• Transactions of the Korean Society of Automotive Engineers
• /
• v.17 no.3
• /
• pp.142-148
• /
• 2009

The direct injection(DI) diesel engine has become a prime candidate for future transportation needs because of its high thermal efficiency. However, nitrogen oxides(NOx) increase in the local high temperature regions and particulate matter (PM) increases in the diffusion flame region within diesel combustion. Therefore, the demand for developing a suitable after treatment device has been increased. NOx absorbing catalysts are based on the concept of NOx storage and release making it possible to reduce NOx emission in net oxidizing gas conditions. This De-NOx system, called the LNT(Lean NOx Trap) catalyst, absorbs NOx in lean exhaust gas conditions and release it in rich conditions. This technology can give high NOx conversion efficiency, but the right amount of reducing agent should be supplied into the catalytic converter at the right time. In this research, a performance characteristics of LNT with a hydrogen enriched gas as a reductant was examined and strategies of controlling the injection and rich exhaust gas condition were studied. The NOx reduction efficiency is closely connected to the injection timing and duration of reductant. LNT can reduce NOx efficiently with only 1 % fuel penalty.

• Applied Microscopy
• /
• v.43 no.4
• /
• pp.173-176
• /
• 2013

The oxidation behavior of the crystallized $Al_{87}Ni_3Y_{10}$ alloy has been investigated with an aim to compare with that of the amorphous $Al_{87}Ni_3Y_{10}$ alloy. The oxidation at 873 K occurs as follows: (1) growth of an amorphous aluminum-yttrium oxide layer (~10 nm) after heating up to 873 K; and (2) formation of $YAlO_3$ crystalline oxide (~220 nm) after annealing for 30 hours at 873 K. Such an overall oxidation step indicates that the oxidation behavior in the crystallized $Al_{87}Ni_3Y_{10}$ alloy occurs in the same way as in the amorphous $Al_{87}Ni_3Y_{10}$ alloy. The simultaneous presence of aluminum and yttrium in the oxide layer significantly enhances the thermal stability of the amorphous structure in the oxide phase. Since the structure of aluminum-yttrium oxide is dense due to the large difference in ionic radius between aluminum and yttrium ions, the diffusion of oxygen ion through the amorphous oxide layer is limited thus stabilizing the amorphous structure of the oxide phase.

• Korean Journal of Food Science and Technology
• /
• v.21 no.6
• /
• pp.857-862
• /
• 1989

Palm oil was crystallized and melted in the differential scanning calorimeter (DSC) in the presence and the absence of sucrose fatty acid ester (SE) at the different scanning rate. In the presence of SE, the crystallization temperature of palm oil was lowered, because SE inhibited the formation of mother crystal at the initial cooling stage The melting curves of SE added palm oil changed irregularly in the ${\alpha}-form$ transition and fusion entropy. It was that the presence of SE affected the molecular diffusion in palm oil.

• Corrosion Science and Technology
• /
• v.7 no.3
• /
• pp.145-151
• /
• 2008

Material degradation such as high temperature oxidation of metallic material is a severe problem in energy generation systems or manufacturing industries. The metallic materials are oxidized to form oxide films in high temperature environments. The oxide films act as diffusion barriers of oxygen and metal ions and thereafter decrease oxidation rates of metals. The metal oxidation is, however, accelerated by mechanical fracture and spalling of the oxide films caused by thermal stresses by repetition of temperature change, vibration and by the impact of solid particles. It is therefore very important to investigate mechanical properties and adhesion of oxide films in high temperature environments, as well as the properties in a room temperature environment. The oxidation tests were conducted for Ni and Ni-Co alloy under high temperature corrosive environments. The hardness distributions against the indentation depth from the top surface were examined at room temperature. Dynamic indentation tests were performed on Ni oxide films formed on Ni surfaces at room and high temperature to observe fractures or cracks generated around impact craters. As a result, it was found that the mechanical property as hardness of the oxide films were different between Ni and Ni-Co alloy, and between room and high temperatures, and that the adhesion of Ni oxide films was relatively stronger than that of Co oxide films.

• Nuclear Engineering and Technology
• /
• v.46 no.4
• /
• pp.513-520
• /
• 2014

In this paper, three types of operational and industrial absorbers used at research reactors, including Ag-In-Cd alloy, $B_4C$, and Hf are selected for sensitivity analyses. Their integral effects on the main neutronic core parameters important to safety issues are investigated. These parameters are core excess reactivity, shutdown margin, total reactivity worth of control rods, thermal neutron flux, power density distribution, and Power Peaking Factor (PPF). The IAEA 10 MW benchmark core is selected as the case study to verify calculations. A two-dimensional, three-group diffusion model is selected for core calculations. The well-known WIMS-D4 and CITATION reactor codes are used to carry out these calculations. It is found that the largest shutdown margin is gained using the $B_4C$; also the lowest PPF is gained using the Ag-In-Cd alloy. The maximum point power densities belong to the inside fuel regions surrounding the central flux trap (irradiation position), surrounded by control fuel elements, and the peripheral fuel elements beside the graphite reflectors. The greatest and least fluctuation of the point power densities are gained by using $B_4C$ and Ag-In-Cd alloy, respectively.

• Korean Journal of Materials Research
• /
• v.8 no.5
• /
• pp.470-473
• /
• 1998

$As^+$ was ion-implanted onto $CoSi_{2}$ thin films formed by rapidly thermal-annealed Co/Ti bilayers. Then the specimens were drive-in annealed at 500~100$0^{\circ}C$ to form ultra-shallow $n^+$p junction diodes and to measure their 1- V characteristics. When drive-in annealed at 50$0^{\circ}C$ for 280 sec., 50 nm thick ultra-shallow junctions were formed and di¬odes showed the best 1- V characteristics with low leakage current. In particular. the leakage current was 2 orders lower than that of diodes formed by using Co monolayer. It was attributed to uniform $CoSi_{2}$/Si interfaces.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.10 s.253
• /
• pp.1284-1292
• /
• 2006

Heat treatment is a controlled heating and cooling process to improve the physical and/or mechanical properties of metal products without changing their shapes. Today finite element method is widely used to simulate lots of manufacturing processes including heat treatment and surface hardening processes, which aims to reduce the number of time- and cost-consuming experimental tryouts. In this study we tried, using this method, to simulate the full carburizing process that consists of carburizing, diffusing and quenching, and to predict the distribution of carbon contents, phase fraction and hardness, thermal deformation and other mechanical characteristics as the results. In the finite element analysis deformation, heat transfer, phase transformation and diffusion effects are taken into consideration. The carburizing process of a lock gear, a part of the car seat recliner, that is manufactured by the fine blanking process is adopted as the analysis model. The numerical results are discussed and partly compared with experimental data. And a combination of process parameters that is expected to give the highest surface hardness is proposed on the basis of this discussion.

• Current Photovoltaic Research
• /
• v.2 no.3
• /
• pp.130-134
• /
• 2014

We have fabricated the selective emitter solar cell using double textured nanowires structure. The $40{\times}40mm2$-sized silicon substrates were textured to form the pyramid-shaped surface and the nanowires were fabricated by metal assisted chemical etching process using Ag nanoparticles, subsequently. The heavily doped and shallow emitters for selectiv eemitter solar cells were prepared through the thermal $POCl_3$ diffusion and chemical etch-back process, respectively. The front and rear electrodes were prepared following conventional screen printing method and the widths of fingers have been optimized. The selective emitter solar cell using double textured nanowires structure achieved a conversion efficiency of 17.9% with improved absorption and short circuit current density.

• Journal of the Korean Ceramic Society
• /
• v.28 no.3
• /
• pp.215-224
• /
• 1991

The synthesis of SrTiO3 powders having high purity and homogeneous submicron particle size was attempted by the oxalate method. The microstructure and dielectric properties of SrTiO3 based boundary layer capacitor (BLC) were investigated. Strontium titanyl oxalate[SrTiO(C2O4)2.4H2O] was prepared from the mixing solution of (Sr, Ti) using oxalic acid(H2C2O4) as a precipitating agent at 8$0^{\circ}C$. The crystalline SrTiO3 powder was obtained by thermal decomposition of the precipitate above $600^{\circ}C$. The crystalline SrTiO3 powder containing Nb2O5 as a dopant, TiO2 and SiO2 as additives was sintered at 1360~144$0^{\circ}C$ in the reducing atmosphere to get semiconductive SrTiO3. Insulating material containing PbO-Bi2O3-B2O3 frit was printed on the sintered semiconductive SrTiO3 and fired at 120$0^{\circ}C$ for 2h to get the grain boundary diffusion.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.156-157
• /
• 2008

반도체 소자 회로의 집적도가 높아짐에 따라 선폭이 감소하였고 고온 공정이 필요하게 되었다. 기존의 반도체 회로 배선 재료인 Al을 사용할 경우 소자의 속도가 느려져서 소자의 신뢰도가 떨어지고 고온공정에서의 문제가 발생되어 이를 해결하기 위한 차세대 배선 물질로 비저항이 낮은 Cu의 사용이 요구되고 있다. 하지만 Cu는 Si와의 확산이 잘 일어나기 때문에 그 사이에서 확산을 막아주는 확산방지막에 대한 필요성이 제기되었고 연구가 활발히 진행되고 있다. 본 논문에서는 Cu와 Si사이의 확산을 방지하기 위한 W-C-N 확산방지막을 물리적 기상 증착법(PVD)중 하나인 RF Magnetron Sputtering 방식을 사용하여 증착하였다. 고온 공정에서의 안정성을 알아보기 위해 $600^{\circ}C$ 부터 $900^{\circ}C$ 까지 $100^{\circ}C$ 단위로 열처리를 하였고 4-point probe 장치를 사용하여 열처리 온도에 따른 비저항 측정을 통해 W-C-N 확산방지막의 특성을 분석하였다.