 방향으로 성장되었음을 확인하였다. 이 연구를 통하여 온도를 조절함으로서 ZnO nanorod의 성장제어가 가능함을 확인하였고, 특성 분석을 통하여 발광소자, Solar Cell로의 응용가능성을 확인하였다.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2002.08a
• /
• pp.754-758
• /
• 2002

In order to reach the high quality of organic thin films such as high mobility for device applications, it is strongly desirable to study the growth properties of pentacene film as a function of evaporation condition. Here, we report the structure and morphology of thermal evaporated pentacene thin film by AFM, SEM, and XRD as a function of the evaporation rate and substrate temperature. These results play a key role in determining the electric performance of organic thin film transistor devices.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.229-229
• /
• 2012

Adhesion of Copper film on the aluminum oxide layer formed by anodizing an aluminum plate was enhanced by applying ion beam mixing method. Forming an conductive metal layer on the insulating oxide surface without using adhesive epoxy bonds provide metal-PCB(Printed Circuit Board) better thermal conductivities, which are crucial for high power electric device working condition. IBM (Ion beam mixing) process consists of 3 steps; a preliminary deposition of an film, ion beam bombardment, and additional deposition of film with a proper thickness for the application. For the deposition of the films, e-beam evaporation method was used and 70 KeV N-ions were applied for the ion beam bombardment in this work. Adhesions of the interfaces measured by the adhesive tape test and the pull-off test showed an enhancement with the aid of IBM and the adhesion of the ion-beam-mixed films were commercially acceptable. The mixing feature of the atoms near the interface was studied by scanning electron microscopy, Auger electron spectroscopy, and X-ray photoelectron spectroscopy.