• Journal of the Korean Geotechnical Society
• /
• v.37 no.10
• /
• pp.5-11
• /
• 2021

The compacted bentonite buffer is one of the most important components in an engineered barrier system (EBS) to dispose of high-level radioactive waste (HLW) produced by nuclear power generation. The compacted bentonite buffer has a crucial role in protecting the disposal canister against the external impact and penetration of groundwater, so it has to satisfy the thermal-hydraulic-mechanical requirements. Even though there have been various researches on the investigation of thermal-hydraulic properties, few studies have been conducted to evaluate mechanical properties for the compacted bentonite buffer. For this reason, this paper conducted a series of unconfined compression tests and obtained mechanical properties such as unconfined compressive strength, elastic modulus, and void ratio of Korean compacted bentonite specimens with different water content and dry density values. The unconfined compressive strength and elastic modulus increased, and the Poisson's ratio decreased a little with increasing dry density. It showed that unconfined compressive strength and elastic modulus were proportional to dry density. However, there was not a remarkable correlation between mechanical properties and water content.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.2
• /
• pp.27-37
• /
• 2019

The shell and tube heat exchangers installed in the propulsion system test complex (PSTC) at the Naro Space Center heats cryogenic helium to 500 K with a heat transfer oil. As the experimental helium outlet temperature was lower than expected (less than 100 K), the boundary layer effect of the heat transfer oil is predicted to be the cause of the performance deterioration. A computational fluid dynamics (CFD) analysis was performed to verify where the boundary layer effect exists; however, the boundary layer effect has no significant impact on the performance of the heat exchanger. An alternative method to improve the performance of the heat exchanger by changing the heat transfer oil has been discussed in this paper. The low viscosity and high thermal conductivity at high temperature (~500 K) of heat transfer oil at the shell-side are required to improve the thermal performance of the heat exchanger. The experimental performance of the heat exchanger, used to exchange heat between the cryogenic helium and hot heat transfer oil at the PSTC are summarized in this paper.

• Nuclear Engineering and Technology
• /
• v.54 no.6
• /
• pp.1947-1953
• /
• 2022

As the plasma facing material in the nuclear fusion reactor, tungsten has to bear the irradiation impact of high energy particles. The surface quality of tungsten may affect its irradiation resistance, and even affect the service life of fusion reactor. In this paper, tungsten samples with different surface quality were polished by mechanical processing, subsequently conducted by D₂⁺ implantation and thermal desorption. D₂⁺ implantation was performed at room temperature (RT) with the irradiation dose of 1 × 10²¹ D₂⁺/m² by 5 keV D₂⁺ ions, and thermal desorption spectroscopy measurements were done from RT to 900 K. In addition, He irradiation was also performed by 50 eV He⁺ ions energy with the fluxes of 5.5 × 10²¹ m^-2s^-1 and 1.5 × 10²² m^-2s^-1, respectively. Results reveal that the hydrogen/helium irradiation behavior are both related to surface quality. Samples with high surface quality has superior D₂⁺ retention behavior with less D₂ retained after implantation. However, such samples are more likely to generate fuzzes on the surface after helium irradiation. Different morphologies (smooth, wavy, pyramids) after helium irradiation also demonstrates that the surface morphology is related to tungsten crystallographic orientation.

• Design & Manufacturing
• /
• v.16 no.4
• /
• pp.34-39
• /
• 2022

Sustained economic development around the world is accelerating resource depletion. Research and development of secondary batteries that can replace them is also being actively conducted. Secondary batteries are emerging as a key technology for carbon neutrality. The core of an electric vehicle is the battery (secondary battery). Therefore, in this study, the temperature change by the heat source of the hammer and the rotational speed (rpm) of the abrasive disc of the Classifier Separator Mill (CSM) was repeatedly calculated and analyzed using the heat flow simulation STAR-CCM+. As the rotational speed (rpm) of the abrasive disk increases, the convergence condition of the iteration increases. Under the condition that the inlet speed of the Classifier Separator Mill (CSM) and the heat source value of the disc hammer are the same, the disc rotation speed (rpm) and the hammer temperature are inversely proportional. As the rotational speed (rpm) of the disc increases, the hammer temperature decreases. However, since the wear rate of the secondary battery material increases due to the strong impact of the crushing rotational force, it is determined that an appropriate rpm setting is necessary. In CSM (Classifier Separator Mill), it is judged that the flow rate difference is not significantly different in the direction of the pressure outlet (Outlet 1) right above the classifier wheel with the fastest flow rate. Because the disc and hammer attachment technology is adhesive, the attachment point may deform when the temperature of the hammer rises. Therefore, it is considered necessary to develop high-performance adhesives and other adhesive technologies.

• Advances in nano research
• /
• v.14 no.5
• /
• pp.435-442
• /
• 2023

Sports activities, including playing tennis, are popular with many people. As this industry has become more professionalized, investors and those involved in sports are sure to pay attention to any tool that improves athletes' performance Tennis requires perfect coordination between hands, eyes, and the whole body. Consequently, to perform long-term sports, athletes must have enough muscle strength, flexibility, and endurance. Tennis rackets with new frames were manufactured because tennis players' performance depends on their rackets. These rackets are distinguished by their lighter weight. Composite rackets are available in many types, most of which are made from the latest composite materials. During physical exercise with a tennis racket, nanocomposite materials have a significant effect on reducing injuries. Materials as strong as graphite and thermoplastic can be used to produce these composites that include both fiber and filament. Polyamide is a thermoplastic typically used in composites as a matrix. In today's manufacturing process, materials are made more flexible, structurally more vital, and lighter. This paper discusses the production, testing, and structural analysis of a new polyamide/Multi-walled carbon nanotube nanocomposite. This polyamide can be a suitable substitute for other composite materials in the tennis racket frame. By compression polymerization, polyamide was synthesized. The functionalization of Multi-walled carbon nanotube (MWCNT) was achieved using sulfuric acid and nitric acid, followed by ultrasonic preparation of nanocomposite materials with weight percentages of 5, 10, and 15. Fourier transform infrared (FTIR) and Nuclear magnetic resonance (NMR) confirmed a synthesized nanocomposite structure. Nanocomposites were tested for thermal resistance using the simultaneous thermal analysis (DTA-TG) method. scanning electron microscopy (SEM) analysis was used to determine pores' size, structure, and surface area. An X-ray diffraction analysis (XRD) analysis was used to determine their amorphous nature.

• Current Photovoltaic Research
• /
• v.12 no.2
• /
• pp.37-40
• /
• 2024

One of the current innovation trends in the solar industry is the increase in the size of silicon wafers. As the wafer size increases, the series resistance of the module rises, highlighting the need for research on methods for cutting and bonding solar cells. Among these, the Infrared (IR) laser scribing technique has been extensively researched. However, there is still insufficient optimization research regarding the thermal damage caused by lasers on the Transparent Conductive Oxide (TCO) layer of Heterojunction (HJT) solar cells. Therefore, in this study, we systematically varied conditions such as IR laser scribing speed, frequency, power, and the number of scribes to investigate their impact on the performance of cut cells under each condition. Additionally, we conducted a comparative analysis of thermal damage effects on the TCO layer based on varying scribing depths.

• Structural Engineering and Mechanics
• /
• v.89 no.2
• /
• pp.103-119
• /
• 2024

The present research investigates the thermodynamically bending behavior of FG sandwich plates, laying on the Winkler/Pasternak/Kerr foundation with various boundary conditions, subjected to harmonic thermal load varying through thickness. The supposed FG sandwich plate has three layers with a ceramic core. The constituents' volume fractions of the lower and upper faces vary gradually in the direction of the FG sandwich plate thickness. This variation is performed according to various models: a Power law, Trigonometric, Viola-Tornabene, and the Exponential model, while the core is constantly homogeneous. The displacement field considered in the current work contains integral terms and fewer unknowns than other theories in the literature. The corresponding equations of motion are derived based on Hamilton's principle. The impact of the distribution model, scheme, aspect ratio, side-to-thickness ratio, boundary conditions, and elastic foundations on thermodynamic bending are examined in this study. The deflections obtained for the sandwich plate without elastic foundations have the lowest values for all boundary conditions. In addition, the minimum deflection values are obtained for the exponential volume fraction law model. The sandwich plate's non-dimensional deflection increases as the aspect ratio increases for all distribution models.

• Fashion & Textile Research Journal
• /
• v.26 no.1
• /
• pp.123-136
• /
• 2024

This study aimed to assess the mobility and thermal comfort of personal protective equipment (PPE) among female healthcare workers, taking into account wearers' physique and PPE protection levels. A total of 16 participants (age: 26.3 ± 8.3 y, height: 161.5 ± 7.3 cm, body weight: 57.1 ± 11.0 kg, BMI: 21.9 ± 3.6), representing diverse body types, underwent four PPE conditions: L (Low_Plastic gown ensemble), M (Medium_Tyvek 400), H (High_Tyvek 800J with Powered Air Purifying Respirator [PAPR]), and E (Extremely high_Tychem 2000 with PAPR, Bib apron, and Chemical-resistant gloves). The mobility protocol consisted of 10 different tasks in addition to donning and doffing. The 10 tasks were repeated twice at an air temperature of 24.3 ± 0.1℃, 59±4%RH. Findings revealed a disproportionate relationship between PPE protection and wearer discomfort. Significant differences in clothing microclimate and total sweat rate were observed between the lowest (L) and highest (E) protection levels (p < 0.01), while distinctions among medium levels were inconclusive. Subjective evaluations favored conditions H and L over M and E (p < 0.05), indicating reduced heat, and humidity, increased comfort, and lower exertion. Instances of mobility discomfort, specially in the small body type group, underscored the need for a suitable PPE size system for Korean adult female medical workers. Furthermore, enhancements in gloves, shoe cover, and PAPR hood designs are essential for improving ease of movement and preventing hindrance.

• Journal of The Korean Society of Integrative Medicine
• /
• v.12 no.3
• /
• pp.61-70
• /
• 2024

Purpose: The Asan Hot Springs are adjacent to the Seoul Metropolitan area and have excellent traffic access. However, a steady decline in tourist numbers followed the decline in the urban population. This study aims to provide participants with a hot springs visit as part of their independent tourism experience and then analyze their feedback to obtain meaningful suggestions to enhance local tourism. Methods: We recruited 12 families interested in taking a two-day, one-night tour, including a visit to the Asan Hot Springs. Participating families were grouped into two cohorts (Type C and Type A) depending on whether they included children aged one to ten. Each family answered a survey regarding their overall satisfaction with the Asan Hot Springs and provided targeted feedback regarding hot spring resorts, accommodations, restaurants, adjacent tourist spots, and tourism costs. Results: Most of the families that participated in the study were residents of Seoul, Incheon, or Kyunggi (74.47%); the majority were two-generation families (75%) with children (75%). The Type C group enjoyed the campsite (55.56%) accommodations at the Asan Hot Springs more than their Type A counterparts. Families visited an average of 3.6 places during their stay, and 61.11% of participating families visited entertainment and tourist attractions, including the Type C visit to the thermal bath. Compared with Type A, Type C families spent more on tourism and were more satisfied with the entertainment and tourist attractions experience. Overall, all study participants were satisfied with the thermal sources. Conclusion: Our results indicate that families with children have a higher added value than visitor groups consisting only of adults. Considering the significant impact on the local economy, the Asan Hot Springs and associated tourist attractions and services should be developed with these visitors in mind.

• Journal of the Korean Society of Industry Convergence
• /
• v.27 no.5
• /
• pp.1051-1059
• /
• 2024

This study aims to identify the effects of coffee grounds on plant growth in order to propose new ways to recycle this waste product. As a way to recycle coffee grounds, the effect of placing coffee grounds on the surface of kidney bean plants on plant growth was investigated by determining the root, stem, leaf front growth, and seed germination rates. To maximize the effectiveness of coffee grounds, the effect of heat treated temperature for coffee grounds on plant growth was investigated. Normal kidney bean growth was checked for seed germination and seedling growth. The germination rate was 80 % for the non-treated case without coffee grounds, but 100% for the coffee grounds treated at 100 ℃ and 250 ℃ of heat treatment. Stem, root, and leaf growth were all improved with the use of coffee grounds compared to the non-treated case. This can be attributed to the organic matter present in the coffee grounds and the fact that coffee grounds are hydrophilic, which makes them more hydrating for plants. The coffee grounds were utilized to enhance plant growth, which could be utilized as a new way to recycle coffee grounds.