• Nuclear Engineering and Technology
• /
• 제56권5호
• /
• pp.1777-1780
• /
• 2024

Chemical and thermal characteristics of cation exchange resins were examined after irradiation of gamma rays. The degradation of cation exchange resins was mainly observed at doses of up to 500 kGy, whereas the balance between degradation and cross-linking reactions was sustained at 700 kGy. While the carbon content decreased significantly up to a maximum dose of 500 kGy, it showed an increase at higher doses. Conversely, the oxygen content exhibited a decrease in contrast to the carbon content. The continuous reduction in sulfur content was attributed to the decomposition of sulfonic groups. Gamma-ray irradiation caused a decrease in the initiation temperature of sulfonic groups and PS-DVB, but unlike the chemical properties of cation exchange resins due to gamma-ray irradiation, the thermal properties of resins remained unaffected.

• Fibers and Polymers
• /
• 제5권4호
• /
• pp.289-296
• /
• 2004

The kinetic parameters, including the activation energy E, the reaction order n, and the pre-exponential factor Z, of the degradation of the copolymers based on the poly(L-lactide) (PLLA) or poly(p-dioxanone-co-L-lactide) (PDO/PLLA) and diol-terminated poly(ethylene glycol) (PEG) segments have been evaluated by the single heating methods of Friedman and Freeman-Carroll. The experimental results showed that copolymers exhibited two degradation steps under nitrogen that can be ascribed to PLLA or PDO/PLLA and PEG segments, respectively. However, copolymers exhibited almost single degradation step in air. Although the values of initial decomposition temperature were scattered, copolymers showed the lower maximum weight loss rate and degradation-activation energy in air than in nitrogen whereas the higher value of temperature at the maximum rate of weight loss was observed in air.

• 전기학회논문지P
• /
• 제64권4호
• /
• pp.256-260
• /
• 2015

In this paper, achieved rise temperature distribution about degradation phenomenon of 24 MVA distribution cast resin transformer using CFD(Computational Fluid Dynamics). Usually, life of transformer is depended on temperature distribution of specification region than thermal special quality of transformer interior. Specially, life of transformer by decline of dielectric strength decreases rapidly in case rise by strangeness transformer interior hot spot temperature value permits. Because calculating high-voltage(HV) winding and low-voltage(LV) winding of cast resin transformer and Joule's loss of core for improvement these life, forecasted heat source, and HV winding and LV winding of cast transformer rise temperature distribution of core for supply of electric power and temperature distribution of highest point on the basis of the results. Also, calculated temperature rise limit of cast resin transformer and permission maximum temperature using analysis by electromagnetic heat source. Calculated and forecasted rise temperature distribution by heat source of thermal analysis with calculated result.

• 설비공학논문집
• /
• 제5권3호
• /
• pp.226-233
• /
• 1993

Thermosyphons are simple devices that can passively transport thermal energy over relatively large distance with little temperature degradation. Especially, the thermosyphon system requires no costly energy input and is completely maintenance free. These attributes permit the use of low grade thermal energy for thermal control of structures including the stabilization of highway foundations. This paper presents the experimental results of the snow melting system in which thermosyphon was utilized to ransfer the earth energy to the pavement to remove snow and ice. The test facility, three earth heated and one unheated test panels, is designed to investigate the variables associated with removing snow and ice from pavement surfaces. The results of these test show that the earth heated panel surface temperature is higher $2{\sim}6^{\circ}C$ than unheated panel when the ambient air temperature is $-7^{\circ}C$. The thermal performance of this earth source thermosyphon system for road heating showed that there was no snow on the heated test panels when the snowfall was 5cm average for the region.

• Journal of the Korean Wood Science and Technology
• /
• 제44권5호
• /
• pp.685-694
• /
• 2016

본 연구에서는 반탄화 과정에서 바이오매스 열분해 거동을 열중량 분석과 발생되는 기체분석으로 확인하였다. 반응온도는 $220{\sim}300^{\circ}C$, 승온속도 $10{\sim}30^{\circ}C/min$, 반응시간은 110분으로 고정하여 분석하였다. 백합나무 중량감소율은 $220^{\circ}C$에서 8.01~8.81%, $300^{\circ}C$에서 71.86~77.38%로 나타났으며, $240^{\circ}C$ 이상에서 급격하게 증가하였다. 반면 낙엽송 중량감소율은 $300^{\circ}C$에서 49.58~54.15%로 백합나무와 비교하여 낮았다. 백합나무에 대한 활성화 에너지는 87.32~91.24 kJ/mol으로 승온속도에 따라 큰 차이를 나타내지 않았으며, 낙엽송에 대한 활성화 에너지는 83.85~91.60 kJ/mol으로 나타났다. 반탄화 과정에서 발생하는 가스성분은 대부분 헤미셀룰로오스 유래 성분이었으며 반응온도가 증가하면서 성분의 종류 및 농도도 증가하였다. 백합나무에서는 furfural, acetic acid가 고농도로 검출되었다.

• 비파괴검사학회지
• /
• 제24권5호
• /
• pp.518-524
• /
• 2004

V(z)곡선법을 이용한 코발트기 초내열합금강의 열화도 평가 유용성 유무를 고주파 초음파 탐촉자를 이용하여 실험적으로 검증하였다. 코발트기 초내열 합금이 고온에서 장시간 노출되었을 때 일어나는 미세조직의 변화를 모사하기 위해서 인공열화를 실시하였다. 여로하에 미치는 초음파 음속의 영향을 고찰하고자 10 MHz를 이용하여 펄스-에코법으로 종파의 음속을 측정하고 200 MHz를 사용하여 V(z)곡선법으로 누설탄성표면파의 음속을 측정하였다. 두 초음파의 음속은 열화시간에 따라서 감소하였다 더욱이, 저주파수 종파의 음속변화는 거의 없었지만, 고주파수 누설탄성표면파의 음속변화는 열화시간에 따라서 최대 4.7%의 변화를 나타내었다. 열화에 따른 경도의 변화와 누설탄성표면파의 음속 변화는 양호한 상관관계를 나타내었다. 따라서 열화도 평가에 고주파 탐촉자를 이용한 초음파 현미경의 V(z)곡선법이 유용함을 알 수 있었다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.144.2-144.2
• /
• 2016

Diamond-like carbon (DLC) coatings have been widely applied to the mechanical components, cutting tools due to properties of high hardness and wear resistance. Among them, hydrogenated amorphous carbon (a-C:H) coatings are well-known for their low friction properties, stable production of thin and thick film, they were reported to be easily worn away under high temperature. Non-hydrogenated tetrahedral amorphous carbon (ta-C) is an ideal for industrial applicability due to good thermal stability from high $sp^3$-bonding fraction ranging from 70 to 80 %. However, the large compressive stress of ta-C coating limits to apply thick ta-C coating. In this study, the thick ta-C coating was deposited onto Inconel alloy disk by the FCVA technique. The thickness of the ta-C coating was about $3.5{\mu}m$. The tribological behaviors of ta-C coated disks sliding against $Si_3N_4$ balls were examined under elevated temperature divided into 23, 100, 200 and $300^{\circ}C$. The range of temperature was setting up until peel off observed. The experimental results showed that the friction coefficient was decreased from 0.14 to 0.05 with increasing temperature up to $200^{\circ}C$. At $300^{\circ}C$, the friction coefficient was dramatically increased over 5,000 cycles and then delaminated. These phenomenon was summarized two kinds of reasons: (1) Thermal degradation and (2) graphitization of ta-C coating. At first, the reason of thermal degradation was demonstrated by wear rate calculation. The wear rate of ta-C coatings showed an increasing trend with elevated temperature. For investigation of relationship between hardness and graphitization, thick ta-C coatings(2, 3 and $5{\mu}m$) were additionally deposited. As the thickness of ta-C coating was increased, hardness decreased from 58 to 49 GPa, which means that graphitization was accelerated. Therefore, now we are trying to increase $sp^3$ fraction of ta-C coating and control the coating parameters for thermal stability of thick ta-C at high temperatures.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.229-230
• /
• 2002

This paper presents the hot spot behaviors on the rubbing surface of ventilated disk brake by using finite element method. The depth of asperities on the rubbing surface is usually $2-3\;{\mu}m$ so the real contact area is microscopically. Non-uniform contacts between the disk and the pads lead to high local temperatures, which may cause the material degradation, and develops hot spots, thermal cracking, and brake system failures at the end. High contact asperity flash temperatures in rubbing systems, which is strongly related to the hot spot. It was generally known that high temperature over about $700^{\circ}C$ may form martensite on the cast iron which is material for automotive disk brakes. In this paper, the contact stress, temperature distribution and strain have been presented for the specific asperities of real contact area microscopically by using coupled thermal-mechanical analysis technique.

• 대한약학회:학술대회논문집
• /
• 대한약학회 2003년도 Proceedings of the Convention of the Pharmaceutical Society of Korea Vol.2-2
• /
• pp.237.2-237.2
• /
• 2003

DWP40458 is a novel human thrombopoietin mutein with two additional N-linked glycosylation site. The thermal stability of DWP40458 in both solution and lyophilized form was studied in the temperature range of 4-50$^{\circ}C$, compared with recombinant human TPO (rhTPO). When the aggregation or degradation pattern of DWP40458 and rhTPO solution was characterized by using SDS-PAGE, gel permeation chromatography (GPC) and reverse phase HPLC, it was found that thermostability of DWP40458 was significantly different to rhTPO in the temperature at 25, 40, 40, 50$^{\circ}C$. (omitted)

• 한국전기전자재료학회논문지
• /
• 제27권11호
• /
• pp.730-735
• /
• 2014

In this study, the temperature characteristics of electrostatic capacity and dielectric loss for the sample of Teflon film which is degradated at the $120^{\circ}C{\sim}200^{\circ}C$ temperature range in the oven for 10 hours has been measured in through the applied frequency range of 0.1 kHz~4,800 kHz at temperature of $50^{\circ}C$, $90^{\circ}C$, $130^{\circ}C$, $170^{\circ}C$. Also, in the same conditions, the frequency characteristics of electrostatic capacity and dielectric loss for the sample of Teflon film has been measured in through the applied temperature range of $30^{\circ}C{\sim}70^{\circ}C$ on setting frequency of 0.1 kHz, 1 kHz, 10 kHz, 100 kHz. The results of this study are as follows. When the frequency range of 0.1 kHz~4,800 kHz applied to the sample of Teflon film, the electrostatic capacity has been measured at the temperature of $50^{\circ}C$, $90^{\circ}C$, $130^{\circ}C$, $170^{\circ}C$. Through this measurement, it found that the electrostatic capacity decreased with increasing temperature. Regarding this result, may be it is because the electromagnetic coupling is degraded by thermal degradation. When the sample of Teflon film heated at $280^{\circ}C$ for 10 hours in oven, the dielectric loss has changed from unstable status to stabilizing status with increasing the degradation temperature in the $120^{\circ}C$, $160^{\circ}C$, $200^{\circ}C$ range. In this measurement, the two spectrums of dielectric loss appeared. It considers that this spectrum of dielectric loss appeared in 300 Hz is caused by the molecular motion of the C-F or OH group. Through this study, It found that the electrostatic capacity decreased with increasing frequency and temperature, and there is no change in dielectric loss, although the frequency increases.