• Journal of Advanced Marine Engineering and Technology
• /
• 제25권3호
• /
• pp.588-594
• /
• 2001

The aim of this paper is to develop the low temperature vacuum dryer, with low initial investments and operating costs, easy operating method and trouble-free operation Usally operations just below atmospheric pressure, as with direct dryers, but some are built for vacuum operation with pressure as low 50 mmHg abs. The lowers the boiling point to $39^{\circ}C$ The experimental data of quantitative analysis for using practically were obtained by the constant drying rate period and reducing drying rate period according to the temperature of hot water which is the experimental parameters of present experiment. As the results, it took about 20 hours for material to reach about 18% of the final moisture content is order to store products for a long time about 450% of the early moisture content at the beginning of drying and maximum drying rate comes to about 0.30 kg/m2hr at about 350% of the moisture content.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제8권4호
• /
• pp.326-332
• /
• 2008

In this work CdS films were prepared by using chemical bath deposition, which is simple and inexpensive technique suitable for large deposition area. Annealing in air at different temperatures (300, 350, 400, 450 and $500^{\circ}C$) at constant time of 30 min, also for different times (15, 30, 45, 60 and 90 min) at constant temperature ($300^{\circ}C$) is achieved. X-Ray analysis has confirmed the formation of cadmium oxide (CdO) with slight increase in grain size, shift towards lower scattering angle due to relaxation in the tensile strain for deposition films, and structure change from cubic and hexagonal to the hexagonal. From electrical properties, significant increase in electrical conductivity appeared in samples annealed at $300^{\circ}C$ for 60 min, and at $350^{\circ}C$ for 30 min.

• Bulletin of the Korean Chemical Society
• /
• 제11권4호
• /
• pp.343-347
• /
• 1990

A thermal decomposition of the tert-butoxy radical has been studied in the gas phase over the pressure range of 1-200 torr at $413_{\circ}K$ using di-tert-butyl peroxide + trimethylsilane mixtures. The relative rate constants were obtained by studying the competitive reactions between tert-butoxy radical decomposition 4(t-BuO·→ CH_3COCH_3 + CH_3·)$ and hydrogen abstraction reaction from trimethylsilane $(t-BuO·+ HSi(CH_3)_3 → t-BuOH + Si(CH_3)_3)·).$ The conventional RRKM calculations were carried out to compare the observed fall-off behavior of the decomposition rate constant $({\kappa}_d)$ with the theoretical predictions using reasonable values of input parameters. In all cases the calculated half-rate pressure $(P_{1/2})$ were significantly higher than those observed. The failure of RRKM to reproduce the fall-off behavior led us to suggest that not all of vibrational modes contribute to excitation (leading to decomposition) on the same time scale.

• 태양에너지
• /
• 제19권3호
• /
• pp.23-28
• /
• 1999

본 논문에서는 난방용 축열보드에 응용하기 위해서 미세캡슐을 함유한 축열블럭의 열성능 특성을 조사하였다. 상변화 물질인 $CH_3COONa{\cdot}3H_2O$를 미세캡슐 형태로 제조하였고 미세캡슐 함유량이 각각 10%, 20%가 되도록 시멘트 몰타르와 혼합하여 축열블럭을 제작하였다. 축열블럭의 축열 및 방열 특성을 분석하기 위하여 유량과 유입 냉각 온도를 변화시켰다. 실험결과를 보면 미세캡슐 함유량이 증가할 수록 블럭에 축열되는 축열량은 증가를 하였고 방열시간도 증가를 하였다. 그리고 방열과정시 유량이 증가하고 유입 냉각온도가 감소함에 따라 방열시간은 감소하였다. 순수블럭(0% 미세캡슐 함유량)은 방열과정시 총괄 열전달 계수는 시간에 따라서 일정하게 유지를 하지만 축열블럭에서는 시간이 지남에 따라 증가를 하였다.

• 대한토목학회논문집
• /
• 제30권1A호
• /
• pp.53-59
• /
• 2010

최근 들어 적외선을 이용하여 콘크리트 구조물의 결함 또는 공동 등을 평가하려는 비파괴 연구가 활발하게 진행되고 있으며, 이는 유지관리기법의 중요한 부분을 이루고 있다. 적외선 화상분석(Infrared Thermography)을 콘크리트 표면에 적용할 경우, 콘크리트의 표면온도는 표면을 구성하는 재질과 열적특성(비열, 열전도율, 열전달율)에 따라 그 응답이 다르게 나타나게 된다. 서로 다른 배합을 가지는 시멘트 모르타르에서는 공극률이 다르게 구성되고, 표면에서 공극률의 차이는 열에 노출된 뒤, 냉각되는 과정에서 열적 거동이 다르게 평가된다. 한편 이러한 공극률은 강도 및 염화물 확산계수와 같은 역학적/내구적 특성에 영향을 주기도 한다. 본 연구에서는 외부에서 열을 가하여 측정하는 능동방식(active type)을 이용하여, 표면의 온도변화를 분석하였다. 물-시멘트비 55%와 65%인 시멘트 모르타르 시편을 제작하였으며, 공극률, 압축강도, 염화물 확산계수 등의 물리적 특성값들이 평가되었다. 이후 동일한 실내조건(온도 $20{\sim}22^{\circ}C$, 습도 55-60%)에서 적외선 화상분석 기법을 적용하였다. 시간의 경과에 따라 공극을 많이 포함하는 시편의 경우, 표면 온도가 상대적으로 증가하였으며, 온도가 일정해지는 시점(임계시점)이 단축되고 있음을 확인할 수 있었다. 이러한 특성은 콘크리트와 같이 공극과 골재를 가지고 있는 복합재료의 품질 평가에 적용할 수 있음을 시사한다. 한편 공극률과 실험상수를 고려하여, 공극률에 따라 변화하는 임계시간에 대한 계산식을 제안하였다. 본 논문에서는 시멘트 모르타르의 공극량의 변화에 따른 물리적 변화와 이에 따른 열특성 변화가 논의될 것이다.

• Bulletin of the Korean Chemical Society
• /
• 제24권10호
• /
• pp.1470-1474
• /
• 2003

The dynamics of the tertiary conformation of myoglobin (Mb) after photolysis of carbon monoxide was investigated at 283 K solution by probing amide I and II bands using femtosecond IR absorption spectroscopy. Time-resolved spectra in the amide region evolve with 6-12 ps time scale without noticeable subpicosecond dynamics. The spectra measured at 100 ps delay after photolysis is similar to the difference FTIR spectrum at equilibrium. Time-resolved spectra of photoexcited Mb evolve modestly and their amplitudes are less than 8% of those of photolyzed MbCO, indicating that thermal contribution to the spectral evolution in the amide region is negligible. These observations suggest that the conformational relaxation ensuing photolysis of MbCO be complex and the final deoxy protein conformation have been substantially formed by 100 ps, probably with 6- 12 ps time constant.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.1933-1938
• /
• 2004

Nucleate boiling experiments with constant wall temperature of heating surface were performed using R113 for almost saturated pool boiling conditions. A microscale heater array and Wheatstone bridge circuits were used to maintain a constant wall temperature condition and to measure the heat flow rate with high temporal and spatial resolutions. Bubble images during the bubble growth were taken as 5000 frames a sec using a high-speed CCD camera synchronized with the heat flow rate measurements. The geometry of the bubble during growth time could be obtained from the captured bubble images. The bubble growth behavior was analyzed using the new dimensionless parameters for each growth regions to permit comparisons with previous results at the same scale. We found that the new dimensionless parameters can describe the whole growth region as initial and later respectively. The comparisons showed good agreement in the initial and thermal growth regions. The required heat flow rate for the volume change of the observed bubble was estimated to be larger than the instantaneous heat flow rate measured at the wall. Heat, which is different from the instantaneous heat supplied through the heating wall, can be estimated as being transferred through the interface between bubble and liquid even with saturated pool conditions. This phenomenon under a saturated pool condition needs to be analyzed and the data from this study can supply the good experimental data with the precise boundary condition (constant wall temperature).

• 한국화재소방학회:학술대회논문집
• /
• 한국화재소방학회 1996년도 학술발표회
• /
• pp.24-29
• /
• 1996

The objective of this research is to study on the formations of thermal stratification in a room in case of several furniture fires such as trashcan, chair, carpet, sofa, mattress and wardrobe as a fire starter in a residential room by performing the experimental studies. The uniformly distributed fire in case of carpet showed that the ignition and the initial growth period were relatively short while the fully developed period was considerably long. The concentrated fires such as the mattress and wardrobe showed that the ignitions and the initial growth periods were relatively long. When fire spread to only one direction, like the case for the trashcan with a regular shape, there was one peak of temperature profile, and for the irregular shaped furniture such as chair, sofa, mattress and wardrobe, there were two or more peaks. The interface heights for the furniture fires were around 1(m) mataining constant state. However, at the time of the maximum temperature, the interface height was lowered to 0.25(m)-0.75(m) from the floor

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 A
• /
• pp.244-246
• /
• 1996

In an controlled electric machine, the variations of motor parameters such as stator and rotor time constant are caused by the temperature rise, thus it is needed to calculate the accurate parameter through the dynamic characteristic analysis considering the temperature variation. In this paper, the dynamic characteristic analysis method of vector controlled LIM is proposed using coupled magnetic & thermal 2D FEM taking into account the movement.

• 한국세라믹학회지
• /
• 제24권6호
• /
• pp.586-592
• /
• 1987

The role of the strain energy and phase stability in the diffuse phase transition have been investigated in the highly disordered solid solution, (Pb1-xBax)(Zr0.4Ti0.6)O3 (0.2 x 0.4). X-ray diffraction analysis indicates that tetragonality (c/a) decreases with the increasing Ba content. Also as the Ba content increases, phase transition becomes more diffuse and at the same time dielectric relaxation as a function of measured frequencies in the 1KHz-10MHz range occurs very pronouncedly. In the Ba content range, 0.2 x 0.35, hysteresis loops are routinely observed and the loop is observed to narrow shape as the Ba content increases but becomes very slim at 40mol% Ba content. Moreover thermal analysis shows that there is no abrupt change in the thermal expansion coefficient below the apparent transition temperature at which dielectric constant becomes maximum. From the above results, it has been concluded that creation of the strain energy due to the distorthion that occurred during the phase transition suppresses diffuse phase transition.