• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.8
• /
• pp.166-174
• /
• 2003

Hydrostatic bearings are widely used in precision machines due to their high motion guide accuracy, low friction and high load carrying capacity. It is very useful to estimate the moving characteristics of hydrostatic bearings in the design stage. A new method is suggested for the analysis of fluid film in hydrostatic bearings. A combined mesh of 8 node solid elements with negligible deformation resistance and spring-dashpot elements is used in conjunction with the user subroutine of ABAQUS to represent the fluid film. The mesh can be used to capture the deformation of the bearing structure as well as the varying properties of fluid film. Analysis results from the finite element model are compared with theoretical solutions, results from FLUENT analysis and some previous works. With this method, static and dynamic analyses of the system containing the bearings can be performed efficiently.

• Journal of Families and Better Life
• /
• v.10 no.2
• /
• pp.87-97
• /
• 1992

The resulting rapid urbanization in Korea in several decades caused the problem of housing shortage and the various residential stressors. In spite of the seriousness of the problem. there have been very few studies that analyses systematically the effects of residential stressors on the housing adjustment attitudes and housing management behavior. The purpose of this study is to analyse such effects by identifying, on the basis of a comprehensive theoretical model. For this purpose, 822 housewives were sampled form the household in Seoul and Chonju-City. The main results obtained are as follows. 1) Higher tendency to housing adaptation tan housing adjustment attitudes. The lower level of stress is observed in housing adjustment than housing adaptation. 2) The higher level of housing management behavior is observed in the loser level of residential stress, the smaller level of living space, the higher level of family adaptation ability and social support.

• Journal of Mechanical Science and Technology
• /
• v.20 no.10
• /
• pp.1626-1637
• /
• 2006

The pressure pulsation due to the gear geometry of the gerotor (generalized rotor) pump mainly occurs in an instant that the chamber of the gerotor enters the delivery port and leaves the suction one. Such a pressure pulsation may result in undesirable vibration and noise of pump components as well as cavitation in hydraulic system. Therefore, it is very important to examine the pressure characteristic of the gerotor pump at its design and analysis stages. In this paper, in order to reduce the pressure pulsation in the gerotor pump, the port plate with the relief grooves is designed by referring to as notch of vane pump and relief groove of piston pump. A series of the theoretical analyses on the pressure pulsation is performed in consideration of various design parameters of the port plate, including the installation positions of the port inlet/outlet and the groove width, and the operating conditions such as rotational velocity and delivery pressure.

• Computers and Concrete
• /
• v.13 no.2
• /
• pp.235-253
• /
• 2014

The theoretical basis and the main results of a design procedure, which attempts to provide the optimal layout of ordinary reinforcement in prestressed concrete beams, subjected to bending moment and shear force are presented. The difficulties encountered in simulating the actual behaviour of prestressed concrete beam in presence of coupled forces bending moment - shear force are discussed; particular emphasis is put on plastic models and stress fields approaches. A unified model for reinforced and prestressed concrete beams under axial force - bending moment - shear force interaction is provided. This analytical model is validated against both experimental results collected in literature and nonlinear numerical analyses. Finally, for illustrating the applicability of the proposed procedure, an example of design for a full-scale prestressed concrete beam is shown.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2006.10a
• /
• pp.21-36
• /
• 2006

This paper is a study of the relationships between trade and transshipment in Korea. Through the analysis of the data collected, a comprehensive model has been developed to analyze and predict relationships between trade and transshipment. By using analyses of port and trade evolution in Asia, the model identifies some important results. An application of the model to forecast developments in selected regions in China is also included in this paper. The paper provides a basis for shipping companies to decide on appropriate transshipment port strategies, and provides important theoretical references for Korean ports' development Supported by Shanghai leading Academic Discipline Project, project Number: T0602.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.2
• /
• pp.169-176
• /
• 2005

In this paper, a DC and small-signal AC modeling for the active-clamp, ful1-bridge boost converter is described. Based on the operation principle, the ac part of the converter can be replaced by a dc counterpart. Then, a conceptual equivalent circuit is derived by rearranging the switches. The equivalent circuit for this converter consists of CCM(Continuous conduction mode) boost and DCM(Discontinuous conduction mode) buck converter. The analyses for the equivalent CCM boost and DCM buck converter are done using the model of PWM switch. The theoretical modeling results are confirmed through experiment or SIMPLIS simulation.

• Journal of Power Electronics
• /
• v.14 no.3
• /
• pp.432-443
• /
• 2014

In order to improve the output efficiency of solar cells and to extend the life span of batteries, the input currents of converters are required to be continuous. If low output voltage ripple is required at the same time, it is obvious that the application of basic two-order converters (such as Buck and Boost derived converters) will not be good enough. In this paper, a lot of non-isolated push-pull converters (NIPPCs) with continuous current will be introduced due to their lower current stress, higher efficiency and better EMC performance. By decomposing the converters into push-pull cells, inductor and free-wheeling diodes, two families of NIPPCs based on single inductor and coupled inductor separately are systematically generated. Furthermore, characteristics analyses for some of the generated converters are also shown in this paper. Finally, two prototypes based on the corresponding typical topologies are built in the lab to verify the theoretical outcomes.

• Proceedings of the KIEE Conference
• /
• 2003.07d
• /
• pp.2061-2063
• /
• 2003

This paper presents a method to compensate the drift of solid-state inertial sensors for control applications. A solid-state gyroscope is evaluated via both theoretical and experimental analyses. From the analytical results, a heuristic compensation method for the drift of the gyroscope is proposed. Experimental results on inverted pendulum control show that the proposed method is feasible since compensated signals from the gyroscope are successfully used in the feedback loop to control the inverted pendulum system.

• Journal of Sensor Science and Technology
• /
• v.20 no.2
• /
• pp.102-106
• /
• 2011

This paper presents a design and analysis of an electromagnetic micro generator which can convert low frequency vibration energy to electrical power. The design aspects of the micro generator comprised planar spring, Cu coil and a permanent magnet(NdFeB). Threetype spring designs and four materials(Parylene, FR-4, Cu and Si) were compared to find resonance frequency. It was found that the resonance frequency will be changed according to the spring shape and material. Mechanical and magnetic parameters had been adjusted to optimize the output power through a comprehensive theoretical study.

• Proceedings of the KIEE Conference
• /
• 1993.07b
• /
• pp.1054-1056
• /
• 1993

The displacement amplifying units(DAUs) of the flexure hinge mechanism are used to amplify the displacements from the Piezo actuators using the principle of a lever. We fabricate for two step DAUs with the SUS304(stainless steel) and experiment them. The fabricated four DAUs have all the hinges aligned to a straight line, and differ in the first step ideal gain($4{\times}10,\;6{\times}10,\;8{\times}10,\;10{\times}10$). We measure the input and the output displacements to get the real amplifying gain. The resonant frequencies of these DAUs are also measured. The experimental results are compared with those of the theoretical formula and with those of the numerical analyses.