• Resources Recycling
• /
• v.13 no.3
• /
• pp.3-11
• /
• 2004

Basic studies have been conducted regarding the crystal formation of hydroxyapatite which was produced in the treatment process of phosphate-containing wastewater using calcium ions as the precipitating agent for its employment as the material for artificial bones. The precipitation of hydroxyapatite were conducted in the synthetic solution which simulating human body fluid for its increased applicability. Ca($NO_3$)$_2$$.$$4H_2$O and ($NH_4$)$_2$$HPO_4$ were employed for the precipitation of hydroxyapatite and its composition was analyzed after drying at 80oC. The thermal behavior of precipitate was investigated by examining the change in its crystalline structure according to the sintering temperature. DTA/TG analysis showed that the escape of moisture from the precipitate occurred at ca. $100^{\circ}C$ and the decomposition of ammonia and the evaporation of lattice water were brought about at around $250^{\circ}C$. X-ray diffraction analysis indicated that the thermally treated precipitate consisted mainly of hydroxyapatite. For dried precipitate, the bonds in the component materials which used for the precipitate formation were observed by FT-IR, and after thermal treatment the major bonds in the precipitate were shown to be $OH^{-}$, $PO_4^{3-}$ , and $CO_3^{ 2-}$ , which were main comprising bonds of hydroxyapatite.

• Korean Journal of Materials Research
• /
• v.8 no.7
• /
• pp.621-627
• /
• 1998

The formation of Co-silicide between Co/Zr bilayer on the amorphous and crystalline Si substrates has been investigated. The films of Zr(50$\AA$) and Co(l50$\AA$) were deposited with e-beam evaporation system and were heattreated with the rapid thermal annealing system at the temperatures between 50$0^{\circ}C$ and 80$0^{\circ}C$ with 10$0^{\circ}C$ increments for 30 seconds. The phase identification of Co-silicide was carried out by XRD and the chemical analysis was examined by AES and RBS. The interface morphologies of Co/Zr bilayer films were investigated by cross sectional TEM and HRTEM. $CoSi_2$ was formed epitaxially on the crystalline Si substrate above $700^{\circ}C$ while polycrystalline $CoSi_2$ was grown on the amorphous Si substrate. The formation temperature of Co-silicide on the amorphous Si substrate was about 100 C lower than that on the crystalline Si. The COzSi phase was not identified on the both Si substrates. The formation temperature of first phase of Co-silicide on ColZr bilayer was higher than that on Co mono layer. CoSizlayer formed on the amorphous Si substrate exhibits better uniformity compared to the CoSiz formed on the crystalline substrate. The sheet resistance of CoSiz layer on crystalline Si was lower than that on the amorphous Si at high temperatures.tures.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.1
• /
• pp.101-112
• /
• 2015

II~VI compound semiconductors, $Zn_xCd_{1-x}S$ thin films have been synthesized onto indium-tin-oxide(ITO) coated glass substrates using thermal evaporation technique. The composition ratio x($0{\leq}x{\leq}1$) was varied to fabricate different kinds of $Zn_xCd_{1-x}S$ thin films including CdS(x=0) and ZnS(x=1) thin films. Then, the deposited thin films were thermally annealed at $400^{\circ}C$ to enhance their crystallinity. The chemical composition and electronic structure of films were investigated by using X-ray photoelectron spectroscopy(XPS). The optical energy gaps of the samples were determined by ultra violet-visible-near infrared(UV-Vis-NIR) spectroscopy and were found to vary in the range of 2.44 to 3.98 eV when x changes from 0 to 1. Finally, we measured the THz characteristics of the $Zn_xCd_{1-x}S$ thin films using THz-TDS(time domain spectroscopy) system to identify the capability for electronic and optical devices in THz region.

• Transactions of the Korean hydrogen and new energy society
• /
• v.28 no.4
• /
• pp.401-406
• /
• 2017

When Liquified Natural Gas (LNG) is vaporized into NG for industrial and household usage, tremendous cold energy was transferred from LNG to seawater during phase-changing process. This heat exchanger loop is not only a waste of huge cold energy, but will cause thermal pollution to the coastal fishery area also when cold water was re-injected into the sea. In this study, an innovation design has been performed to reclaim the cold energy for -35 to $62^{\circ}C$ refrigerated warehouse. Conventionally, this was done by installing mechanical refrigeration systems, necessitating tremendous electrical power to drive temperature. A closed loop LNG heat exchangers in series was designed to replace the mechanical or vapor-compression refrigeration cycle by process simulator. The process simulation software of PRO II with provision has been used to simulate this process for various conditions, what to effect on cold energy and used energy for re-liquefaction and evaporation process. In addition, through analysis the effect of the change of LNG supply pressure on sensible and latent heat, optimum operational conditions was suggested for LNG cold energy warehouse.

• Korean Journal of Materials Research
• /
• v.20 no.8
• /
• pp.434-438
• /
• 2010

The selenization process has been a promising method for low-cost and large-scale production of high quality CIGS film. However, there is the problem that most Ga in the CIGS film segregates near the Mo back contact. So the solar cell behaves like a $CuInSe_2$ and lacks the increased open-circuit voltage. In this study we investigated the Ga distribution in CIGS films by using the $Ga_2Se_3$ layer. The $Ga_2Se_3$ layer was applied on the Cu-In-Ga metal layer to increase Ga content at the surface of CIGS films and to restrict Ga diffusion to the CIGS/Mo interface with Ga and Se bonding. The layer made by thermal evaporation was showed to an amorphous $Ga_2Se_3$ layer in the result of AES depth profile, XPS and XRD measurement. As the thickness of $Ga_2Se_3$ layer increased, a small-grained CIGS film was developed and phase seperation was showed using SEM and XRD respectively. Ga distributions in CIGS films were investigated by means of AES depth profile. As a result, the [Ga]/[In+Ga] ratio was 0.2 at the surface and 0.5 near the CIGS/Mo interface when the $Ga_2Se_3$ thickness was 220 nm, suggesting that the $Ga_2Se_3$ layer on the top of metal layer is one of the possible methods for Ga redistribution and open circuit voltage increase.

• Journal of the Semiconductor & Display Technology
• /
• v.6 no.2 s.19
• /
• pp.11-14
• /
• 2007

For the fabrication of blue color organic light emitting diodes(OLED) with a high performance, 2-TNATA [4,4',4"-tris (2-naphthylphenyl-phenylamino)-triphenylamine] as hole injection material and NPB [N,N'-bis (1-naphthyl) -N,N'-diphenyl-1,1'-biphenyl-4,4'-diamine] as hole transport material were deposited on the ITO (indium tin oxide)/glass substrate by the vacuum thermal evaporation. After then, blue color emission layer was deposited using TPM-BiP[(4'-Benzoylferphenyl-4-yl)phenyl-methanone-Diethyl(biphenyl-4-ymethyl)phosphonate] and GDI602 as a light emitting organic material. Finally, the two kinds of OLEDs with the structure of $ITO/2-TNATA/NPB/TPM-BiP/Alq_3/LiF/Al and ITO/2-TNATA/NPB/GDI602/Alq_3/LiF/Al$ were prepared by in-situ deposition. The maximum current density and luminance were found to be about $588\;mA/cm^2\;and\;5239\;cd/m^2$ at 12V for the OLED sample with the structure of $ITO/2-TNATA/NPB/TPM-BiP/Alq_3/LiF/Al$. Color coordinate of blue OLED was x=0.18, y=0.18 (at llV) and the maximum current efficiency was 2.82 cd/A (at 6V) with the peak emission wavelength of 440 nm.

• Journal of the Semiconductor & Display Technology
• /
• v.6 no.2 s.19
• /
• pp.19-23
• /
• 2007

The blue emitting OLEDs using TMP-BiP[(4'-Benzoylferphenyl-4-yl)phenyl-methanone-Diethyl(biphenyl-4-ymethyl) phosphonate] host and DJNBD-1 dopant have been fabricated and characterized. In the device fabrication, 2-TNATA [4,4',4"-tris(2-naphthylphenyl-phenylamino)-triphenylamine] as a hole injection material and NPB [N,N'-bis(1-naphthyl)N,N'-diphenyl-1,1'-biphenyl-4,4'-diamine] as a hole transport material were deposited on the ITO(indium tin oxide)/glass substrate by vacuum thermal evaporation method. Followed by the deposition, blue color emission layer was deposited using TMP-BiP as a host material and DJNBD-1 as a dopant. Finally, small molecule OLEDs with structure of $ITO/2-TNATA/NPB/TMP-BiP:DJNBD-l/Alq_3/LiF/Al$ were obtained by in-situ deposition of $Alq_3$, LiF and Al as the electron transport material, electron injection material and cathode, respectively. The effect of dopant into host material of the blue OLEDs was studied. The blue OLEDs with DJNBD-1 dopant showed that the maximum current and luminance were found to be about 34 mA and $8110\;cd/m^2$ at 11 V, respectively. In addition, the color coordinate was x=0.17, y=0.17 in CIE color chart, and the peak emission wavelength was 440 nm. The maximum current efficiency of 2.15 cd/A at 7 V was obtained in this experiment.

• Journal of Information Display
• /
• v.4 no.2
• /
• pp.1-6
• /
• 2003

In this paper, we demonstrate that the organic electrophosphorescent device is driven by the organic thin film transistor with spin-coated photoacryl gate insulator. It was found that electrical output characteristics in our organic thin film transistors using the staggered-inverted top-contact structure showed the non-saturated slope in the saturation region and the sub-threshold nonlinearity in the triode region, where we obtained the maximum power luminance that was about 90 $cd/m^2$. Field effect mobility, threshold voltage, and on-off current ratio in 0.45 ${\mu}m$ thick gate dielectric layer were 0.17 $cm^2/Vs$, -7 V, and $10^6$ , respectively. In order to form polyimide as a gate insulator, vapor deposition polymerization process was also introduced instead of spin-coating process, where polyimide film was co-deposited by high-vacuum thermal evaporation from 4,4'-oxydiphthalic anhydride (ODPA) and 4,4'-oxydianiline (ODA) and cured at 150${\sqsubset}$for 1hr. It was also found that field effect mobility, threshold voltage, on-off current ratio, and sub-threshold slope with 0.45 ${\mu}m$ thick gate dielectric films were 0.134 $cm^2/Vs$, -7 V, and $10^6$ A/A, and 1 V/decade, respectively.

• Journal of the Korean Vacuum Society
• /
• v.18 no.4
• /
• pp.259-265
• /
• 2009

We fabricated the field effect transistor using single crystalline ZnO nanowires synthesized by a conventional thermal evaporation method and investigated their basic properties under the various conditions such as ultraviolet irradiation, reducing gas and electrolyte. The typical carrier concentration and mobility of the single crystalline ZnO nanowire with a diameter of 100 nm and length of 5 um were $1.30{\times}10^{18}cm^{-3}$ and $15.6cm^2V^{-1}s^{-1}$, respectively. The current of ZnO nanowire under ultraviolet irradiation significantly increased about 400 times higher as compared to in the darkness. In addition, the ZnO nanowire showed typical sensing characteristics for $H_2$ and CO due to well-known surface reactions and typical current-voltage characteristics under the 0.1 M NaCl electrolyte.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.2
• /
• pp.660-667
• /
• 2018

This study examined the optimal manufacturing conditions of RDF using heat-dried sludge from sewage treatment plant in Cheonan with the oil-drying method. The amounts of oil evaporation and oil drying of the heat-dried sludge were measured at different temperatures to evaluate the value of the product. The performance of the product was then measured using a calorimeter and TGA. In addition, the concentration of odor, NH3, H2S, and TVOC during drying was determined using a portable odor-meter. Ingredient analysis was performed by EDS. Considering mass-production, the oil to heat-dried sludge weight ratio was fixed to 4:1. At $130^{\circ}C$, only physical mixing occurred after the instantaneous drying of internal water. Considering the eco-friendly aspects, there was no significant difference in the drying efficiency between $160^{\circ}C$ and $190^{\circ}C$. Therefore, the optimal conditions were a drying temperature of $160^{\circ}C$ within 5 minutes. Finally, the RDF manufactured in this study and fuel used in the thermal power plants were compared. The calorific value was 4,449kcal/kg, the water content was 2% and the ash content was 34%, which is higher than the fuel of thermal power plants. Therefore, it is believed that coal energy as well as wood pellets can be replaced.