• Corrosion Science and Technology
• /
• v.11 no.6
• /
• pp.218-224
• /
• 2012

Liquid droplet impingement erosion (LDIE) known to be generated in aircraft and turbine blades is recently appeared in nuclear piping. UT thickness measurements with both A-scan and B-scan UT inspection equipments were performed for a component estimated as susceptible to LDIE in feedwater heater vent system. The thickness data measured with B-Scan equipment were compared with those of A-Scan. Thermal hydraulic analysis based on ANSYS FLUENT code was performed to analyze the behavior of liquid droplets inside piping. The wall thinning rate and residual lifetime based on both existing Sanchez-Caldera equation and measuring data were also calculated to identify the applicability of the existing equation to the LDIE management of nuclear piping. Because Sanchez-Caldera equation do not consider the feature of magnetite formed inside piping, droplet size, colliding frequency, the development of new evaluation method urgently needs to manage the pipe wall thinning caused by LDIE.

• KIEAE Journal
• /
• v.16 no.4
• /
• pp.71-77
• /
• 2016

Purpose : The energy saving in a residential building (apartment) sector is known as one of the effective solution of energy reduction. In South Korea, the government has recently reinforced regulations associated with the energy performance of buildings. However, there is a lack of research on the methods for the energy performance diagnosis that is used to analyze the wall thermal performance of the existing apartments. Because a reliable diagnosis is necessary to save the building energy, this study analyzed wall thermal performance of an existing apartment in Seoul. Method : This paper applied two methods for analysis of the thermal insulation performance; HFM(Heat Flow Meter) method and ASTR(Air-Surface Temperature Ratio) method. The HFM method is suggested by ISO9869-1 code to measure the thermal performance. The ASTR method is proposed by this study for the simplified In-situ measurement and it uses three temperature data (interior wall surface, interior and exterior air) and the overall heat transfer coefficient. This study conducted the experiment of an existing apartment in Seoul using these methods and analyzed the results. Furthermore, the energy simulation tool of the building was used to suggest retrofit of the building based on the results of measurements. Result : The error rate of HFM method and ASTR method was analyzed in about 17 to 20%. As the results of comparison between the initial design values of the wall and the measured values, the 26% degradation of insulation thermal performance was measured. Lastly, the energy simulation tool of the building shows 10.8% energy savings in accordance with the construction of suggested retrofit.

• Korean Chemical Engineering Research
• /
• v.52 no.2
• /
• pp.266-271
• /
• 2014

The effects of antioxidants on the properties of Polycarbonate/Acrylonitrile-Butadiene-Styrene(PC/ABS) blends were studied for the functions of the screw speed and loaded duration of high shear rate processing in order to investigate the degradation for PC/ABS blends. Tris-(2,4-di-tert-butyl-phenyl phosphate) (A1) and Bis(2,4-dicumylphenyl) pentaerythritol diphosphite (A3) as phosphite antioxidants and Octadecyl 3-(3,5-di-tert-butyl-4-hydroxyphenyl) propionate (A2) as a phenolic antioxidant are used. The thermal properties were detected by TGA and severely decreased, after the processing. The stress-induced and thermal degradation for PC/ABS blends with the antioxidant A3 was retarded better than the others. By using UTM, the mechanical properties also showed individually decreased according to the antioxidants, after the processing, especially, the elongations showed considerable decline behaviors, while the tensile strengths of PC/ABS blends changed very little. For example, in the operating conditions of 1000rpm of screw speed and 20 seconds of loaded period, the elongations decreased from 148% before the processing, to 91.6% with the A1, to 63% with the A2 and to 131% with the A3 after the processing, respectively. In order to get the morphological properties, the size distributions of the dispersed phases for PC/ABS were investigated by SEM analysis and tended to decrease, as the screw speed and loaded period of the processing increased. Therefore, we confirmed that the antioxidant A3 was the best of all of three to inhibit the stress-induced degradation of PC/ABS blends during the high shear rate processing.

• Journal of Hydrogen and New Energy
• /
• v.1 no.1
• /
• pp.1-8
• /
• 1989

The hydriding kinetic mechanism and the change of the hydriding reaction rate of $MmNi_{4.5}Al_{0.5}$ during the thermally induced hydrogen absorption-desorption cycling are investigated. Comparison of the reaction rate data which are obtained by the pressure sweep method with the theoretical rate equations suggests that the hydriding rate controlling step has changed from the dissociative chemisorption of hydrogen molecules at the surface to the hydrogen diffusion through the hydride phase with the increase of the hydriding fraction. These hydriding kinetic mechanism is not changed during the cycling. However, the intrinsic hydriding reaction rate of $MmNi_{4.5}Al_{0.5}$ after 5500 cycles increases significantly comparing with the activated one. It is suggested that the change of the hydriding kinetic behavior due to intrinsic degradation of $MmNi_{4.5}Al_{0.5}$ can be interpreted as follows ; the formation of nickel cluster at the surface of the sample and the host metal atom exchange in bulk by thermal cycling.

• New & Renewable Energy
• /
• v.10 no.1
• /
• pp.20-29
• /
• 2014

The present study investigated the effects of thermal pre-treatment on the enhancement of anaerobic biodegradability of waste activated sludge at varied TS concentration levels. The activated sludges were thermally oxidized for 30 minutes at $80{\sim}200^{\circ}C$ with varied TS concentrations (2%, 4% and 6%). and then, sludge characteristics, solubilization efficiency and methane production yield of thermally pre-treated sludges were analyzed. The higher the temperature in the thermal pre-treatment, the higher the concentration levels of dissolved matters such as $SCOD_{Cr}$, $NH_4{^+}$ and VFAs, which indicates that the thermal pre-treatment facilitates the hydrolysis and acid fermentation. Furthermore, the solubilization efficiency was increased in proportion to the temperature rise at all TS concentrations and was reached at 68.9%, 55.6% and 53.1%, respectively, at $200^{\circ}C$. In the BMP test of the pre-treated sludges, higher methane production yields were observed as 0.313. 0.314 and $0.299m^3\;CH_4/kg\;VS_{add}$ at the condition of TS 2% ($160^{\circ}C$), 4% ($160^{\circ}C$) and 6% ($180^{\circ}C$), respectively, and degradation rate was increased by 84%, 79% and 65% compared with non-pretreated waste activated sludge. These findings suggest the effectiveness of thermal pre-treatment of waste activated sludge for anaerobic biodegradable process.

• Korean Journal of Food Science and Technology
• /
• v.34 no.2
• /
• pp.238-243
• /
• 2002

The effects of concentration and temperature on degradation of anthocyanins of purple-fleshed sweet potato pigment concentrate and a Japanese plum juice were determined over temperature ranges of 60 to $90^{\circ}C$ and 5 to $60^{\circ}C$, respectively. Degradation of anthocyanins in pigment concentrates followed the first-order reaction rate. Activation energies of the pigment solutions ranged 51.29-73.02 kJ/mol, linearly decreasing as concentration increased except the pigment solution of $8.4^{\circ}Brix$ which was not concentrated after extraction. Anthocynins in Japanese plum juice was also degraded by the first-order reaction kinetics with activation energy of 75.80 kJ/mol. Storage life of the beverage was extended with decreasing storage temperature. Pigment was ratained more than 80% until 8 months storage at $5^{\circ}C$.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.9 no.1
• /
• pp.90-98
• /
• 2001

The slow degradation rate of sewage sludge in anaerobic digesters is due to the rate limiting step of sludge hydrolysis. Therefore, the pre-treatment process had been carried out using acidic(pH 1.5, 3, 4, 5) and alkaline(pH9, 10, 13), thermal(50, 100, 150, $200^{\circ}C$) and ultrasonic treatment(400W, 20kHz, 15, 20, 25, 30, 35, 40, 50, 60min). In the best conditions of each treatment, the SCOD ratio(%) of treated/untreared samples were increased 102% in acid(pH5), 986% in alkali(pH13), 959% in thermal($200^{\circ}C$) and 1123% in ultrasonic(35min) treatment. As the result, the ultrasonic treatment was most effective, followed by alkali, thermal, acidic treatment. In the effects of total gas productivity, the thermal($200^{\circ}C$) pretreatment was the highest, followed by thermal($150^{\circ}C$), ultrasonic(90min), alkaline(pH9) and ultrasonic(50min).

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2001.06a
• /
• pp.346-353
• /
• 2001

Zirconia powder containing 3 mol% yttria(3Y-PSZ) with and with out Fe$_2$O$_3$ addition was coated on tile cast iron substrate by plasma spraying method. The erosion experiments were performed at temperatures from $25^{\circ}C$ to $600^{\circ}C$. A gas blast type erosion tester was used to examine erosion behavior of the specimens. The results of 3Y-PSZ coatings showed that tile erosion rate had maximum value at 40$0^{\circ}C$. It coincided with tile results of phase transformation tetragonal phase to monoclinic phase caused by low temperature thermal degradation. The tensile stress relaxation and the micro-hardness improvement significantly influenced on the erosion rate at $600^{\circ}C$. In the case of Fe$_2$O$_3$ added 3Y-PSZ coatings, the erosion rate of tested at $25^{\circ}C$ showed maximum value at 5.0 mol% Fe$_2$O$_3$ added coating. This tendency is caused by the improvement of mechanical properties and the tensile residual stress. The erosion rate at 200'c and 400'L showed significantly decrease by Fe203 addition. This decrease is believed to be the stabilization of the tetragonal phase and the increase of micro-hardness.

• Polymer(Korea)
• /
• v.26 no.3
• /
• pp.353-359
• /
• 2002

High intensity ultrasound has been applied to a series of poly(ethylene oxide) (PEO)/water systems having different molecular weights of PEO. Major interest was focused on the effect of ultrasonic wane on the melt viscosity chemical structure and thermal properties of PEO. The expected role of ultrasound used in this study was to generate macroradicals of PEO chains by the formation and subsequent collapse of bubbles. It was found that the melt viscosity and chemical structure of PEO change significantly depending on the sonication time. For the prolonged sonication, PEO chains were significantly degraded and new end groups were formed by the interplay of various radical species. When the molecular weight of PEO was relatively higher, the crystallization rate was decreased and the intensity of the melting peak was reduced.

• Korean Journal of Food Science and Technology
• /
• v.24 no.3
• /
• pp.232-235
• /
• 1992

Effect of temperature and initial pH were studied on the pH change of MSG solution during heating. The heating temperature and initial pH of 2% MSG solution were in the range of $100{\sim}120^{\circ}C$ and $pH\;2{\sim}9$, respectively. The results showed that the pH of MSG solution was more rapidly decreased as the temperature increased and the initial pH decreased due to pyroglutamic acid formation from MSG thermal degradation. A linear relationship was obtained between pH decreased and logarithmic value of heating time and the decreasing rate constant of pH were calculated from the slope. The pH decreased$({\Delta}pH)$ after 3 hrs of heating was 1.2 at the initial pH 4 and $120^{\circ}C$ and 0.33 at pH 5 and $120^{\circ}C$ while little pH change measured at the range of $pH\;6{\sim}9$. Activation energy calculated for pH decrease during heating was 11.77 and 22.26 kcal/mole at pH 4 and pH 5, respectively.